summaryrefslogtreecommitdiff
path: root/drivers/mmc/omap_hsmmc.c
AgeCommit message (Collapse)Author
2018-02-19mmc: Fix uninitialised priv memberAlex Kiernan
When using omap_hsmmc without the device model then the allocation of mmc->priv ends up uninitialised. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Tested-by: Robert Nelson <robertcnelson@gmail.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
2018-02-19mmc: omap_hsmmc: add signal voltage selection supportJean-Jacques Hiblot
I/O data lines of UHS SD card operates at 1.8V when in UHS speed mode (same is true for eMMC in DDR and HS200 modes). Add support to switch signal voltage to 1.8V in order to support UHS cards and eMMC HS200 and DDR modes. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19mmc: omap_hsmmc: allow mmc clock to be gatedKishon Vijay Abraham I
mmc core has defined a new parameter *clk_disable* to gate the clock. Disable the clock here if *clk_disable* is set. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19mmc: omap_hsmmc: implement send_init_stream callbackJean-Jacques Hiblot
This callback is used to send the 74 clock cycles after power up. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19mmc: omap_hsmmc: update mmc->clock with the actual bus speedJean-Jacques Hiblot
When the clock is applied, compute the actual value of the clock. It may be slightly different from the requested value (max freq, divisor threshold) Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19mmc: omap_hsmmc: allow the simple HS modes to use the default pinctrlJean-Jacques Hiblot
The default configuration is usually working fine for the the HS modes. Don't enforce the presence of a dedicated pinmux for the HS modes. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19mmc: omap_hsmmc: Add support to get pinctrl values and max frequency for ↵Kishon Vijay Abraham I
different hw revisions AM572x SR1.1 requires different IODelay values to be used than that used in AM572x SR2.0. These values are populated in device tree. Add capability in omap_hsmmc driver to extract IOdelay values for different silicon revision. The maximum frequency is also reduced when using a ES1.1. To keep the ability to boot both revsions with the same dtb, those values can be provided by the platform code. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19mmc: omap_hsmmc: Add support to set IODELAY valuesKishon Vijay Abraham I
The data manual of J6/J6 Eco recommends to set different IODELAY values depending on the mode in which the MMC/SD is enumerated in order to ensure IO timings are met. Add support to parse mux values and iodelay values from device tree and set these depending on the enumerated MMC mode. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19mmc: omap_hsmmc: use mmc_of_parse to populate mmc_configKishon Vijay Abraham I
Use the mmc_of_parse library function to populate mmc_config instead of repeating the same code in host controller driver. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19mmc: omap_hsmmc: Reduce the max timeout for reset controller fsmJean-Jacques Hiblot
>From OMAP3 SoCs (OMAP3, OMAP4, OMAP5, AM572x, AM571x), the DAT/CMD lines reset procedure section in TRM suggests to first poll the SRD/SRC bit until it is set to 0x1. But looks like that bit is never set to 1 and there is an observable delay of 1sec everytime the driver tries to reset DAT/CMD. (The same is observed in linux kernel). Reduce the time the driver waits for the controller to set the SRC/SRD bits to 1 so that there is no observable delay. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19mmc: omap_hsmmc: Workaround for errata id i802Jean-Jacques Hiblot
According to errata i802, DCRC error interrupts (MMCHS_STAT[21] DCRC=0x1) can occur during the tuning procedure. The DCRC interrupt, occurs when the last tuning block fails (the last ratio tested). The delay from CRC check until the interrupt is asserted is bigger than the delay until assertion of the tuning end flag. Assertion of tuning end flag is what masks the interrupts. Because of this race, an erroneous DCRC interrupt occurs. The suggested workaround is to disable DCRC interrupts during the tuning procedure which is implemented here. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19mmc: omap_hsmmc: Add tuning supportJean-Jacques Hiblot
HS200/SDR104 requires tuning command to be sent to the card. Use the mmc_send_tuning library function to send the tuning command and configure the internal DLL. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19mmc: omap_hsmmc: Enable DDR mode supportKishon Vijay Abraham I
In order to enable DDR mode, Dual Data Rate mode bit has to be set in MMCHS_CON register. Set it here. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19mmc: omap_hsmmc: set MMC mode in the UHSMS bit fieldJean-Jacques Hiblot
Use the timing parameter set in the MMC core to set the mode in UHSMS bit field. This is in preparation for adding HS200 support in omap hsmmc driver. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19mmc: omap_hsmmc: add support to set default io voltageKishon Vijay Abraham I
"ti,dual-volt" is used in linux kernel to set the voltage capabilities. For host controller dt nodes that doesn't have "ti,dual-volt", it's assumed 1.8v is the io voltage. This is not always true (like in the case of beagle-x15 where the io lines are connected to 3.3v). Hence if "no-1-8-v" property is set, io voltage will be set to 3v. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19mmc: omap_hsmmc: cleanup omap_hsmmc_set_iosKishon Vijay Abraham I
