| Age | Commit message (Collapse) | Author |
|---|
|
- Add SD secure boot target for ls1043ardb.
- Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream
ID and corresponding stream ID in SMMU.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for secure
boto header.
- Error messages during SPL boot are limited to error code numbers
instead of strings to reduce the size of SPL image.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Add QSPI Secure Boot target to enable chain of trust
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Add QSPI Secure Boot target. Also enable sec init.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Add NOR secure boot target. Also enable sec init.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Using changes in this patch we were able to reduce approx 4k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1046ardb/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1046ardb/ls1046ardb.c to keep
only ddr_init and board_early_init_f funcations in case of SPL
build.
3. Changes in ls1046a_common.h & ls1046ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
4. Disable MMC driver from bieng compiled in case of SPL NAND
build and NAND driver from bieng compiled in case of SPL MMC build.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Using changes in this patch we were able to reduce approx 10k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1043ardb/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1043ardb/ls1043ardb.c to keep
only ddr_init and board_early_init_f funcations in case of SPL
build.
3. Changes in ls1043a_common.h & ls1043ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
4. Disable MMC driver from bieng compiled in case of SPL NAND
build and NAND driver from bieng compiled in case of SPL MMC build.
5. Remove I2C driver support from SPL in case of LS1043ARDB.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
|
|
|
|
The RK3399-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3399.
It provides the following feature set:
* up to 4GB DDR3
* on-module SPI-NOR flash
* on-module eMMC (with 8-bit interace)
* SD card (on a baseboad) via edge connector
* Gigabit Ethernet w/ on-module Micrel KSZ9031 GbE PHY
* HDMI/eDP/MIPI displays
* 2x MIPI-CSI
* USB
- 1x USB 3.0 dual-role (direct connection)
- 2x USB 3.0 host + 1x USB 2.0 (on-module USB 3.0 hub)
* on-module STM32 Cortex-M0 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
- USB<->CAN bridge controller
Note that we use a multi-payload FIT image for booting and have
Cortex-M0 payload in a separate subimage: we thus rely on the FIT
image loader to put it into the SRAM region that ATF expects it in.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fixed build warning on puma-rk3399:
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Update the configuration files to support the device tree and driver
model, so do SPL. The device clock and pins configuration are handled
by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Fix build error with sama5d3_xplained_mmc:
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Remove CONFIG_PHY_MICREL as per previous patch:
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Update the configuration files to support the device tree and
driver model, so do SPL. The device clock and pins configuration
are handled by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add back CONFIG_PHY_MICREL to prevent a build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
|
|
|
The board is now manufactured by Aries Embedded GmbH , rename it.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
The Vybrid SoC family has the same display controller unit (DCU)
like the LS1021A SoC. This patch adds platform data, pinmux defines
and clock control to enable the driver for Toradex Colibri Vybrid
module.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB
and convert it to Kconfig.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
|
|
Here with some DM changes as well as the long-standing AT91 DM/DT
conversion patches which I have picked up via dm.
|
|
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
|
|
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
|
|
Update the configuration files to support the device tree and driver
model, so do SPL. The device clock and pins configuration are handled
by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
|
|
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
|
|
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
|
|
Update the configuration files to support the device tree and
driver model, so do SPL. The device clock and pins configuration
are handled by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
|
|
The intention of the removal is the preparation to introduce the
new AT91 PIO pinctrl driver.
Use the union to make the PIO3 and PIO2's registers be together
and make their offset aligned.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This allows us to use the same DRAM init function on all archs. Add a
dummy function for arc, which does not use DRAM init here.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Dummy function on nios2]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This function name shadows a global name but is in fact different. This
is very confusing. Rename it to help with the following refactoring.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The
SOM has a built-in microSD socket, DDR and NAND flash. The development kit
has an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
This have been verified to boot the i.MX6Q version over either SD
on the development kit or NAND built into the SOM. Items in the dtsi file
are specific to the SOM itself. Items in the dts file are in the baseboard.
