| Age | Commit message (Collapse) | Author |
|---|
|
When the requested ECC strength does not exactly match the strengths
supported by the ECC engine, the driver is selecting the closest
strength meeting the 'selected_strength > requested_strength'
constraint. Fix the fact that, in this particular case, ecc->strength
value was not updated to match the 'selected_strength'.
For instance, one can encounter this issue when no ECC requirement is
filled in the device tree while the NAND chip minimum requirement is not
a strength/step_size combo natively supported by the ECC engine.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
|
|
Commit 286ede6 ("drivers: core: Add translation in live tree case") made
dev_get_addr always use proper bus translations for addresses read from
the device tree. But this leads to problems with certain busses, e.g.
I2C busses, which run into an error during translation, and hence stop
working.
It turns out that of_translate_address() and fdt_translate_address()
stop the address translation with an error when they're asked to
translate addresses for busses where #size-cells == 0 (comment from
drivers/core/of_addr.c):
* Note: We consider that crossing any level with #size-cells == 0 to mean
* that translation is impossible (that is we are not dealing with a value
* that can be mapped to a cpu physical address). This is not really specified
* that way, but this is traditionally the way IBM at least do things
To fix this case, we check in both the live-tree and non-live tree-case,
whether the bus of the device whose address is about to be translated
has size-cell size zero. If this is the case, we just read the address
as a plain integer and return it, and only apply bus translations if the
size-cell size if greater than zero.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Reported-by: Martin Fuzzey <mfuzzey@parkeon.com>
Fixes: 286ede6 ("drivers: core: Add translation in live tree case")
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
dm_scan_fdt_node can't work when live dt is active,
we should use dm_scan_fdt_live instead.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Use live dt interface for pinctrl_select_state_full()
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Add api for who can not get phandle from a device property.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
|
|
|
|
|
|
This patch introduced the Aardvark PCIe driver based
driver model.
The PCIe driver is supposed to work in Root Complex
mode. It only supports X1 lane width.
Signed-off-by: Wilson Ding <dingwei@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/38725
Reviewed-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Hua Jing <jinghua@marvell.com>
Tested-by: Hua Jing <jinghua@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch corrects below mpp definitions:
- The sdio_sb group is composed of 6 pins and not 5;
- The rgmii group contains pins mpp2[17:6] and not mpp2[19:6];
- Pin of group "pmic0" is mpp1[6] but not mpp1[16];
- Pin of group "pmic1" is mpp1[7] but not mpp1[17];
- A new group "smi" is added in A0 with 2 pins - mpp2[19:18], its
bitmask is bit4;
- Group "pcie1" has 3 pins in A0 - mpp2[5:3], its bit mask is
bit5 | bit9 | bit10 but not bit4;
- Group "ptp" has 3 pins in A0 as Z1, but its bitmask is changed to
bit11 | bit12 | bit13.
Reviewed-on: http://vgitil04.il.marvell.com:8080/43288
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Hua Jing <jinghua@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
For armada_37xx_update_reg(), the parameter offset should be pointer so
that it can be updated, otherwise offset will keep old value, and then
when offset is larger than or equal to 32 the mask calculated by
"BIT(offset)" will be 0 in gpio chip hook functions, it's an error,
this patch set offset parameter of armada_37xx_update_reg() as pointer.
Reviewed-on: http://vgitil04.il.marvell.com:8080/43287
Reviewed-by: Hua Jing <jinghua@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Pin 23 on South bridge does not belong to the rgmii group. It belongs to
a separate group which can have 3 functions.
Due to this the fix also have to update the way the functions are
managed. Until now each groups used NB_FUNCS(which was 2) functions. For
the mpp23, 3 functions are available but it is the only group which needs
it, so on the loop involving NB_FUNCS an extra test was added to handle
only the functions added.
The bug was visible when the gpio regulator used the gpio 23, the whole
rgmii group was setup to gpio which broke the Ethernet support on the
Armada 3720 DB board. Thanks to this patch, the UHS SD cards (which need
the vqmmc) _and_ the Ethernet work again.
Reviewed-on: http://vgitil04.il.marvell.com:8080/43284
Reviewed-by: Hua Jing <jinghua@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
On the south bridge we have pin from 0 to 29, so it gives 30 pins (and
not 29).
Reviewed-on: http://vgitil04.il.marvell.com:8080/43285
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Hua Jing <jinghua@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Currently, ATU (address translation unit) implementation doesn't
support translate addresses > 32 bits.
This patch allows to configure ATU correctly for different
memory accesses (memory, configuration and IO).
The same approach is used in Linux Kernel.
