| Age | Commit message (Collapse) | Author |
|---|
|
Enhance do_bootm_vxworks() to support Linux compatible standard DTB
for ARM and PPC, when the least significant bit of flags in VxWorks
bootargs is set. Otherwise it falls back to the existing bootm flow
which is now legacy.
Signed-off-by: Lihua Zhao <lihua.zhao@windriver.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
|
|
Add build documentation for rk3308 based boards.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
|
|
support parse regulator standard property:
regulator-off-in-suspend;
regulator-init-microvolt;
regulator-suspend-microvolt:
regulator_get_suspend_enable
regulator_set_suspend_enable
regulator_get_suspend_value
regulator_set_suspend_value
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Rename the CONFIG_SECURE_BOOT name to CONFIG_NXP_ESBC to avoid
conflicts with UEFI secure boot.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
- DFU updates
- USB Storage updates
|
|
Add a note about the driver name in the of-platdata documentation since
the naming must follow the compatible string.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add optional parameter to 'avb verify' sub-command, so that user is able
to specify which slot to use, in case when user's partitions are
slotted. If that parameter is omitted, the behavior of 'avb verify' will
be the same as before, so user API is content.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Acked-by: Igor Opaniuk <igor.opaniuk@gmail.com>
|
|
Add weak callback to allow board specific behavior
- flush
- initiated
This patch prepare usage of DFU back end for communication with
STM32CubeProgrammer on stm32mp1 platform with stm32prog command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add a virtual DFU backend to allow board specific read and write
(for OTP update for example).
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add the support of MTD partition for the MTD backend.
The expected dfu_alt_info for one alternate on the mtd device :
<name> part <part_id>
<name> partubi <part_id>
"partubi" also erase up to the end of the partition after write operation.
For example: dfu_alt_info = "spl part 1;u-boot part 2; UBI partubi 3"
U-Boot> dfu 0 mtd nand0
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add DFU backend for MTD device: allow to read
and write on all MTD device (NAND, SPI-NOR,
SPI-NAND,...)
For example :
> set dfu_alt_info "nand_raw raw 0x0 0x100000"
> dfu 0 mtd nand0
This MTD backend provides the same level than dfu nand
backend for NAND and dfu sf backend for SPI-NOR;
So it can replace booth of them but it also
add support of spi-nand.
> set dfu_alt_info "nand_raw raw 0x0 0x100000"
> dfu 0 mtd spi-nand0
The backend code is based on the "mtd" command
introduced by commit 5db66b3aee6f ("cmd: mtd:
add 'mtd' command")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add support of DFU for several interface/device
with one command.
The format for "dfu_alt_info" in this case is :
- <interface> <dev>'='alternate list (';' separated)
- each interface is separated by '&'
The previous behavior is always supported.
One example for NOR (bootloaders) + NAND (rootfs in UBI):
U-Boot> env set dfu_alt_info \
"sf 0:0:10000000:0=spl part 0 1;u-boot part 0 2; \
u-boot-env part 0 3&nand 0=UBI partubi 0,3"
U-Boot> dfu 0 list
DFU alt settings list:
dev: SF alt: 0 name: spl layout: RAW_ADDR
dev: SF alt: 1 name: ssbl layout: RAW_ADDR
dev: SF alt: 2 name: u-boot-env layout: RAW_ADDR
dev: NAND alt: 3 name: UBI layout: RAW_ADDR
U-Boot> dfu 0
$> dfu-util -l
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=3, name="UBI", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=2, name="u-boot-env", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=1, name="u-boot", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=0, name="spl", serial="002700333338511934383330"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Copy the partition support from NAND backend to SF,
support part and partubi option.
In case of ubi partition, erase the rest of the
partition as it is mandatory for UBI.
The added code is under compilation flag CONFIG_DFU_SF_PART
activated by default.
for example:
U-Boot> env set dfu_alt_info "spl part 0 1;\
u-boot part 0 2;u-boot-env part 0 3;UBI partubi 0 4"
U-Boot> dfu 0 sf 0:0:10000000:0
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add documentation for dfu stack and "dfu" command.
