summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)Author
2019-04-25tdx-cfg-block: add support for new colibri iMX6ull skusGerard Salvatella
Add support for new Colibri iMX6ULL SKUs. While at it also checkpatch fix the whole files. Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25colibri_vf: fix tab vs. spacesMarcel Ziswiler
Fix indentation using tab vs. spaces. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-25imx: support i.MX8QM MEK boardPeng Fan
Add i.MX8QM MEK board support. Included a basic dts, enabled SPL FIT Boot log as below: U-Boot SPL 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800) Normal Boot Trying to boot from MMC2_2 U-Boot 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800) CPU: NXP i.MX8QM RevB A53 at 142933 MHz Model: Freescale i.MX8QM MEK Board: iMX8QM MEK Build: SCFW 9330215b Boot: SD1 DRAM: 6 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000 Net: Error: ethernet@5b040000 address not set. eth-1: ethernet@5b040000 Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25boot.src: Provide dsa_core.blacklist bootarg when booting via NFSLukasz Majewski
This setup is a bit special as Linux kernel (4.19) is not supporting in-kernel NFS rootfs mount and Distributed Switch Architecture (DSA) operation. For that reason it was necessary to provide a bootarg to allow userspace enable it afterwards if needed. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: Remove EHCI specific code from HSC|DDC board fileLukasz Majewski
As EHCI on i.MX5 has been converted to driver model, the board specific code, necessary for VBUS USB power supply setup is not needed anymore. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: Remove non DM/DTS esdhc3 code from HSC|DDC board related filesLukasz Majewski
After switching to DM/DTS support of esdhc3 - the code in this patch can be removed. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: Remove HSC|DDC ETH PHY reset code after switching to DM/DTSLukasz Majewski
After commit efd0b791069a ("eth: dm: fec: Add gpio phy reset binding") the in-board file definition of ETH PHY reset can be removed. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25imx8qxp: mek: enable dm-spl for pmPeng Fan
with u-boot,dm-spl added for imx8qx-pm node, and SPL_SIMPLE_BUS enabled, the bind and probe code in board file could be removed. Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25arm: socfpga: move vining_fpga to DM_I2CSimon Goldschmidt
All socfpga boards except for vining_fpga use DM_I2C. Enable DM_I2C for this board and set the EEPROM defines via Kconfig (enabling CONFIG_I2C_EEPROM from MISC). Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Series-changes: 2 - added (this) patch to move socfpga_vining to DM_I2C
2019-04-25arm: socfpga: socrates: make rtc workSimon Goldschmidt
This patch makes the on-board RTC work on the socfpga_socrates board. This rtc is present on the board, but it does not work (fails with a timeout). This patch adds a weak pull-up on the I2C0-SCL pin connected to the m41t82 RTC on this board. While the SDA line has a pull-up on the pcb, the pull-up on the SCL line seems to be missing. To work around this, enable the weak-pull-up feature on this pin. After applying this patch, the rtc timeout is gone and the 'date' command can access the rtc chip. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
2019-04-24Merge tag 'pull-24apr19' of git://git.denx.de/u-boot-dmTom Rini
Various minor sandbox iumprovements Fixes for tracing with sandbox Refactoring for boot_get_fdt()
2019-04-24Merge tag 'u-boot-stm32-mcu-20190423' of https://github.com/pchotard/u-bootTom Rini
STM32 MCUs update: - DT rework and alignment with DT kernel v4.20 - mmc: arm_pl180_mmci: Synchronize compatible with kernel v4.20 - mmc: stm32_sdmmc2: Synchronize properties with kernel v4.20 - configs: update for F746/769 boards
2019-04-24Merge tag 'u-boot-amlogic-20190423' of git://git.denx.de/u-boot-amlogicTom Rini
- Add support for Amlogic p200 & p201 Reference Designs - Add Amlogic SoC information display - Add support for the Libretech-AC AML-S805X-AC board - Add Amlogic AXG reset compatible - Add I2C support for Amlogic AXG - Fix AXG PIN and BANK pinctrl definitions - Fix regmap_read_poll_timeout warning about sandbox_timer_add_offset - Add initial support for Amlogic G12A SoC and U200 board - Enable PHY_REALTEK for selected boards - Fix Khadas VIM2 README
2019-04-23sandbox: Move pre-console buffer out of the way of tracingSimon Glass