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Use dm_pci_map_bar function for BAR mapping. This has the advantage
of clearing BAR flags and and only accepting mapped memory.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
It makes no sense to set a PCI region that has 0 size.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
PCI enumeration may happen very early on an x86 board. The board
information pointer should have been checked in decode_regions()
as its space may not be allocated yet.
With this commit, Intel Galileo board boots again.
Fixes: 664758c ("pci: Fix decode regions for memory banks")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
nsd32_mmc was created to support ftsdc010 dm.
It is not necessary to separate both, so merge it
to ftsdc010.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
|
|
Convert CONFIG_FTSDC010_SDIO to Kconfig.
So CONFIG_FTSDC010_SDIO can also be
removed from config_whitelist.txt.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
|
|
Only three defconfig(adp-ag101p_defconfig,
adp-ae3xx_defconfig, nx25-ae250_defconfig)
set CONFIG_FTSDC010=y. And they all also
enable CONFIG_DM_MMC. So the non-dm code
of ftsdc010 can be dropped now.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
|
|
ftsdc010 dm driver has been disable High-Speed mode
as default to work around Andes AE3XX platform's problem,
because of it does not support High-Speed mode in
commit id 73cd56b2df213c629191139e5c6705e069b6214f.
But other platforms or SoCs maybe support this function.
So High-Speed mode can be enabled from dts with
cap-mmc-highspeed or cap-sd-highspeed property.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
|
|
The Rockchip-specific SDHCI wrapper does not process the 'bus-width'
property in the SDHCI node. Consequently, the bus is always kept in
4bit mode, even if 8bit wide operation is available, supported and
requested in the DTS.
This change adds processing of the 'bus-width' property and sets the
host capability flag for an 8bit wide bus, if set to 8. As the logic
in sdhci.c does not support clearing the 4bit capability, we assume
that 4bit operation is always supported.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The patch set dpll settings for 300MHz to values used by binary
blob[1]. With new values dpll still generate 300MHz clock, but
EMAC work. Probably with new values dpll generate more stable clock.
dpll on rk3188 provide clocks to DDR and EMAC. With current
dpll settings EMAC doesn't work on radxa rock. EMAC sends packets
to network, but it doesn't receive anything. ifconfig shows a lot
of framing errors.
[1] https://github.com/linux-rockchip/u-boot-rockchip/blob/u-boot-rk3288/
tools/rk_tools/3188_LPDDR2_300MHz_DDR3_300MHz_20130830.bin
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The error checking should also catch the case that no range has beeen
defined.
syscon_get_first_range() returns NULL if no range is defined.
cf. rk3399_mipi.c
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Pointers are never negative. Use macro IS_ERR() for checking.
cf. rk3288_mipi.c
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Assigning f_rkusb->reboot_flag twice doesn't make sense.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
If we want to check the duration we need to increment the counter.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Clean the iomux definitions at grf_rk3188.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Clean the iomux definitions at grf_rk3036.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
This adds support for the (to date unsupported) I2C controllers 1~4
and 6~7 (i.e. now all controllers except I2C5, which is not accessible
on the RK3399-Q7, are supported by pinctrl).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
|
|
|
|
|
|
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
|
|
The ti,pindir-d0-out-d1-in property is not expected to have a value
according to the device-tree binding, so treat it as a boolean not a
uint property.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
This patch print pl clocks (pl0...pl3) and watchdog
clock using clk dump.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
NAND erase was not happening for size 1GiB or more. Erase
command was executing successfully but in actual, it was not
erasing.
This patch fixed erase issue for 1 GiB or more size nand.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This IP can be found on Zynq and ZynqMP devices.
The driver was tested with reset-on-timeout; feature.
Also adding WATCHDOG symbol to Kconfig because it is required.
Signed-off-by: Shreenidhi Shedi <imshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
watchdog clock is also connected to cpu 1X clocksource.
Zynq> clk dump
...
Before:
swdt 4294967290
After:
swdt 111111110
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch bypasses phy detection logic for GMII interface
and just depend on phy address received from DT. This patch
is required as phy detection logic is different for some phys
like xilinx phy which can be connected over SGMII and GMII
interface.
This fixes the issue of ethernet failures when xilinx phy is
connected over GMII interface.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Check !desc earlier to simplify code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
|
|
In
lpi2c_status_t result = A;
result = B;
the first assignment has no effect. Let's remove it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
|
|
With DM enabled in SPL, DM_FLAG_PRE_RELOC is required for
the omap_gpio driver to be bound to the gpio devices.
Therefore, add DM_FLAG_PRE_RELOC flag to the omap_gpio driver.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Last user of this driver went away in October 2014 in
commit d58a9451e7339ed4 ("ppc/arm: zap EMK boards").
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
In
if (a > =0) {...}
else (a < 0) {...}
the second logical constraint is superfluous.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
In
int ret = A;
ret = B;
the first assignment has not effect.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
