| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Xilinx changes for v2018.07 second pull
zynqmp:
- Show reset reason
- Remove emulation platform
- Update pmufw version
- Simplify mmc bootmode
- Remove dc2 useless configuration file
- Cleanup mini config
- Defconfig syncup
- zcu100, zcu104 and zcu111 dts fixes
xilinx:
- Use live-tree functions in some drivers
- Add support for Avnet Minized and Antminer S9
fpga:
- Add secure bitstream loading support
mmc:
- Add hs200 mode support
usb xhci:
- Header fix
|
|
Add new compatible to the Uniphier SD driver for R8A77990 E3 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
This patch adds HS200 suuport for ZynqMP and enables
the same for ZC1751 DC1 board which has eMMC on it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch updates sdhci_send_command() to handle MMC
HS200 tuning command.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Use live-tree functions.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The compatible string of ftsdc010_mci.c is different from
the mmc driver in Linux Kernel. Modify it for consistency.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
|
|
SDMMC_CMD_CPSMEN bit is wrongly check and set in
SDMMC_ARG register instead of SDMMC_CMD register.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Patch queue for rpi - 2018-05-24
Some minor fixes for the Raspberry Pi:
- Fix SD writes on new sdhost controller
- Sanitize default load addresses, allowing for better payload placement
|
|
Convert CONFIG_SUPPORT_EMMC_RPMB to Kconfig. Split the command handling
from the underlying support and expose this through CMD_MMC_RPMB.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
The bcm2835 sdhost driver has a problem with "write multiple" commands.
It seems to boil down to the fact that the controller dislikes its FIFO
to get drained at the end of a block when a write multiple blocks command
is in flight.
The easy fix is to simply get rid of all the IRQ driven logic and make
the driver push as much data into the FIFO as it can. That way we never
drain and we never run into the problem.
Reported-by: Jan Leonhardt <jan@cyberdesigner.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The check is necessary to avoid NULL pointer dereference.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
|
|
Drop all the extra content from the MMC core, so that tiny MMC support
is really tiny, no fancy anything. That means the tiny MMC support does
only 1-bit transfers at default speed settings. Moreover, this patch
drops duplicate instance of struct mmc mmc_static, which wasted about
360 bytes. Furthermore, since MMC tiny supports only one controller
at all times, get rid of mallocating the ext csd backup and replace
it with static array. All in all, this patch saves ~4 kiB of bloat
from the MMC core, which on platforms with severe limitations can be
beneficial.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup checkpatch.pl style warnings]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This patch adds support of SD3.0 for ZynqMP.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch reads the capabilities register1 and update the host
caps accordingly for mmc layer usage. This patch mainly reads
for UHS capabilities inorder to support SD3.0.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch adds support to invoke any platform specific tuning
and delay routines if available.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch upadted sdhci_send_command to handle execute tuning
command.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch adds support to disable clock if clk_disable
was set and then enable or set clock if the clock was changed
or clock was disabled when clock needs to be enabled.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch changed the datatype of variable "start" from uint to ulong
to work properly on 64-bit machines as well. Also the return type of
get_timer() function is ulong.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
On a socfpga_cyclone5 based board the SD card, was never powered up. For
other dw_mmc based SoCs dwmci_probe() is called in the platform specific
probe(). It seems this call is missing for socfpga_dw_mmc.
With this change DWMCI_PWREN is set by dmwci_init().
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Add the MMC_TRACE config in Kconfig.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Add the debug message for checking the mmc clock status.
It's helpful to debug the controlling clock.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
mmc_set_clock() function has the disable argument as bool type.
When mmc_set_clock is called, it might be passed to "true" or "false".
But it's too confusion whether clock is enabled or disabled with only
"true" and "false".
To prevent the confusion, replace to MMC_CLK_ENABLE/DISABLE macro from
true/false.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The 'SDHCI_QUIRK_NO_HISPD_BIT' is used wrong here. The purpose of this
quirk is to tell the sdhci-driver that the IP-core doesn't have a "high-
speed-enable" bit in its registers.
With this commit we change this to the correct quirk:
SDHCI_QUIRK_BROKEN_HISPD_MODE
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
Some IP-core implementations of the SDHCI have different troubles on the
silicon where they are placed.
On ZYNQ platform for example Xilinx doesn't accept the hold timing of an
eMMC chip which operates in High-Speed mode and must be forced to
operate in non high-speed mode. To get rid of this
"SDHCI_QUIRK_BROKEN_HISPD_MODE" is introduced.