These two buffers currently conflict if tracing is enabled. Move the pre-console buffer and update the documentation. Signed-off-by: Simon Glass <sjg@chromium.org>
2019-04-23sandbox: Improve debugging in initcall_run_list()Simon Glass
At present if one of the initcalls fails on sandbox the address printing is not help, e.g.: initcall sequence 0000557678967c80 failed at call 00005576709dfe1f (err=-96) This is because U-Boot gets relocated high into memory and the relocation offset (gd->reloc_off) does not work correctly for sandbox. Add support for finding the base address of the text region (at least on Linux) and use that to set the relocation offset. This makes the output better: initcall sequence 0000560775957c80 failed at call 0000000000048134 (err=-96) Then you use can use grep to see which init call failed, e.g.: $ grep 0000000000048134 u-boot.map stdio_add_devices Of course another option is to run it with a debugger such as gdb: $ gdb u-boot ... (gdb) br initcall.h:41 Breakpoint 1 at 0x4db9d: initcall.h:41. (2 locations) Note that two locations are reported, since this function is used in both board_init_f() and board_init_r(). (gdb) r Starting program: /tmp/b/sandbox/u-boot [Thread debugging using libthread_db enabled] Using host libthread_db library "/lib/x86_64-linux-gnu/libthread_db.so.1". U-Boot 2018.09-00264-ge0c2ba9814-dirty (Sep 22 2018 - 12:21:46 -0600) DRAM: 128 MiB MMC: Breakpoint 1, initcall_run_list (init_sequence=0x5555559619e0 <init_sequence_f>) at /scratch/sglass/cosarm/src/third_party/u-boot/files/include/initcall.h:41 41 printf("initcall sequence %p failed at call %p (err=%d)\n", (gdb) print *init_fnc_ptr $1 = (const init_fnc_t) 0x55555559c114 <stdio_add_devices> (gdb) Signed-off-by: Simon Glass <sjg@chromium.org>
2019-04-23ARM: da850evm: Remove legacy MMC codeAdam Ford
With the migration to DM in SPL and the DT support, the old legacy code is no longer neaded, so this patch removes it Signed-off-by: Adam Ford <aford173@gmail.com>
2019-04-23board: stm32f746-disco: Get MII/RMII phy_mode from DTPatrice Chotard
This is needed to make ethernet work on stm32f746-eval which uses MII mode. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-04-23board: amlogic-q200: fix Khadas VIM2 READMENeil Armstrong
The vendor U-boot branch and defconfig was wrong for the Khadas VIM2, fix this. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-04-23boards: meson: add g12a u200Jerome Brunet
The Amlogic U200 board is based on the Amlogic S905D2 SoC from the Amlogic G12A SoC family. The board has the following specifications : - Amlogic S905D2 ARM Cortex-A53 quad-core SoC - XGB DDR4 SDRAM - 10/100 Ethernet (Internal PHY) - 1 x USB 3.0 Host - eMMC - SDcard - Infrared receiver - SDIO WiFi Module - MIPI DSI Connector - Audio HAT Connector - PCI-E M.2 Connector Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-04-23regmap: fix regmap_read_poll_timeout warning about sandbox_timer_add_offsetNeil Armstrong
When fixing sandbox test for regmap_read_poll_timeout(), the sandbox_timer_add_offset was introduced but only defined in sandbox code thus generating warnings when used out of sandbox : include/regmap.h:289:2: note: in expansion of macro 'regmap_read_poll_timeout_test' regmap_read_poll_timeout_test(map, addr, val, cond, sleep_us, \ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/spi/meson_spifc.c:169:8: note: in expansion of macro 'regmap_read_poll_timeout' ret = regmap_read_poll_timeout(spifc->regmap, REG_SLAVE, data, ^~~~~~~~~~~~~~~~~~~~~~~~ drivers/spi/meson_spifc.c: In function 'meson_spifc_txrx': include/regmap.h:277:4: warning: implicit declaration of function 'sandbox_timer_add_offset' [-Wimplicit-function-declaration] This fix adds a timer_test_add_offset() only defined in sandbox, and renames the previous sandbox_timer_add_offset() to it. Cc: Simon Glass <sjg@chromium.org> Reported-by: Tom Rini <trini@konsulko.com> Fixes: df9cf1cc08 ("test: dm: regmap: Fix the long test delay") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-04-22Merge tag 'u-boot-atmel-2019.07-b' of git://git.denx.de/u-boot-atmelTom Rini
Second set of u-boot-atmel features and fixes for 2019.07 cycle
2019-04-21stm32mp1: add stusb1600 support for DK1 and DK2 boardPatrick Delaunay
The DK1 and DK2 boards use the USB Type-C controller STUSB1600. This patch updates: - the device tree to add the I2C node in the DT - the board stm32mp1 to probe this I2C device and use this controller to check cable detection. - the DWC2 driver to support a new dt property "u-boot,force-b-session-valid" which forces B session and device mode; it is a workaround because the VBUS sensing and ID detection isn't available with stusb1600. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-21stm32mp1: migrate USBOTG device to driver modelPatrick Delaunay