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
- Clean up Travis-CI slightly and then add support for Microsoft Azure
pipelines, all from Bin Meng.
|
|
- H6 dts(i) sync (Clément)
- H6 PIO (Icenowy)
- Fix pll1 clock calculation (Stefan)
- H6 dram, half DQ (Jernej)
- A64 OLinuXino eMMC (Sunil)
|
|
This adds a reST document for how to build U-Boot host tools,
including information for both Linux and Windows.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add DT binding documentation for DDR sub system present on J721E device.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
We need distinguish the following two situations in various SPI APIs:
- given chip select num is invalid
- given chip select num is valid, but no device is attached
Currently -ENODEV is returned for both cases.
For the first case, it's more reasonable to return -EINVAL instead of
-ENODEV for invalid chip select numbers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
If an SPI controller driver does not implement ops->cs_info, that
probably means any chip select number could be valid, hence let's
return 0 for spi_cs_info().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
ubi enhancements for 2020.01
- provide a way for skipping crc checks ported from linux, and add an
U-Boot command to set this flag on already installed systems.
- fix redundand environment management
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-dm
binman enhancements:
- Dropping some test Elf files and building them from source instead
- Refactoring of x86 16-bit entries
- Support for SPL symbols within sections
- Handle the 'notes' sections and hidden symbols in recent binutils
- Improved error reporting with a tool fails
libfdt and documentation fixes
vboot required-key test
driver model power-domain controls
patman Message-Id enhancement
|
|
Fully take over the ARM maintainers entry.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
U-Boot now supports the "skip_check" flag to optionally skip the CRC
check at open time. Currently its only possible to set this bit upon
UBI volume creation. But it might be very useful to also set this bit
on already installed systems (e.g. field upgrade) to make also use of
the boot-time decrease on those systems.
This patch now adds a new "ubi" command "ubi skipcheck" to set or clear
this bit in the UBI volume header:
=> ubi skipcheck rootfs0 on
Setting skip_check on volume rootfs0
BTW: This saves approx. 10 seconds Linux bootup time on a MT7688 based
target with 128MiB of SPI NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Dannenberg <dannenberg@ti.com>
|
|
Make it a little easier to find the documentation.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
- Assorted cleanups
- FAT bugfixes
- mediatek platform updates
|
|
At this point, all drivers that do not use CONFIG_BLK are past their
migration deadlines, so remove this config as it's no longer helpful and
hinders enhancing block drivers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add support for CDCE913/925/937/949 family of devices. These are modular
PLL-based low cost, high performance, programmable clock synthesizers,
multipliers and dividers. They generate up to 9 output clocks from a
single input frequency. The initial version of the driver does not
support programming of the PLLs, and thus they run in the bypass mode
only. The code is loosely based on the linux kernel cdce9xx driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
This adds a document for tphy which supports physical layer
functionality for a number of controllers on MediaTek SoCs,
such as, USB2.0, USB3.0, PCIe, and SATA.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
|
|
This adds a document for MT7623 PCIe controller.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
|
|
Some Texas Instruments K3 family of SoCs have one of more Digital Signal
Processor (DSP) subsystems that are comprised of either a TMS320C66x
CorePac and/or a next-generation TMS320C71x CorePac processor subsystem.
Add the device tree bindings document for the C66x DSP devices on these
SoCs. The added example illustrates the DT nodes for the first C66x DSP
device present on the K3 J721E family of SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The Texas Instruments K3 family of SoCs have one of more dual-core
Arm Cortex R5F processor subsystems/clusters (R5FSS). Add the device
tree bindings document for these R5F subsystem devices. These R5F
processors do not have an MMU, and so require fixed memory carveout
regions matching the firmware image addresses. The nodes require more
than one memory region, with the first memory region used for DMA
allocations at runtime. The remaining memory regions are reserved
and are used for the loading and running of the R5F remote processors.
