| Age | Commit message (Collapse) | Author |
|---|
|
Right now enabling SPL_FRAMEWORK will also enable it for the TPL in all
cases, making the TPL bigger. There may be cases where the TPL is really
size constrained due to its underlying ram size.
Therefore introduce a new TPL_FRAMEWORK option and make the relevant
conditionals check for both. The default is set to "y if SPL_FRAMEWORK"
to mimic the previous behaviour where the TPL would always get the
SPL framework if it was enabled in SPL.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
|
|
Trusted-Firmware can also initialize a secure payload to use as a trusted
execution environment. In general for the arm64 case this is provided as
separate image and uboot is supposed to also place it in a predetermined
location in memory and add the necessary parameters to the ATF boot params.
So add the possibility to get this tee payload from the provided FIT image
and setup things as necessary.
Tested on a Rockchip PX30 with mainline TF-A, mainline OP-Tee (with pending
PX30 support) and mainline 5.4-rc1 Linux kernel.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
As SPL_SPI_FLASH_SUPPORT cannot work without SPL_SPI_SUPPORT, fix
dependencies to prevent enabling SPI flash support without basic SPI
support.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191104
-------------------
- i.MX NAND: nandbcb support for MX6UL / i.MX7
- i.MX8: support for HAB
- Convert to DM (opos6ul, mccmon6)
- Toradex i.MX6ull colibri
- sync DTS with kernel
Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/606853416
|
|
This commit adds falcon boot support (by also copying args necessary for
booting) to the SPL NOR memory driver.
After this change it is possible to use the falcon boot in the same way
as on NAND memories. The necessary configs (i.e. CONFIG_CMD_SPL_NOR_OFS)
are now defined in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
We have the ability to enforce a maximum size for SPL but not yet for TPL.
Add a new option for this.
Document the size check macro while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
- Fix for patman with email addresses containing commas
- Bootstage improvements for TPL, SPL
- Various sandbox and dm improvements and fixes
|
|
On i.MX8, when booting from eMMC boot partition, the whole flash.bin
is stored in boot partition, however SPL switches to user partition
during the init of mmc driver:
spl_mmc_load() -> mmc_init()
Then it tries to load the container image in
spl_mmc_get_uboot_raw_sector(), but here it reads the data from user
partition and the header is not recognized as a valid header.
So we move spl_mmc_get_uboot_raw_sector after eMMC partition switch
to address this issue.
Anyway put spl_mmc_get_uboot_raw_sector before eMMC partition switch
is not correct, so let's move it after eMMC partition switch.
Reported-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
It is possible to enable bootstage in TPL. TPL can stash the info for SPL.
But at present this information is then lost because SPL does not read
from the stash.
Add support for SPL not being the first phase to enable bootstage.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present bootstage in TPL and SPL use the same ID so it is not possible
to see the timing of each. Separate out the IDs and use the correct one
depending on which phase we are at.
Example output:
Timer summary in microseconds (14 records):
Mark Elapsed Stage
0 0 reset
224,787 224,787 TPL
282,248 57,461 end TPL
341,067 58,819 SPL
925,436 584,369 end SPL
931,710 6,274 board_init_f
1,035,482 103,772 board_init_r
1,387,852 352,370 main_loop
1,387,911 59 id=175
Accumulated time:
196 dm_r
8,300 dm_spl
14,139 dm_f
229,121 fsp-m
262,992 fsp-s
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Loading U-Boot on i.MX8QXP MEK board is broken since recent changes
in spl_mmc:
U-Boot SPL 2019.10-00162-gff5bd397e4 (Oct 18 2019 - 15:50:45 +0200)
Normal Boot
WDT: Not found!
Trying to boot from MMC2_2
Load image from MMC/SD 0x46400
spl: mmc partition switch failed
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The newly added CONFIG_SYS_MMCSD_RAW_MODE_EMMC_BOOT_PARTITION option
is selected automatically and overrides the EXT_CSC_PART_CONFIG
configurations with default value, always selecting the eMMC boot
partition 1. Boards which place U-Boot image in other partitions
became not bootable.
