| Age | Commit message (Collapse) | Author |
|---|
|
* Fix setting of ESDMODE (MR1) register - the bit shifting was wrong
* Fix the format string to match size in a debug print
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The ddr_pd_cntl isn't defined in any reference manual and thus we wil
remove especially since we set it to 0, which would most likely be its
POR value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The ddr code computes most things as 64-bit quantities and had some places
in the middle that it was using phy_addr_t and phys_size_t.
Instead we use unsigned long long through out and only at the last stage of
setting the LAWs and reporting the amount of memory to the board code do we
truncate down to what we can cover via phys_size_t.
This has the added benefit that the DDR controller itself is always setup
the same way regardless of how much memory we have. Its only the LAW
setup that limits what is visible to the system.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
- support mirrored DIMMs, not support register DIMMs
- test passed on P2020DS board with MT9JSF12872AY-1G1D1
- test passed on MPC8569MDS board with MT8JSF12864HY-1G1D1
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Travis Wheatley <travis.wheatley@freescale.com>
|
|
1. wr_lat
UM said the total write latency for DDR2 is equal to
WR_LAT + ADD_LAT, the write latency is CL + ADD_LAT - 1.
so, the WR_LAT = CL - 1;
2. rd_to_pre
we missed to add the ADD_LAT for DDR2 case.
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
Some 85xx processors have the advanced power management feature,
such as wake up ARP, that needs enable the automatic self refresh.
If the DDR controller pass the SR_IT (self refresh idle threshold)
idle cycles, it will automatically enter self refresh. However,
anytime one transaction is issued to the DDR controller, it will
reset the counter and exit self refresh state.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
|
|
- The DDR3 controller is expanding the bits for timing config
- Add the DDR3 32-bit bus mode support
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
|
|
According to the latest 8572 UM, the DDR3 controller
is expanding the bit mask, and we use the extend ACTTOPRE
mode when tRAS more than 19 MCLK.
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
|
|
Fix some bugs:
1. Correctly set intlv_ctl in cs_config.
2. Correctly set sa, ea in cs_bnds when bank interleaving mode is enabled.
3. Set base_address and total memory for each ddr controller in memory
controller interleaving mode.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
|
|
ctrl_regs.c: In function 'compute_fsl_memctl_config_regs':
ctrl_regs.c:523: warning: 'caslat' may be used uninitialized in this function
ctrl_regs.c:523: note: 'caslat' was declared here
Add a warning in DDR1 case if cas_latency isn't a value we know about.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
The main purpose of this rewrite it to be able to share the same
initialization code on all FSL PowerPC products that have DDR
controllers. (83xx, 85xx, 86xx).
The code is broken up into the following steps:
GET_SPD
COMPUTE_DIMM_PARMS
COMPUTE_COMMON_PARMS
GATHER_OPTS
ASSIGN_ADDRESSES
COMPUTE_REGS
PROGRAM_REGS
This allows us to share more code an easily allow for board specific code
overrides.
Additionally this code base adds support for >4G of DDR and provides a
foundation for supporting interleaving on processors with more than one
controller.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
