summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2013-10-02Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-09-27mx35pdk: Fix error handling in board_late_init()Fabio Estevam
If smc911x_initialize() fails we should return the error immediately. While at it, also check the error from cpu_eth_init(). Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2013-09-27mx28evk: Propagate the error if cpu_eth_init() failsFabio Estevam
If cpu_eth_init() fails we should return the error immediately. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
2013-09-27mx28evk: Propagate the error if cpu_eth_init() failsFabio Estevam
If cpu_eth_init() fails we should return the error immediately. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20am335x:Handle worst case scenario for Errata 1.0.24Steve Kipisz
In Errata 1.0.24, if the board is running at OPP50 and has a warm reset, the boot ROM sets the frequencies for OPP100. This patch attempts to drop the frequencies back to OPP50 as soon as possible in the SPL. Then later the voltages and frequencies up set higher. Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> [trini: Adapt to current framework] Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20am335x_evm: am33xx_spl_board_init function and scale core frequencyTom Rini
Add a am33xx_spl_board_init (and enable the PMICs) that we may see, depending on the board we are running on. In all cases, we see if we can rely on the efuse_sma register to tell us the maximum speed. In the case of Beaglebone White, we need to make sure we are on AC power, and are on later than rev A1, and then we can ramp up to the PG1.0 maximum of 720Mhz. In the case of Beaglebone Black, we are either on PG2.0 that supports 1GHz or PG2.1. As PG2.0 may or may not have efuse_sma set, we cannot rely on this probe. In the case of the GP EVM, EVM SK and IDK we need to rely on the efuse_sma if we are on PG2.1, and the defaults for PG1.0/2.0. Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20mx28evk: Fix checkpatch warningFabio Estevam
Fix the following checkpatch warning: $ ./tools/checkpatch.pl -F board/freescale/mx28evk/mx28evk.c CHECK: Alignment should match open parenthesis #109: FILE: freescale/mx28evk/mx28evk.c:109: + writel(CLKCTRL_ENET_TIME_SEL_RMII_CLK | CLKCTRL_ENET_CLK_OUT_EN, + &clkctrl_regs->hw_clkctrl_enet); Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20mx6slevk: Add Ethernet supportFabio Estevam
mx6slevk has a SMSC8720 connected in RMII mode. Add support for it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20mx6qsabreauto: Return error if cpu_eth_init() failsFabio Estevam
Currently board_eth_init() always return 0, but we should propagate the error when cpu_eth_init() fails. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20mx6sabresd: Return error if cpu_eth_init() failsFabio Estevam
Currently board_eth_init() always return 0, but we should propagate the error when cpu_eth_init() fails. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20mx6sabresd: Reset counter to prevent error messageFabio Estevam
If a HDMI cable is not connected, the following message is seen on boot: CPU: Freescale i.MX6Q rev1.1 at 792 MHz Reset cause: POR Board: MX6-SabreSD DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 No panel detected: default to HDMI unsupported panel HDMI Reset the 'i' variable to fix the 'unsupported panel' message. This follows the same idea of commit 47ac53d7ae (imx: nitrogen6x/mx6qsabrelite: Fix bug in board_video_skip). Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20mx6sabresd: Avoid hang when HDMI cable is not connectedFabio Estevam
Since commit d9b894603 (mx6sabresd: Add LVDS splash screen support) the following hang happens if the HDMI cable is not connected or the 'panel' variable is not set: U-Boot 2013.10-rc2-12978-g47ac53d-dirty (Sep 11 2013 - 15:07:38) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Board: MX6-SabreSD DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 ... Provide a check to 'dev->detect' in order to prevent the hang. Reported-by: Pardeep Kumar Singla <b45784@freescale.com> Suggested-by: Eric Bénard <eric@eukrea.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-13Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic
Conflicts: MAINTAINERS boards.cfg Signed-off-by: Stefano Babic <sbabic@denx.de>
2013-09-12Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2013-09-11Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD
Conflicts: tools/Makefile