Fix this by making the eMMC HW boot partition selection optional.
Fixes: 17241ea0543a (spl: mmc: Add option to set eMMC HW boot partition)
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-mmc
- Add sdhci driver for Broadcom iProc platform
- Add a driver callback for power-cycle for mmc
- Implement host_power_cycle callback for stm32_sdmmc2
- spl: dm_mmc: Initialize only the required mmc device
|
|
- Assorted cleanups
- FAT bugfixes
- mediatek platform updates
|
|
This define indicates if DM_SPI shall be supported in SPL. This allows
proper operation of DM converted SPI drivers in SPL, which use
#if !CONFIG_IS_ENABLED(DM_SPI) to also support not yet DM/DTS converted
boards.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This change allows setting pre-defined eMMC boot partition for SPL eMMC
booting. It is necessary in the case when one wants to boot (through falcon
boot) from eMMC after loading SPL from other memory (like SPI-NOR).
Signed-off-by: Mans Rullgard <mans@mansr.com>
[lukma: Edit the commit message]
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
|
|
This fixes a wrongly indented block of code.
Signed-off-by: Mans Rullgard <mans@mansr.com>
[lukma: Make the commit message more verbose]
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This commit add a generic function board_init_f that
only initialize some device (for example serial). It
avoid to define a board function only to launch the
serial configuration.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
Expose SPL's Y-Modem core loader function via the common SPL header
file so it can be re-used for purposes other than loading U-Boot itself.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
|
|
During FIT reading through ymodem_read_fit() the function
xyzModem_stream_read() is being used which returns zero once the end
of a stream has been reached. This could lead to an premature exit from
ymodem_read_fit() with certain-sized FIT images reporting that zero
bytes overall were read. Such a premature exit would then result in an
-EIO failure being triggered within the spl_load_simple_fit() caller
function and ultimately lead to a boot failure.
Fix this logic by simply aborting the stream read loops and continuing
with the regular code flow which ultimately would lead to returning
the number of bytes to be read ('size') as expected by the callers of
ymodem_read_fit().
Fixes: fa715193c083 ("spl: Add an option to load a FIT containing U-Boot from UART")
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
|
|
In SPL, all the available mmc devices gets initialized during boot.
This might not work in cases where clocks are not available for
certain mmc devices(other than boot device) and the support for
enabling device might not be ready.
Texas Instruments' K3 J721E device having a central system controller
(dmsc) is one such example falling in this category. Below is the
sequence for the failing scenario:
- ROM comes up in SD mode and loads SPL by just initialing SD card.
- SPL loads dmsc firmware from SD Card.
Since ROM has enabled SD, SPL need not enable the SD, just need
to re initialize the card. But SPL is trying to initialize other MMC
instances which are in disabled state. Since dmsc firmware is not yet
available, devices cannot be enabled. So in SPL, initialize only the
mmc device that is needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx/FPGA changes for v2020.01
FPGA:
- Enable fpga loading on Versal
- Minor fix
Microblaze:
- Fix LMB configurations to support initrds
- Some other cleanups
Zynq:
- Minor config/dt changes
- Add distro boot support for usb1 and mmc1
- Remove Xilinx private boot commands and use only distro boot
ZynqMP:
- Kconfig cleanups, defconfig updates
- Update some dt files
- Add firmware driver for talking to PMUFW
- Extend distro boot support for jtag
- Add new IDs
- Add system controller configurations
- Convert code to talk firmware via mailbox or SMCs
Versal:
- Add board_late_init()
- Add run time DT memory setup
- Add DFU support
- Extend distro boot support for jtag and dfu
- Add clock driver
- Tune mini configurations
Xilinx:
- Improve documentation (boot scripts, dt binding)
- Enable run time initrd_high calculation
- Define default SYS_PROMPT
- Add zynq/zynqmp virtual defconfig
Drivers:
- Add Xilinx mailbox driver for talking to firmware
- Clean zynq_gem for Versal
- Move ZYNQ_HISPD_BROKEN to Kconfig
- Wire genphy_init() in phy.c
- Add Xilinx gii2rgmii bridge
- Cleanup zynq_sdhci
- dwc3 fix
- zynq_gpio fix
- axi_emac fix
Others:
- apalis-tk1 - clean config file
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191009
-------------------
Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/595148532
- MX6UL / ULZ
- Toradex board
- Allow to set OCRAM for MX6Q/D
- MX7ULP
- MX8: (container image, imx8mq_mek), SCU API