Future versions of the SOM will come out supporting the same basebord and
potentially future base boards will come out supporting the same SOM.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Explain how to flash the eMMC and how to boot from it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
voltage peak issue
Apply the proper setting for the reserved bits in SetDes Test and System Mode Control register
to avoid the voltage peak issue while we do the IEEE PHY comformance test
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
|
|
Add the delay (10ms) to ensure the clock is stable and to meet the clock-to-reset(1ms) requirement recommended in the AR8033 datasheet
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
|
|
Change the PMIC bulk configuration from auto mode to sync mode to avoid the voltage shutdown issue
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
|
|
initialization
Add the configuration options for display initialization in case we need to
do the display initialization in kernel to support different timing settings
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
|
|
|
|
|
|
spl_mmc.c calls mmc_initialize(). This symbol is provided in
drivers/mmc/mmc.c when CONFIG_GENERIC_MMC is enabled.
The sunxi Kconfig case is an oddball because it redefines
SPL_MMC_SUPPORT.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
[trini: Update arch/arm/cpu/armv8/zynqmp/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
BeagleBone Blue is next grenation of boards from BeagleBoard.org, focusing
on robotics with a TI wl1835 wireless module for connectivity.
This board can be indentified by the BLAx value after A335BNLT (BBB)
in the at24 eeprom:
BLAx: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 4c 41 30 |.U3.A335BNLTBLA2|]
http://beagleboard.org/blue
https://github.com/beagleboard/beaglebone-blue
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Will Newton <willn@resin.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
SeeedStudio BeagleBone Green Wireless (BBGW) is an expansion of the
SeeedStudio Green (BBG) with the Ethernet replaced by a TI wl1835
wireless module.
This board can be indentified by the GW1x value after A335BNLT (BBB)
in the at24 eeprom:
GW1x [aa 55 33 ee 41 33 33 35 42 4e 4c 54 47 57 31 41 |.U3.A335BNLTGW1A|]
http://beagleboard.org/green-wireless
http://wiki.seeed.cc/BeagleBone_Green_Wireless/
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: Stored in at24 eeprom at address 5-16:
hexdump -e '8/1 "%c"' /sys/bus/i2c/devices/0-0050/eeprom | cut -b 5-16
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Will Newton <willn@resin.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with
the Ethernet replaced by a TI wl1835 wireless module.
This board can be indentified by the BWAx value after A335BNLT (BBB)
in the at24 eeprom:
BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|]
http://beagleboard.org/black-wireless
https://github.com/beagleboard/beaglebone-black-wireless
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Will Newton <willn@resin.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
As per the latest pinmux data available for AM572x EVM,
rev A3, input should be enabled on MMC clock lines for
MMC2/2/3 for stable operation.
Further, AM572x TRM, SPRUHZ6, Revised June 2016, in
section 18.4.6.1.1 "Pad Configuration Registers" states
that input should be enabled for MMC 2/3/4 clock lines.
Enable input on MMC1 and MMC3 clock to match the latest
pinmux data. Input is already enabled on MMC2 clock for
BeagleBoard x15. Further, input is already enabled on all
MMCx clocks for other AM57xx boards (AM572x and AM571x
IDK).
Tested with HS and UHS SD card on AM572x EVM Rev A3.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The Sunchip CX-A99 is a board used in some media players. It features:
An Allwinner A80 ARM SoC (4 * Cortex-A7 + 4 * Cortex-A15 cores)
2 GiB or 4 GiB DDR3 DRAM
AXP808 PMIC
16 GB or 32 GB eMMC
SDIO Wifi/Bluetooth/FM module
SD card slot
1 USB 3.0 connector
2 USB 2.0 connectors
SATA connector
UART connector (internally) for serial console
Ethernet connector (10/100/1000 Mbit/s)
HDMI connector
Composite video and analog audio connector
S/PDIF connector
IR remote control receiver
This patch adds a defconfig for the board. The DRAM settings are as found
in the vendor sys_config.fex file.
It has a preliminary device tree for use until a device tree is accepted
upstream, after which it can be replaced by the upstream version.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
[squash commits, and edited new meanful commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Introduce a new sunxi-spl-with-ecc.bin image with already the right header,
ECC, randomizer and padding for the BROM to be able to read it.
It needs to be flashed using a raw access to the NAND so that the
controller doesn't change a thing to it, since we already have all the
right parameters.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Remove the board_power_init() function.
It will be initialized with device-tree.
In future, it will be controlled with regulator API.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Remove the unused functions.
Never call the get_soft_i2c_scl/sda_pin() aynwhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Remove the board_i2c_init() function.
i2c should be initialized with device-tree file.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