Use the DWC2 device driver with DM_USB_GADGET support and cleanup the USB support in STM32MP1 board. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-18arm: dts: h6: Add Beelink GS1 initial supportClément Péron
Beelink GS1 is an Allwinner H6 based TV box, which support: - Allwinner H6 Quad-core 64-bit ARM Cortex-A53 - GPU Mali-T720 - 2GB LPDDR3 RAM - 16GB eMMC - AXP805 PMIC - 1Gbps GMAC via RTL8211E - USB 2.0 and 3.0 Host - HDMI port - S/PDIF port - 5V/2A DC power supply - Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS) Linux commit details about the sun50i-h6-beelink-gs1.dts sync: "arm64: dts: allwinner: h6: Introduce Beelink GS1 board" (sha1: 089bee8dd119ba084dee6b17a2e1a53df4f30193) Signed-off-by: Clément Péron <peron.clem@gmail.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-18Merge tag 'arc-for-2019.07' of git://git.denx.de/u-boot-arcTom Rini
In this small series we migrate ARC boards to DM_MMC so we're hopefully are good now and our boards will be kept in U-Boot for some more time :)
2019-04-18board: atmel: add SAMA5D2 ICP boardEugen Hristev
The SAMA5D2 ICP Board features the SAMA5D27 SoC, together with QSPI Flash, Wilc3000 wireless device and EtherCat support. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-04-18ARC: [plat-axs10x]: migrate to DM_MMCEugeniy Paltsev
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2019-04-18ARC: [plat-hsdk]: migrate to DM_MMCEugeniy Paltsev
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2019-04-17arm: am57xx: cl-som-am57x: remove board supportUri Mashiach
U-Boot support for the CL-SOM-AM57x module is no longer required. Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
2019-04-17Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
- Convert DM_MMC and DM_SCSI - A20, R40, H6 Linux dts(i) sync - CLK, RESET support for sunxi, sun8_emac net drivers
2019-04-17Merge tag 'xilinx-for-v2019.07' of git://git.denx.de/u-boot-microblazeTom Rini
Xilinx/FPGA changes for v2019.07 fpga: - Add support for external data in FIT - Extend testing for external data case - Inform user about a need to run post config on Zynq arm: - Tune zynq command functions - Fix internal variable setting arm64: - Add support for zc39dr decoding - Disable WDT for zcu100 - Small changes in reset_reason() - Some DT changes (spi) - Tune qspi-mini configuration - Remove useless eeprom setting - Fix two sdhci boot case spi: - Fix tap delay programming clk: - Enable i2c in SPL net: - Fix gem phydev handling - Remove phy detection code from gem driver general: - Correct EXT_DTB usage for MULTI_DTB_FIT configuration
2019-04-17sunxi: update SATA driver to always use DM_SCSIAndre Przywara
It seems like the Allwinner SATA driver is already quite capable of using the driver model, so we can force this on all boards and can remove support for a non-DM_SCSI build. This removes the warning about boards with SATA ports not being DM_SCSI compliant. It also takes the opportunity to move the driver out of the board/sunxi directory to join its siblings in drivers/ata, and to make it a proper Kconfig citizen. The board defconfigs stay untouched. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@openedev.com> [jagan: select DM_SCSI separately] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-17board: sunxi: Add R40 sata compatibleJagan Teki
Add sata compatible for R40. Cc: Pablo Sebastián Greco <pgreco@centosproject.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-16board: sunxi: gmac: Remove Ethernet clock and resetJagan Teki
Since Ethernet clock and reset is now handling via CLK and RESET frameworks via driver API's remove explicit ccm writes. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-16arm64: zynqmp: Add idcode for new RFSoC silicon ZU39DRSiva Durga Prasad Paladugu
This patch adds "zu39dr" to the list of zynqmp devices The zu39DR is the new RFSoC silicon with id value of 0x66. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16ARM: zynq: Check zynq aes & rsa command parameters countT Karthik Reddy
This patch checks for zynq aes & rsa commands max parameters count. Also checks minimum number of parameters count for aes command. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16arm64: zynqmp: Use zynqmp_mmio_read/write functionsT Karthik Reddy