- fix several board booting from SD/EMMC (cubox-i for example)
- pico boards
[trini: display5 merged manually]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
i.MX8 only support AHAB secure boot with Container format image,
we could not use FIT to support secure boot, so introduce container
support to let SPL could load container images.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8 only support AHAB secure boot with Container format image,
we could not use FIT to support secure boot, so introduce container
support to let SPL could load container images.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
i.MX8 only support AHAB secure boot with Container format image,
we could not use FIT to support secure boot, so introduce container
support to let SPL could load container images.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Introduce weak spl_nand_get_uboot_raw_page, then platform could
have their own implementation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Andreas Dannenberg <dannenberg@ti.com>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Michal Simek <michal.simek@xilinx.com>
|
|
Introduce weak spl_nor_get_uboot_base, then platform have their own
implementation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Andreas Dannenberg <dannenberg@ti.com>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Michal Simek <michal.simek@xilinx.com>
|
|
Introduce a weak function spl_spi_get_uboot_offs, then
platform could have their own implementation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Andreas Dannenberg <dannenberg@ti.com>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Michal Simek <michal.simek@xilinx.com>
|
|
Introduce a weak function spl_mmc_get_uboot_raw_sector, then platform
could have their own implementation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Andreas Dannenberg <dannenberg@ti.com>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Michal Simek <michal.simek@xilinx.com>
|
|
This change tries to fix the following problem:
- The board boots (to be more precise - ROM loads SPL) from a slow SPI-NOR
memory.
As a result the spl_boot_device() will return SPI-NOR as a boot device
(which is correct).
- The problem is that in 'falcon boot' the eMMC is used as a boot medium to
load kernel from its partition.
Calling spl_boot_device() will break things as it returns SPI-NOR device.
To fix this issue the new CONFIG_SPL_FORCE_MMC_BOOT Kconfig flag is
introduced to handle this special use case. By default it is not defined,
so there is no change in the legacy code flow.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
i.MX8 only support AHAB secure boot with Container format image,
we could not use FIT to support secure boot, so introduce container
support to let SPL could load container images.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Previously the SPL size on all iMX6 platforms was restricted to 68KB
because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
other iMX6 variants have 256KB of OCRAM. Add an option
CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
don't need to support the SL/DL variants. This allows for an SPL size of
196KB, which makes it much easier to use configurations such as SPL with
driver model and FDT control.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
|
|
Pass spl_image and bootdev to board_return_bootrom.
i.MX8MN needs the args to let ROM to load images
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Define default address via Kconfig. There is no need to change this address
for most of the boards but it is also possible. This one line save a lot of
lines in defconfigs that's why make sense to do it.
The similar change has been done by commit 9340d8fe8beb
("sunxi: move CONFIG_SPL_TEXT_BASE from *_defconfig to Kconfig")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
|
|
This is currently a decimal value which is not as convenient or
meaningful. Also U-Boot tends to use hex everywhere.
Convert this option to hex and add a comment for the size_check macro.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the typo in the commit title]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present there is only one control for this and it is used for both SPL
and TPL. But SPL might have a lot more space than TPL so the extra cost of
a full printf() might be acceptable.
Split the option into two, providing separate SPL and TPL controls. The
TPL setting defaults to the same as SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present the bloblist is set up in spl_common_init() which can be called
from spl_early_init(), i.e. before SDRAM is ready. This prevents the
bloblist from being located in SDRAM, which is useful on some platforms
where SRAM is inaccessible after U-Boot relocates (e.g. x86 CAR region).