2013-09-11apf27: add FPGA support for the apf27 boardtrem
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr> Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org> Acked-by: Stefano Babic <sbabic@denx.de>
2013-09-11apf27: add support for the armadeus APF27 boardtrem
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr> Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org> Signed-off-by: Nicolas Colombain <nicolas.colombain@armadeus.com>
2013-09-11arm:goni:mmc: Add sd card detection and initialization.Przemyslaw Marczak
This change allow to use sd card on Goni the same like mmc 0. SD card is mmc dev 1, so it can be used like this: "fatls mmc 1:2". SD card is inited even if eMMC initialization fails. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Minkyu Kang <mk7.kang@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-09-11dts: samsung: arndale: Fix include pathChander Kashyap
As per new convention ARCH_CPU_DTS is not defined in "dtc/Makefile". Hence Arndale comilation is failing. Fix this by adding proper include file in "board/samsung/dts/exynos5250-arndale.dts". Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-09-10imx: nitrogen6x/mx6qsabrelite: Fix bug in board_video_skipRobert Winkler
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
2013-09-10ARM: mxs: Add SanDisk Sansa Fuze+ boardMarek Vasut
Add STMP3780-based Sansa Fuze+ board. This board is a small PMP device sporting a CPU which was later rebranded to i.MX233 . Currently supported is USB gadget mode and MMC . Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
2013-09-10ARM: mxs: Add Creative ZEN XFi3 boardMarek Vasut
Add STMP3780-based XFi3 board. This board is a small PMP device sporting a CPU which was later rebranded to i.MX233 . Currently supported is USB gadget mode and both external SD and internal Phison SD-NAND bridge . Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
2013-09-10mx6sabresd: Add LVDS splash screen supportFabio Estevam
mx6sabresd boards can be connected to a Hannstar XGA LVDS panel. Add support for displaying U-boot splashscreen on it. By default, HDMI splash is selected. In order to use splash via LVDS, do the following in the U-boot prompt: setenv panel Hannstar-XGA save and reboot. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-10ARM: mxs: Receive r0 and r1 passed from BootROMMarek Vasut
Make sure value in register r0 and r1 is preserved and passed to the board_init_ll() and mxs_common_spl_init() where it can be processed further. The value in r0 can be configured during the BootStream generation to arbitary value, r1 contains pointer to return value from CALL'd function. This patch also clears the value in r0 before returning to BootROM to make sure the BootROM is not confused by this value. Finally, this patch cleans up some comments in the start.S file. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
2013-09-09Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xxTom Rini
2013-09-09Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
2013-09-09SPL: P1022DS: switch to new multibus/multiadapter supportYing Zhang
- Added section "u_boot_list" in arch/powerpc/cpu/mpc85xx/u-boot-spl.lds - Use the function i2c_init_all instead of i2c_init Signed-off-by: Ying Zhang <b40530@freescale.com>
2013-09-07ppc4xx: Fix GPIO handling in lwmon5 and lcd4_lwmon5 BSPStefan Roese
LCD4 needs a slightly different GPIO configuration than the original LWMON5 variant. GPIO49 needs to be configured to a default output value of 0 (permanent voltage supply). Additionally lcd4 also needs to enable the LSB transmitter. Signed-off-by: Stefan Roese <sr@denx.de>
2013-09-06Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2013-09-06cam_enc_4xx: Move CONFIG_SPL_PAD_TO to a config headerMasahiro Yamada
For most boards which define CONFIG_SPL_PAD_TO, it is defined in config header files. Currently, there exists only one exception, cam_enc_4xx board. This patch moves CONFIG_SPL_PAD_TO definition from board/ait/cam_enc_4xx/config.mk to include/configs/cam_enc_4xx.h. With this modification, we can delete a glue code in the top level config.mk: ifneq ($(CONFIG_SPL_PAD_TO),) CPPFLAGS += -DCONFIG_SPL_PAD_TO=$(CONFIG_SPL_PAD_TO) endif Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Heiko Schocher <hs@denx.de>
2013-09-05Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
Conflicts: drivers/serial/serial.c The conflict above was a trivial case of adding one init function in each branch, and manually resolved in merge.