The added example illustrates the DT nodes for the single R5FSS device
present on K3 AM65x family of SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx/FPGA changes for v2020.01
FPGA:
- Enable fpga loading on Versal
- Minor fix
Microblaze:
- Fix LMB configurations to support initrds
- Some other cleanups
Zynq:
- Minor config/dt changes
- Add distro boot support for usb1 and mmc1
- Remove Xilinx private boot commands and use only distro boot
ZynqMP:
- Kconfig cleanups, defconfig updates
- Update some dt files
- Add firmware driver for talking to PMUFW
- Extend distro boot support for jtag
- Add new IDs
- Add system controller configurations
- Convert code to talk firmware via mailbox or SMCs
Versal:
- Add board_late_init()
- Add run time DT memory setup
- Add DFU support
- Extend distro boot support for jtag and dfu
- Add clock driver
- Tune mini configurations
Xilinx:
- Improve documentation (boot scripts, dt binding)
- Enable run time initrd_high calculation
- Define default SYS_PROMPT
- Add zynq/zynqmp virtual defconfig
Drivers:
- Add Xilinx mailbox driver for talking to firmware
- Clean zynq_gem for Versal
- Move ZYNQ_HISPD_BROKEN to Kconfig
- Wire genphy_init() in phy.c
- Add Xilinx gii2rgmii bridge
- Cleanup zynq_sdhci
- dwc3 fix
- zynq_gpio fix
- axi_emac fix
Others:
- apalis-tk1 - clean config file
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191009
-------------------
Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/595148532
- MX6UL / ULZ
- Toradex board
- Allow to set OCRAM for MX6Q/D
- MX7ULP
- MX8: (container image, imx8mq_mek), SCU API
- fix several board booting from SD/EMMC (cubox-i for example)
- pico boards
[trini: display5 merged manually]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
The Denx FTP location is no longer reachable.
Switch to the Timesys repository instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
|
|
Introduce i.MX8 container set configuration file and add example
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Devicetree bindings are already specified in Linux kernel documentation.
Instead of maintaining same dt bindings in U-Boot doc specify path to dt
bindings in Linux kernel & documenting specific changes that are in U-Boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Fix these spelling errors the header file and documentation.
Fix a small typo in the PCI documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Sandbox pci works using emulation drivers which are currently children of
the pci device:
pci-controller {
pci@1f,0 {
compatible = "pci-generic";
reg = <0xf800 0 0 0 0>;
emul@1f,0 {
compatible = "sandbox,swap-case";
};
};
};
In this case the emulation device is attached to pci device on address
f800 (device 1f, function 0) and provides the swap-case functionality.
However this is not ideal, since every device on a PCI bus has a child
device. This is only really the case for sandbox, but we want to avoid
special-case code for sandbox.
Worse, child devices cannot be probed before their parents. This forces
us to use 'find' rather than 'get' to obtain the emulator device. In fact
the emulator devices are never probed. There is code in
sandbox_pci_emul_post_probe() which tries to track when emulators are
active, but at present this does not work.
A better approach seems to be to add a separate node elsewhere in the
device tree, an 'emulation parent'. This could be given a bogus address
(such as -1) to hide the emulators away from the 'pci' command, but it
seems better to keep it at the root node to avoid such hacks.
Then we can use a phandle to point from the device to the correct
emulator, and only on sandbox. The code to find an emulator does not
interfere with normal pci operation.
Add a new UCLASS_PCI_EMUL_PARENT uclass which allows finding an emulator
given a bus, and finding a bus given an emulator. Update the existing
device trees and the code for finding an emulator.
This brings PCI emulators more into line with I2C.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix 3 typos in the commit message;
encode bus number in the labels of swap_case_emul nodes;
mention commit 4345998ae9df in sandbox_pci_get_emul()]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
U-Boot already supports using -D to indicate that it should use the normal
device tree. It is sometimes useful to run with the test device tree, e.g.
when running a test. Add a -T option for this along with some
documentation.
It can be used like this:
/tmp/b/sandbox/u-boot -T -c "ut dm pci_busdev"
(this will use /tmp/b/sandbox/arch/sandbox/dts/test.dtb as the DT)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Sometimes devices don't appear and it can be confusing. Add a few notes to
help with this situation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix 2 issues in the doc and include the doc in the index.rst]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This updates MAINTAINERS and git-mailrc to add me as maintainer for
socfpga.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
For many sub-systems we already require the driver model to be used. Yet
there is still a handful of boards that do not have CONFIG_DM enabled.
We should make CONFIG_DM compulsory with release v2020.01
Conversion dates for CONFIG_DM_SPL and CONFIG_DM_TPL are yet to be defined.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The README.scrapyard file has been inconsistently updated. While well
intentioned, bad data is worse than no data, and in this case a pointer
to use the history that git provides. Remove the current content and
the script that would update it from time to time as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The of-plat.rst file till this change has been using
This is at best misleading as SPL_OF_PLATDATA is always defined when we
want to use this SPL tinification feature (also in U-Boot proper).
As a result the OF_PLATDATA SPL specific code is also compiled in when
U-Boot proper is build.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Update SPI drivers, driver model conversion status for
v2019.10 release.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Change maintainers to Priyanka Jain for fsl-qoriq, mpc85xx
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
|
