summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2016-06-18Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
2016-06-18Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2016-06-18warp7: Add README fileMarco Franchi
Add a README file for helping users to install U-Boot into the eMMC. Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18warp7: Fix watchdog resetMarco Franchi
The latest version of warp7 board provides the connection of the WDOG1_B pin to the PMIC. Program the watchdog to enable the WDOG1_B output which causes a POR reset. Based on the imx7dsabresd code. Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18imx: mx6ulevk: change QSPI PAD DSE to 120ohmPeng Fan
The current pad DSE for QSPI is 60ohm. This setting cause too strong drive to clock and data signals. Need to change the DSE to 120ohm for better signal quality. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18imx6ulevk: fix LCD_nPWREN settingPeng Fan
Q901 is PMOS, LCD_nPWREN should be at low voltage then output is 3V3. If LCD_nPWREN is high, output is 2.4V which is not correct. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18imx6ulevk: fix 74LV OE usagePeng Fan
Fix 74LV OE gpio index. gpio index is wrong, so gpio output will not have effect, since we use wrong GPIO5_IO18, but not correct GPIO5_IO8. And at the end of the initialization of 74lv init, should keep OE voltage level at LOW to make 74lv output the correct voltage. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18mx7dsabresd: Fix LCD_PWR_EN output settingYe Li
LCD_PWR_EN controls the G pin of Q13 PMOS which needs low voltage to connect D to S for outputting LCD 3.3V. If LCD_PWR_EN is high, we measured the LCD 3v3 is actually 1.2V. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18mx6sabresd: Allow LVDS backlight to be functional after a kernel rebootMarco Franchi
Currently the LVDS backlight does not work in U-Boot after a “reboot” comand in the kernel. This problem occurs because the kernel uses this pin in PWM mode and U-Boot does not configure the backlight pin as GPIO functionality. So fix the problem by explicitly configuring the backlight pin as GPIO in U-Boot. Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Acked-by: Stefano Babic <sbabic@denx.de> Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-06-18Merge branch 'master' of git://git.denx.de/u-bootStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2016-06-17Orphan dbau1x00 boardsThomas Lange
I no longer have access to such a board Signed-off-by: Thomas Lange <thomas@corelatus.se>
2016-06-13usb: xhci: fsl: Add workaround for USB erratum A008751Sriram Dash
This patch is doing the following: 1. Implementing the errata for LS2080. 2. Adding fixup for fdt for LS2080. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2016-06-13board: am437x-hs: spl: Select right dtb from fitLokesh Vutla
Select a right dtb from FIT for am437x-hs platform. Reported-by: Madan Srinivas <madans@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13ARM: dts: AM572x-IDK Initial SupportSchuyler Patton
Add initial DTS support for AM572-IDK evm. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Schuyler Patton <spatton@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13board: am57xx: fit: add support for selecting dtb dynamicallyLokesh Vutla
FIT allows for a multiple dtb in a single image. SPL needs away to detect the right dtb to be used. Adding support for the same for am57xx platforms. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13board: am57xx: Rename TARGET_BEAGLE_X15 as TARGET_AM57XX_EVMLokesh Vutla
board/am57xx supports all boards based on am57xx. Rename the taget as TARGET_AM57XX_EVM. Fixes: 74cc8b097d9af ("board: ti: beagle_x15: Rename to indicate support for TI am57xx evms") Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13armv8: s32v234: Introduce basic support for s32v234evbEddy Petrișor
Add initial support for NXP's S32V234 SoC and S32V234EVB board. The S32V230 family is designed to support computation-intensive applications for image processing. The S32V234, as part of the S32V230 family, is a high-performance automotive processor designed to support safe computation-intensive applications in the area of vision and sensor fusion. Code originally writen by: Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com> Original-signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com> Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com> Signed-off-by: Eddy Petrișor <eddy.petrisor@nxp.com>
2016-06-13board: arm:: Add support for Broadcom BCM23550Steve Rae
Add support for the Broadcom BCM23550 board. Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-13Merge branch 'master' of git://git.denx.de/u-boot-arcTom Rini
2016-06-13Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini
2016-06-13board: axs10x: Flush entire cache after programming reset vectorAlexey Brodkin
Now when we have support of IOC (IO-Coherency block) cahce operations on regions are tuned to not be dummy stubs if IOC was found and enabled in the core. That makes flush_dcache_range() useless for our purposes here. And since we do need to flush modified reset vector to at least L2 cache (AKA SLC) so other cores will see it via its L1 instruction cache we're using always functional flush_dcache_all() here. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Marek Vasut <marex@denx.de>
2016-06-12arm: at91: Add support for gurnardAndre Renaud
This board is based on Snapper 9G45 which has an Atmel AT91SAM9G45 chip and 128MB of SDRAM. It includes a small LCD, 2xUSB host, SD card, Ethernet and two UARTs. Signed-off-by: Andre Renaud <andre@designa-electronics.com> Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andreas Bießmann <andreas@biessmann.org> [apply CONFIG_BOOTDELAY transition] Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-12arm: dra7xx: Assign omap_vcores based on board typeKeerthy
Currently omap_vcores which holds pmic data is being assigned based on the SoC type. PMIC is not a part of SoC. It is logical to to assign omap_vcores based on board type. Hence over ride the vcores_init function and assign omap_vcores based on the board type. Reported-by: Nishanth Menon <nm@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com>
