| Age | Commit message (Collapse) | Author |
|---|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
By default, the subordinate is set equally to the secondary bus (1) when
the RC boots, and does not alter afterwards.
This means that theoretically, the highest bus reachable downstream is
bus 1.
Force the PCIe RC subordinate to 0xff, otherwise no downstream
devices will be detected behind bus 1 if the booting OS does not allow
enumerating a higher busnr than the subordinate value of the primary
bus.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
|
|
Before use GPIO, we need to request gpio first. Free gpio after use.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <ssbabic@denx.de>
|
|
We have at least a minor count of boards, that failed to re-initialize
PCI express in the Linux kernel. Typical failure rate is 20% on affected
boards. This is mitigated by commit 6ecbe1375671 ("drivers: pci: imx:
add imx_pcie_remove function").
However, at least on some i.MX6 custom boards, when calling
assert_core_reset() as part of the first-time PCIe init, read access
to PCIE_PL_PFLR simply hangs. Surround this readl() with
imx_pcie_fix_dabt_handler() does not help. For this reason, the forced
LTSSM detection is only used on the second assert_core_reset() that is
called shorly before starting the Linux kernel.
Signed-off-by: Sven-Ola Tuecke <sven-ola.tuecke@numberfour.eu>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: David Müller <d.mueller@elsoft.ch>
|
|
There is no dedicated reset signal wired up for the MX6QDL thus if the
bootloader enables the link we need some special handling to get the core
back into a state where it is safe to touch it for configuration.
While there has been some special handling in the Linux kernel to do this,
it was removed in 4.11 thus we need to do it properly in the bootloader
and therefore without this if you enable PCI in the bootloader you will hang
while booting the 4.11 kernel.
This puts the PCIe controller back into a safe state for the kernel driver
before launching the kernel.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
|
|
On some boards, the current 20ms timeout
is hit. Increase it to 40mS.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
When trying to access non-existent/unsupported PCI devices in
imx_pcie_read_config(), when imx_pcie_addr_valid() fails it returns
error code and fills in the result with 0xffffffff manually. But it
really should return zero to upper layer codes.
Reported-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
PCI driver currently hangs on mx6qp.
Toggle the reset bit with the appropriate timings to fix the issue.
Based on the FSL kernel driver implementation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
milliseconds should be written as 'ms' instead of 'mS'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Marek Vasut <marex@denx.de>
|
|
If CONFIG_PCI_SCAN_SHOW enabled then lets print a message of no link was
detected.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
Let PCI on mx6solox also be supported.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
According to the IMX6 reference manuals, REF_SSP_EN (Reference clock enable
for SS function) must remain deasserted until the reference clock is running
at the appropriate frequency.
Without this patch we find a high link failure rate (>5%) on certain
IMX6 boards at various temperatures.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Conflicts:
arch/arm/cpu/arm926ejs/mxs/mxsimage.mx23.cfg
arch/arm/cpu/arm926ejs/mxs/mxsimage.mx28.cfg
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
Implement a callback to toggle the slot power supply. The callback
can be overriden in case some more complex power supply for the slot
was implemented in hardware, yet for the usual case, one can define
a GPIO which toggles the power to the slot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Liu Ying <Ying.Liu@freescale.com>
|
|
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Add a callback so that a board can implement it's own specific routine to
toggle the port's #PERST line or #define a GPIO to do so.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
Add PCIe driver for the Freescale i.MX6 SoC . This driver operates the
PCIe block in RC mode only, the EP mode is NOT supported. The driver is
tested with the Intel e1000 NIC driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
|