Changed the return type of reset_reason() to int from u32, because zynqmp_mmio_read/write() returns signed value on error. Replaced readl and writel functions with zynqmp_mmio_read & zynqmp_mmio_write functions to access RESET_REASON(CRL_APB) registers. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-15Merge tag 'u-boot-imx-20190415' of git://git.denx.de/u-boot-imxTom Rini
Move to DM ----------- - DM support in sata - Toradex Board to DM - wandboard to DM - tbs2910 to DM - GE boards to DM - VHybrid boards to DM - DM_VIDEO for i.MX
2019-04-14Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
Conflicts: arch/arm/dts/armada-385-amc.dts arch/arm/dts/armada-xp-theadorable.dts arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-13imx: aristainetos: fix build breakageAnatolij Gustschin
ipu.h header is not found since the ipuv3 driver was moved to the drivers/video/imx subdirectory. Fix it. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13tdx-cfg-block: fix off by one issueMarcel Ziswiler
Fix toradex_modules array off by one issue potentially leading to spurious printout during boot e.g. Model: Toradex V1.2A, instead of Model: Toradex UNKNOWN MODULE V1.2A. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13toradex: common: unify behaviour when config block is missingBhuvanchandra DV
If the config block is missing, various things may fail or behave strangely on certain modules. This patch unifies that behaviour by using a fake MAC address, until user updates the config block. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13toradex: configblock: add an -y parameter to 'cfgblock create’Dominik Sliwa
Add an optional -y parameter to 'cfgblock create’ to simplify automation. Signed-off-by: Dominik Sliwa <dominik.sliwa@toradex.com> Acked-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13colibri_vf: use leveling evaluated by DDR validation toolsStefan Agner
The DDR validation tool (which is part of Processor Expert) allows to evaluate leveling parameters for CR105/CR106/CR110. Several runs have been made with Colibri VF50 and VF61 and it seems to evaluate very similar values. Use this values by default. Note: The newly evaluated parameters seem to require CTLUPD_AREF to be enabled! Note 2: The tool also evaluated 6 as a new value for PHY02/18 GATE_CFG (Coarse adjust of gate open time). However, this seems not to work in practise. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13colibri_vf: adjust timing according to data sheetStefan Agner
Using the DDR Validation tool in Processor Expert uncovered two timing inconsistencies. Since those timings are related to the suspend mode they do not affect or change regular memory behaviour. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13colibri_vf: sync the board info messageBhuvanchandra DV
Use similar info message as on other modules. Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13colibri_vf: migrate fec, esdhc, nfc and usb to driver modelMarcel Ziswiler
Migrate FEC, ESDHC, NFC and USB to driver model. While at it also do no longer enable optional I2C clock in board file as the generic clock code now handles this. Note for space reason and as it is not required just for booting we do not enable I2C in U-Boot by default. While at it also update copyright period. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13colibri_vf: migrate pinctrl and regulators to dtb/dmMarcel Ziswiler
Migrate pinctrl and regulators to device tree resp. driver model: DDR, DSPI, ENET, ESDHC, I2C, NFC and UART. Enable CMD_DM, PINCTRL and DM_REGULATOR. While at it also update copyright period and sort include files. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13ARM: dts: colibri_vf: update device treesMarcel Ziswiler
Update device tree in preparation of further driver model migration: Ethernet FEC, ESDHC aka MMC/SD card, I2C, NFC aka NAND flash controller, USBH_PEN GPIO regulator. Add iomux resp. pinctrl entries to be removed from proprietary platform data: DSPI, ESDHC, FEC, I2C, NFC, UART, USBH_PEN GPIO. Introduce a U-Boot specific device tree with some required u-boot,dm-pre-reloc properties: soc, aips0, pinctrl_ddr and uart0 incl. pinctrl. While at it also update the MAINTAINERS file. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13Add missing space in commentMarcel Ziswiler
Spotted two missing spaces in comments. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
generated by cgit (git 2.34.1) at 2025-01-30 22:11:56 +0000