2016-06-12Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2016-06-10armv8: ls2080aqds: Enable QSPI boot supportYuan Yao
This patch adds QSPI boot support for LS2080AQDS board. The QSPI boot image need to be programmed into the QSPI flash first. Then we can switch to booting from QSPI memory space. Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-10armv8: ls2080aqds: Config QSPI pin mux via FPGA in NAND bootYuan Yao
Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-10armv8: ls2080aqds: disable IFC NOR & QIXIS when QSPI enableYuan Yao
When QSPI is enabled, NOR flash and QIXIS can't be accessed through IFC due to pin mux. Enable I2C QIXIS access and I2C early init to read the sysclk and ddrclk. Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-10armv8: ls2080aqds: Select QSPI CLK div via SCFGYuan Yao
QSPI module output SCLK divisor value is configured through SCFG. Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-10board: ls2080a: Add "mcinitcmd" env for MC & DPL deploymentPratiyush Mohan Srivastava
Environment variable mcinitcmd is defined to initiate MC and DPL deployment from the location where it is stored (NOR, NAND, SD, SATA, USB) during booting. If this variable is not defined then macro MC_BOOT_ENV_VAR will be null and MC will not be booted and DPL will not be applied during U-boot booting. Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-09siemens,am33x: add draco etamin boardHeiko Schocher
In the draco CPU board family, etamin is a new variant with bigger flash and more RAM. Due to new flash that uses larger pages (4K) some changes are necessary because it impacts the MTD partition layout and the ubi mount parameters. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> [trini: Move BOOTDELAY into defconfig, just always be 3 now] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-06-09am335x, dxr2: get ECC sType from I2C eepromHeiko Schocher
read the ECC Type field from the i2c eeprom, instead configuring it static in the U-Boot binary. see RM: Table 26-17. NAND Geometry Information on I2C EEPROM Signed-off-by: Heiko Schocher <hs@denx.de>
2016-06-09am335x, shc: add support for the am335x based bosch shc boardHeiko Schocher
U-Boot SPL 2016.03-rc3-00019-g6dfb4c2-dirty (Mar 09 2016 - 07:40:06) SHC C3-Sample MPU reference clock runs at 6 MHz Setting MPU clock to 594 MHz Enabling Spread Spectrum of 18 permille for MPU Trying to boot from MMC reading u-boot.img reading u-boot.img U-Boot 2016.03-rc3-00019-g6dfb4c2-dirty (Mar 09 2016 - 07:05:35 +0100) Watchdog enabled I2C: ready DRAM: 512 MiB reloc off 1f783000 MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Net: cpsw U-Boot# Signed-off-by: Heiko Schocher <hs@denx.de>
2016-06-08ARM: socfpga: add support for IS1 boardPavel Machek
This adds support for IS1 board. Pretty usual socfpga board, 256MB of RAM, does not have MMC, two SPI chips, one ethernet port, two additional ethernet ports connected to the FPGA. Signed-off-by: Pavel Machek <pavel@denx.de>
2016-06-07board: ge: bx50v3: don't configure the backlight when there's no displayAndrew Shadura
Don't try to configure the backlight when CONFIG_VIDEO_IPUV3 isn't set. Signed-off-by: Andrew Shadura <andrew.shadura@collabora.co.uk>
2016-06-06Merge http://git.denx.de/u-boot-samsungTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: configs/peach-pi_defconfig configs/peach-pit_defconfig
2016-06-06ARM: DRA7xx: Enable FIT for hs platformsLokesh Vutla
Use a single defconfig for all DRA7xx hs platforms by enabling FIT and delete the platform specific defconfigs. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-06strider: Support con-dp flavorDirk Eibach
There is a new strider console flavor with DisplayPort video. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-06gdsys: osd: Allow osdsize on valid screens onlyDirk Eibach
Limit "osdsize"-command to access valid screens only. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-06ioep-fpga: Support intempo compressionDirk Eibach
There is a new "intempo" compression type that can be reported on startup. Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-06-06Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini
2016-06-06ARM64: zynqmp: Add support for standard distro boot commandsMichal Simek
Nand and QSPI are not defined now but this will be extended. Based on selected bootmode boot_targets are rewritten. Patch also contains detection if variables are saved. If yes don't rewrite boot_targets variable. Also move variable setup to the end of file because SCSI needs to be defined before others macros are using it. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Alexander Graf <agraf@suse.de>
2016-06-06microblaze: Move MSR instruction selection to KconfigMichal Simek
Select MSR instructions via Kconfig instead of xparameters.h. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-06-06microblaze: Add option to pass cpu version numberMichal Simek
Toolchain can use some flags by default based on cpu version. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-06-06microblaze: Select compilation flags via KconfigMichal Simek
Remove autogenerated config.mk and select CPU options via Kconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-06-04Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini
2016-06-04Merge git://git.denx.de/u-boot-nand-flashTom Rini
2016-06-04Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2016-06-03freescale: Tweak various Makefiles to remove redundancy, fix aestheticsRobert P. J. Day
No intended functional change, just remove redundancies in some Makefiles, and make whitespace aesthetics uniform. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03board/freescale: Use unified setup_ddr_tlbs for spl boot and non-spl bootShengzhou Liu
We should use unified setup_ddr_tlbs() for spl boot and non-spl boot to make sure 'M' bit is set for DDR TLB to maintain cache coherence. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03powerpc/board: SPL: Enable malloc flag in global data.Sumit Garg
For malloc to work in SPL framework enable GD_FLG_FULL_MALLOC_INIT flag in global data after allocating memory using mem_malloc_init. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
generated by cgit (git 2.34.1) at 2025-01-09 18:05:00 +0000