It doesn't serve much purpose to have the bloblist available early, since
very little is known about the platform then, and the handoff info is
written when SPL is about to jump to U-Boot.
Move the code to board_init_r() to avoid any restrictions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present there is an arch-specific area in the SPL handoff area intended
for use by arch-specific code, but there is no explicit call to fill in
this data. Add a hook for this.
Also use the hook to remove the sandbox-specific test code from
write_spl_handoff().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present these options can be enabled when bloblist is not enabled for
SPL or TPL. This is incorrect as SPL handoff requires bloblist. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
- Assorted minor bugfixes
|
|
Several options are presenting themselves on a various boards
where the options are clearly not used. (ie, SPL/TPL options
when SPL or TPL are not defined)
This patch is not attempting to be a complete list of items, but
more like low hanging fruit. In some instances, I wasn't sure
of DM was required, so I simply made them SPL or TPL.
This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
- Support SPL and OpenSBI (FW_DYNAMIC firmware) boot.
- Fix qemu kconfig build warning.
|
|
To support relocation of the stack and global data on RISC-V, the
secondary harts must be notified of the change using IPIs. We can reuse
the hart relocation code for this purpose. It uses global data to store
the new stack pointer and global data pointer for the secondary harts.
This means that we cannot update the global data pointer of the main
hart in spl_relocate_stack_gd(), because the secondary harts have not
yet been relocated at this point. It is updated after the secondary
harts have been notified.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
RISC-V OpenSBI is an open-source implementation of the RISC-V Supervisor
Binary Interface (SBI) specification. It is required by Linux and U-Boot
running in supervisor mode. This patch adds support for booting via the
OpenSBI FW_DYNAMIC firmware. It supports OpenSBI version 0.4 and higher.
In this configuration, U-Boot SPL starts in machine mode. After loading
OpenSBI and U-Boot proper, it will start OpenSBI. All necessary
parameters are generated by U-Boot SPL and are passed to OpenSBI. U-Boot
proper is started in supervisor mode by OpenSBI. Support for OpenSBI is
enabled with CONFIG_SPL_OPENSBI. An additional configuration entry,
CONFIG_SPL_OPENSBI_LOAD_ADDR, is used to specify the load address of the
OpenSBI firmware binary. It is not used directly in U-Boot and instead
is intended to make the value available to scripts such as FIT
configuration generators.
The header file include/opensbi.h is based on header files from the
OpenSBI project. They are recent, as of commit bae54f764570 ("firmware:
Add fw_dynamic firmware").
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
As part of the SPL FIT boot flow, the device tree is appended to U-Boot
proper. The device tree is used to record information on the loadables
to make them available to the SPL framework and U-Boot proper. Depending
on the U-Boot device tree provider, the FIT image might not include a
device tree. Information on the loadables is missing in this case.
When booting via firmware bundled with the FIT image, U-Boot SPL loads
the firmware binary and U-Boot proper before starting the firmware. The
firmware, in turn, is responsible for starting U-Boot proper.
Information on the memory location of the U-Boot proper loadable must be
available to the SPL framework so that it can be passed to the firmware
binary. To support this use case when no device tree is found in the FIT
image, fall back to the U-Boot device tree in this situation.
At the same time, update the comment to remove the note that the
destination address must be aligned to ARCH_DMA_MINALIGN. Alignment is
only required as an intermediate step when reading external data. This
is automatically handled by spl_fit_append_fdt(). After reading the
external data, it is copied to the specified address, which does not
have to be aligned to ARCH_DMA_MINALIGN.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_SPI_U_BOOT_OFFS
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
[trini: Expose this for SPL_SPI_SUNXI for now]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Several options are presenting themselves on a various boards
where the options are clearly not used. (ie, arm64 options on
arm9, or SPL/TPL options when SPL or TPL are not defined)
This patch is not attempting to be a complete list of items, but
more like low hanging fruit.
This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