No functional change. Move bus width configuration setting to a separate function and invoke it only if there is a change in the bus width. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19mmc: omap_hsmmc: cleanup clock configurationJean-Jacques Hiblot
Add a separate function for starting the clock, stopping the clock and setting the clock. Starting the clock and stopping the clock can be used irrespective of setting the clock (For example during iodelay recalibration). Also set the clock only if there is a change in frequency. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-19mmc: omap_hsmmc: Fix incorrect bit operations for disabling a bitKishon Vijay Abraham I
omap_hsmmc driver uses "|" in a couple of places for disabling a bit. While it's okay to use it in "mmc_reg_out" (since mmc_reg_out has a _mask_ argument to take care of resetting a bit), it's incorrectly used for resetting flags in "omap_hsmmc_send_cmd". Fix it here by using "&= ~()" to reset a bit. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-19mmc: omap_hsmmc: Enable Auto command (CMD12) enableKishon Vijay Abraham I
Instead of sending STOP TRANSMISSION command from MMC core, enable the auto command feature so that the Host Controller issues CMD12 automatically when last block transfer is completed. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-19mmc: omap_hsmmc: Add support for DMA (ADMA2)Kishon Vijay Abraham I
The omap hsmmc host controller can have the ADMA2 feature. It brings better read and write throughput. On most SOC, the capability is read from the hl_hwinfo register. On OMAP3, DMA support is compiled out. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-18Revert "omap_hsmmc: update struct hsmmc to accommodate omap3 from DT"Jean-Jacques Hiblot
This reverts commit 46831c1a4cda75d92f7ad18d4e2b1eb196c62b2f. This reserved area at the beginning of struct hsmm, will be used later to support ADMA Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-01-12mmc: sanitize includes for DM i2cFelix Brack
This patch fixes some warnings when building boards that do not define DM_I2C_COMPAT i.e. boards that entirely rely on the new i2c layer. Signed-off-by: Felix Brack <fb@ltec.ch>
2017-08-01dm: mmc: Allow disabling driver model in SPLSimon Glass
At present if U-Boot proper uses driver model for MMC, then SPL has to also. While this is desirable, it places a significant barrier to moving to driver model in some cases. For example, with a space-constrained SPL it may be necessary to enable CONFIG_SPL_OF_PLATDATA which involves adjusting some drivers. Add new SPL versions of the options for DM_MMC, DM_MMC_OPS and BLK. By default these follow their non-SPL versions, but this can be changed by boards which need it. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01dm: Rename dev_addr..() functionsSimon Glass
These support the flat device tree. We want to use the dev_read_..() prefix for functions that support both flat tree and live tree. So rename the existing functions to avoid confusion. In the end we will have: 1. dev_read_addr...() - works on devices, supports flat/live tree 2. devfdt_get_addr...() - current functions, flat tree only 3. of_get_address() etc. - new functions, live tree only All drivers will be written to use 1. That function will in turn call either 2 or 3 depending on whether the flat or live tree is in use. Note this involves changing some dead code - the imx_lpi2c.c file. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-15drivers: omap_hsmmc: move to DM_MMC_OPSJean-Jacques Hiblot
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-11dm: mmc: omap_hsmmc: Add pre-reloc flag to the driverLokesh Vutla
For platforms that don't use device tree in SPL the only way to mark this driver as 'required by relocation' is with the DM_FLAG_PRE_RELOC flag. Add this to ensure that the driver is bound. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-05-11dm: mmc: omap_hsmmc: Update to support of-platdataLokesh Vutla
This is to aid platforms that uses OF_PLATDATA. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-05-09omap_hsmmc: update struct hsmmc to accommodate omap3 from DTAdam Ford
This patch changes the way DM_MMC calculates offset to the base register of MMC. Previously this was through an #ifdef but that wasn't necessary for OMAP3. This patch will now add in the offset to the base address based on the .compatible flags. Signed-off-by: Adam Ford <aford173@gmail.com> V2: Remove ifdef completely and reference offset from the omap_hsmmc_ids table. V1: Change ifdef to ignore OMAP3 Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-30mmc: omap_hsmmc: add support for CONFIG_BLKJean-Jacques Hiblot
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-30mmc: omap_hsmmc: move the mmc_config to platdata when DM_MMC is usedJean-Jacques Hiblot
This is a preparation work for the support of CONFIG_BLK. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-30mmc: omap_hsmmc: use mmc_get_blk_desc() to get the block device descJean-Jacques Hiblot
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-30mmc: omap_hsmmc: use an accessor to get the private dataJean-Jacques Hiblot
For consistency, use an accessor to access the private data. Also for the same reason, rename all priv_data to priv. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-02-09omap_hsmmc.c: Fix build warning on non-omap3Tom Rini
It was incorrect to always include "asm/arch-omap3/mux.h" constantly. This introduced warnings on non-omap3 where certain values will conflict between the various families. Conditionally guard the inclusion in order to correct the problem. Fixes: 6aca17c9b7e8 ("drivers: mmc: omap_hsmmc: Fix IO Buffer on OMAP36xx") Signed-off-by: Tom Rini <trini@konsulko.com>