2013-09-04Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-09-04Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-09-03Merge 'u-boot-microblaze/zynq' into (u-boot-arm/master'Albert ARIBAUD
Conflicts: arch/arm/include/asm/arch-zynq/hardware.h The conflict above was trivial and solved during merge.
2013-08-31i.MX6: nitrogen6x: Don't bother setting PLL3(480) PFD1 divisorEric Nelson
This clock isn't feeding anything under U-Boot, so there's no point in changing it from power-on default. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-08-31ARM: Congatec: README updateSARTRE Leo
README: U-boot works both on SPI-NOR and SDcard Signed-off-by: Leo Sartre <lsartre@adeneo-embedded.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2013-08-30exynos5250: arndale: Add mmc supportInderpal Singh
This patch adds mmc support to the arndale board. Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-08-30exynos5250: Add arndale board supportChander Kashyap
Arndale board is based on samsung's exynos5250 soc. Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-08-28arm, am335x: add support for 3 siemens boardsHeiko Schocher
add support for the am335x based boards from siemens: dxr2: - DDR3 128MiB - NAND 256MiB - Ethernet with external Switch SMSC LAN9303 - no PMIC - internal Watchdog - DFU support pxm2: - DDR2 512 MiB - NAND 1024 MiB - PMIC - PHY atheros ar803x - USB Host - internal Watchdog - DFU support rut: - DDR3 256 MiB - NAND 256 MiB - PMIC - PHY natsemi dp83630 - external Watchdog - DFU support Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Cc: Pascal Bach <pascal.bach@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-08-28arm, am33xx: add defines for gmii_sel_register bitsHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-08-28am335x_evm: Update README for customizationTom Rini
As this is a reference platform, update the README to note which IP blocks are required for use due to design choices of the reference rather than required by the SoC itself. Signed-off-by: Tom Rini <trini@ti.com>
2013-08-28ARM: OMAP4460: sdp: Limit TPS mux config to 4460Taras Kondratiuk
TPS mux config is 4460 specific, so it should be limited to 4460 only. Signed-off-by: Taras Kondratiuk <taras@ti.com>
2013-08-28sdp4430: Initialize board id using CONFIG_MACH_TYPEOleksandr Tyshchenko
Use CONFIG_MACH_TYPE generic macro to set the machine type number in the common arm code instead of setting it in the board code. Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
2013-08-28arm: goni: remove config.mk fileMinkyu Kang
Since config.mk is deprecated, remove this file, and move CONFIG_SYS_TEXT_BASE define to config file. Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-08-28arm: smdkc100: remove config.mk fileMinkyu Kang
Since config.mk is deprecated, remove this file, and move CONFIG_SYS_TEXT_BASE define to config file. Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Cc: Wolfgang Denk <wd@denx.de>
2013-08-26ARM: OMAP5-uevm: Add usb device reset APIDan Murphy
Add the call back to reset the LAN9730 after the FEAT_POWER has been called. Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-08-26ARM: OMAP5-uevm: Add USB MAC ethernet addressDan Murphy
Set the usbethaddr based on the OMAP DIE_ID registers which should be unique for each processor. Then set this as the usb ethernet MAC address. Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-08-26ARM: OMAP5-uevm: Add USB ehci support for the uEVMDan Murphy
Add the USB ehci support for the OMAP5 uEVM. Configure the uEVM mux data Add the flags to build the appropriate modules Add the usb call backs to initialize the EHCI controller Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-08-26omap5: uevm: Change the board name to correct nameDan Murphy
Change the board name for the sys info to 5432 uEVM Signed-off-by: Dan Murphy <dmurphy@ti.com> Acked-by: Marek Vasut <marex@denx.de>
2013-08-22arm: atmel: remove the config.mk fileBo Shen
remove the config.mk file move text base define to board config file for following boards - at91sam9m10g45ek - at91sam9x5ek Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
generated by cgit (git 2.34.1) at 2024-12-27 13:58:42 +0000