For more details about this refer to the Xilinx answer-recor #59999
https://www.xilinx.com/support/answers/59999.html
This commit:
- doesn't set HISPD bit on the host-conroller
- reflects this fact within the host-controller capabilities
Upon this the layer above (mmc-driver) can setup the card correctly.
Otherwise the MMC card will be switched into high-speed mode and causes
possible timing violation on the host-controller side.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
sd_read_ssr returns 0, means no error.
Fixes: 5b2e72f32721484("mmc: read ssr only if MMC write support is enabled")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
|
|
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Throughput tests have shown the sunxi_mmc driver to take over 10s to
read 10MB from a fast eMMC device due to excessive delays in polling
loops.
This commit restructures the main polling loops to use get_timer(...)
to determine whether a (millisecond) timeout has expired. We choose
not to use the wait_bit function, as we don't need interruptability
with ctrl-c and have at least one case where two bits (one for an
error condition and another one for completion) need to be read and
using wait_bit would have not added to the clarity.
The observed speedup in testing on a A31 is greater than 10x (e.g. a
10MB write decreases from 9.302s to 0.884s).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Mylène Josserand <mylene.josserand@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Staticize the function since it's only used in mmc.c .
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
|
|
|
|
The size of SPL is hitting the limit (64KB) for uniphier_v7_defconfig.
When booting from SD/eMMC, obviously its clock has been properly set up
by the boot ROM. Acutually, no need to re-initialize the clock in SPL.
Using a clock driver would generalize the SoC specific code, but
solving the memory footprint problem would win.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
I need to differentiate the clock handling for uniphier-sd. Move it
to each driver's probe function from the tmio common code so that
renesas-sdhi will not be affected.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The Odroid C2 fails to read from mmc with U-Boot v2018.03.
The change avoids a division by zero.
The fix was suggested by Jaehoon in
https://lists.denx.de/pipermail/u-boot/2018-January/318577.html
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Suggested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
|
|
U-boot driver for sunxi-mmc uses PLL6, unlike linux kernel where
PLL5 is used, with clock rates respectively 600MHz and 768MHz.
Thus there are different phase degree steps - 24 for the kernel and
30 for u-boot.
In the kernel driver the phase is set 90 deg for output and 120 for
sample. Dividing by 30 will result values 3 and 4. Those are the
values set in the u-boot driver.
However, the condition defining delays is wrong. MMC core driver
requests clock of 52MHz, sunxi-driver sets clock of 50MHz, but
phase is set 30 deg for output and 120 deg for sample.
Apparently this works for most cards.
On A20-SOM204-EVB-eMMC there is eMMC card (KLMAG2GEND) which complains
about it. Maybe there is other boards with similar problem?
So the fix is to match delays for both u-boot and kernel.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Add Kconfig entry for SH MMCIF driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Add MMC DM and DT probing support into the SH MMCIF driver.
This patch abstracts out the common bits of the send command
and set ios functions, so they can be used both by DM and non
DM setups and adds the DM probe support.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
|
|
The mv_sdhci driver was not zeroing the sdhci_host structure it
allocates causing random access violations in parts of the mmc core
where the "ops" member pointers are checked and called if not NULL.
Signed-off-by: Matt Pelland <mpelland@starry.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Synchronize the naming with Linux, call the common code TMIO.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The IP requires some time to recuperate after the IO pin
properties were changed. Add a delay to assure this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Fix minor rebase omission, the else was missing which triggered
two accesses to the register on 64bit variant of the IP.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Make sure to wait for the command to complete altogether, including
the trailing 8 clock cycles. This prevents the driver for accidentally
writing the CMD register too fast before the previous command fully
completed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The HOST_MODE register must be set to 0 when the IP is operated in 16bit
mode, otherwise 16bit access to the data FIFO may fail.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
There are only a few registerse used in the 16bit mode which are
32bit internally. Special-case only those in the IO accessors and
always write both halves. Any other register access is protected
from accidentally overwriting neighboring register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add code for PHY tuning required for SDR104/HS200 support on Renesas RCar.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Export the matsu_sd_{read,write}l() common register access
functions, so that they can be used by other drivers sharing
the common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Factor out the regulator handling into set_ios and add support for
selecting pin configuration based on the voltage to support UHS modes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Handle the controller version even if quirks are set. The controller in
Renesas Gen3 SoCs does provide the version register, which indicates a
controller v10 and the controller does support internal DMA and /1024
divider.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Handle bus width 0 as 1-bit bus to assure valid content of
MATSU_SD_OPTION register WIDTH field.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
|