2017-02-09drivers: mmc: omap_hsmmc: Fix IO Buffer on OMAP36xxAdam Ford
On the OMAP36xx/37xx the CONTROL_WKUP_CTRL register has a field (bit 6) named GPIO_IO_PWRDNZ. If 0, the IO buffers which are related to GPIO_126, 127 and 129 are disabled. Some boards may need this for MMC. After the PBIAS is configured, this bit should be set high to enable these GPIO pins. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-02-08dm: core: Replace of_offset with accessorSimon Glass
At present devices use a simple integer offset to record the device tree node associated with the device. In preparation for supporting a live device tree, which uses a node pointer instead, refactor existing code to access this field through an inline function. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-11mmc: change the set_ios return type from void to intJaehoon Chung
To maintain consistency, set_ios type of legacy mmc_ops changed to int. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-12-04ARM: OMAP4+: Add support for getting pbias info from boardLokesh Vutla
Palmas driver assumes it is always TPS659xx regulator on all DRA7xx based boards to enable mmc regulator. This is not true always like in case of DRA71x-evm. So get this information based on the board. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> [trini: Delete omap4_vmmc_pbias_config from omap_hsmmc.c] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-12-03ARM: DRA7x/AM57xx: Get rid of CONFIG_AM57XXNishanth Menon
CONFIG_AM57XX is just an unnecessary macro that is redundant given So, remove the same instead of spreading through out the u-boot source code and getting in the way to maintain common code for DRA7x family. Acked-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-08-16drivers: mmc: omap_hsmmc: fix build breakageSekhar Nori
structure member 'cd_inverted' of omap_hsmmc_data is available only when OMAP_HSMMC_USE_GPIO is defined. When CONFIG_DM_MMC is defined, but not CONFIG_OMAP_GPIO, this will cause build breakage in omap_hsmmc driver of the sort: CC drivers/mmc/omap_hsmmc.o ../drivers/mmc/omap_hsmmc.c: In function 'omap_hsmmc_ofdata_to_platdata': ../drivers/mmc/omap_hsmmc.c:1763:6: error: 'struct omap_hsmmc_data' has no member named 'cd_inverted' priv->cd_inverted = fdtdec_get_bool(fdt, node, "cd-inverted"); ^ Fix this by accessing cd_inverted only when OMAP_HSMMC_USE_GPIO is defined. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-08-05mmc: use the generic error numberJaehoon Chung
Use the generic error number instead of specific error number. If use the generic error number, it can debug more easier. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-06-09mmc: omap_hsmmc: enable 8bit interface for eMMC for AM33xxHeiko Schocher
Enable 8bit interface on HSMMC2 for am33xx to support 8bit eMMC chips. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-17dm: mmc: Set up the device pointer when using the MMC uclassSimon Glass
Update the existing drivers to set up this new pointer. This will be required by the MMC uclass. Signed-off-by: Simon Glass <sjg@chromium.org>
2016-04-18drivers: mmc: omap_hsmmc: request cd and wp gpios when DM_MMC is definedMugunthan V N
Add request gpio for CD and WP gpios, so that the gpio can be used for the respective purposes. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-18drivers: mmc: omap_hsmmc: Fix conversion of address to a pointerMugunthan V N
omap_hsmmc driver directly typecasts fdt_addr_t to a pointer. This is not strictly correct, as it gives a build warning when fdt_addr_t is u64. So, use map_physmem for a proper typecasts. This is inspired by commit 167efe01bc5a9 ("dm: ns16550: Use an address instead of a pointer for the uart base") drivers/mmc/omap_hsmmc.c: In function ‘omap_hsmmc_ofdata_to_platdata’: drivers/mmc/omap_hsmmc.c:776:20: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] priv->base_addr = (struct hsmmc *)dev_get_addr(dev); ^ Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-15omap_hsmmc: Board-specific TWL6030 MMC power initializationPaul Kocialkowski
Boards using the TWL6030 regulator may not all use the LDOs the same way. Some might also not use MMC1 at all, so VMMC would't have to be enabled. This delegates TWL6030 MMC power initializations to board-specific functions, that may still call twl6030_power_mmc_init for the default behavior. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15power: twl6030: Device-index-specific MMC power initializationPaul Kocialkowski
Not every device has multiple MMC slots available, so it makes sense to enable only the required LDOs for the available slots. Generic code in omap_hsmmc will enable both VMMC and VAUX1, in doubt. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-14dm: block: Rename device number member dev to devnumSimon Glass
This is a device number, and we want to use 'dev' to mean a driver model device. Rename the member. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Stephen Warren <swarren@nvidia.com>
2015-10-22drivers: mmc: omap_hsmmc: convert driver to adopt device driver modelMugunthan V N
adopt omap_hsmmc driver to device driver model Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22ARM: k2g: add SD card and eMMC supportRoger Quadros
Add MMC support for k2g Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-08-12mmc: omap_hsmmc: enable 8bit interface for eMMC for AM43xxNikita Kiryanov
Enable 8bit interface on HSMMC2 for am43xx to support 8bit eMMC chips. Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
generated by cgit (git 2.34.1) at 2025-01-14 14:12:16 +0000