summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2020-09-11mtd: nand: Fix nand write error with bad block addresses above 32-bitT Karthik Reddy
Nand writes should skip the bad blocks with "nand write" command. In case of bad blocks with above 32-bit address, nand_block_isbad() returns false due to truncated bad block address. In below code segment, if (nand_block_isbad(mtd, offset & ~(mtd->erasesize - 1))) offset is 64-bit and mtd->erasesize is 32-bit, hence the truncation is happening. Cast 'mtd->erasesize' with loff_t to fix this issue. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-09-10PCI: mediatek: Release the resource when PCIe enable port failChuanjia Liu
On the mt7623 platform, if one port enable fail and other port enable succeed. It will hang on when using pci enum because the resource was not released correctly. Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com> Tested-by: Frank Wunderlich <frank-w@public-files.de>
2020-09-08bcmgenet: Add support for rgmii-rxidJason Wessel
The commit 57805f2270c4 ("net: bcmgenet: Don't set ID_MODE_DIS when not using RGMII") needed to be extended for the case of using the rgmii-rxid. The latest version of the Rasbperry Pi4 dtb files for the 5.4 now specify the rgmii-rxid. Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Tested-by: Petr Tesarik <ptesarik@suse.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-09-08bcmgenet: fix DMA buffer managementJason Wessel
This commit fixes a serious issue occurring when several network commands are run on a raspberry pi 4 board: for instance a "dhcp" command and then one or several "tftp" commands. In this case, packet recv callbacks were called several times on the same packets, and send function was failing most of the time. note: if the boot procedure is made of a single network command, the issue is not visible. The issue is related to management of the packet ring buffers (producer / consumer) and DMA. Each time a packet is received, the ethernet device stores it in the buffer and increments an index called RDMA_PROD_INDEX. Each time the driver outputs a received packet, it increments another index called RDMA_CONS_INDEX. Between each pair of network commands, as part of the driver 'start' function, previous code tried to reset both RDMA_CONS_INDEX and RDMA_PROD_INDEX to 0. But RDMA_PROD_INDEX cannot be written from driver side, thus its value was actually not updated, and only RDMA_CONS_INDEX was reset to 0. This was resulting in a major synchronization issue between the driver and the device. Most visible behavior was that the driver seemed to receive again the packets from the previous commands (e.g. DHCP response packets "received" again when performing the first TFTP command). This fix consists in setting RDMA_CONS_INDEX to the same value as RDMA_PROD_INDEX, when resetting the driver. The same kind of fix was needed on the TX side, and a few variables had to be reset accordingly (c_index, tx_index, rx_index). The rx_index and tx_index have only 256 entries so the bottom 8 bits must be masked off. Originated-by: Etienne Dublé <etienne.duble@imag.fr> Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Tested-by: Petr Tesarik <ptesarik@suse.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-09-04phy: marvell: a3700: add sata comphy on lane 2 with invert optionzachary
- This patch moves sata phy powerup from dedicate phy to compphy and adds invert option for sata powerup routine. Change-Id: I1b4e8753e2b2c14c6efa97bca2ffc7d2553d8a90 Signed-off-by: zachary <zhangzg@marvell.com> Signed-off-by: Ken Ma <make@marvell.com> Reviewed-on: http://vgitil04.il.marvell.com:8080/53601 Reviewed-by: Igal Liberman <igall@marvell.com> Tested-by: Igal Liberman <igall@marvell.com> [a.heider: adapt to mainline] Signed-off-by: Andre Heider <a.heider@gmail.com> Tested-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2020-09-03Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
- Mostly DFU fixes and r8152 fixes
2020-09-03Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- SH serial bugfix
2020-09-01fastboot: getvar: fix partition-size return valueGary Bisson
The size returned by 'getvar partition-size' should be in bytes, not in blocks as fastboot uses that value to generate empty partition when running format [1]. Note that the function was already returning the proper size in bytes for NAND devices (see struct part_info details). [1] https://android.googlesource.com/platform/system/core/+/refs/heads/android10-release/fastboot/fastboot.cpp#1500 Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
2020-09-01fastboot: Fix fastboot reboot fail by changing functions orderyurii.pidhornyi
It was revealed that when the fastboot_tx_write_str function is called without the previously initialized fastboot_func->in_req->complete field, a copy of in_req will be sent to the I/O requests queue without an initialized field. Moving a piece of code with the initializing of the fastboot_func->in_req->complete field above transmit_tx allows to solve this problem. Fixes: 65c96757fe9 "usb: fastboot: Convert USB f_fastboot to shared fastboot" Signed-off-by: yurii.pidhornyi <yurii.pidhornyi@globallogic.com>
2020-09-01f_sdp: Change bInterval of interrupt endpoint to 3Sherry Sun
Since the USB HID limits the maximum bandwidth(3072) for interrupt endpoint transfers, when the bInterval set to 1, we can only support 3 boards to run sdp at the same time. In order to support more boards, change the bInterval of interrupt endpoint to 3, which will not affect the transmission speed. Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-01f_sdp: Add EP1_OUT as default data receive pipe in sdpSherry Sun
EP0 has been used to transfer file data in sdp before, but the max packetsize of ep0 is 64 bytes. So in order to improve the file transfer speed, here add the EP1_OUT interrupt endpoint which max packetsize is set to 1024 byte. After testing, it turns out that using ep1out is twice as fast as using ep0 while receiving data in sdp. Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-01f_sdp: Support searching and loading FIT or container imagePeng Fan
Add support to f_sdp to search and load iMX8 container image or iMX8M FIT image by new UUU command SDPV. When using the SDPV, the uuu will continue to send out data after first level boot loader used by ROM. This means uuu won't skip to the offset of the second boot loader, and the padding data before second boot loader will be sent out. So we have to search the FIT header or container header in the buffer that SDP received. Also change to more common method to exit f_sdp handler not depending on SPL_FIT_FOUND flag because container loader won't set this. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-01f_sdp: Fix wrong usb request sizeYe Li
Because the buffer length of sdp usb request is 65, we have to allocate 65 bytes not 64 bytes. Otherwise there is potential buffer overflow. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-09-01f_sdp: Add high speed endpoint descriptorYe Li
Add HS endpoint descriptor for SDP. So that we can use high speed endpoint, and the SDP device can send packet with 512 byte size. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-09-01usb: max3420: add the gadget driverJassi Brar
MAX3420 implements FullSpeed USB Device over SPI. Another version MAX3421, also implements USB Host mode. This driver should be good for the device mode of max3421 as well. Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
2020-09-01fastboot: Add default fastboot_set_reboot_flag implementationRoman Kovalivskyi
Default implementation of fastboot_set_reboot_flag function that depends on "bcb" commands could be used in general case if there are no need to make any platform-specific implementation, otherwise it could be disabled via Kconfig option FASTBOOT_USE_BCB_SET_REBOOT_FLAG. Please note that FASTBOOT_USE_BCB_SET_REBOOT_FLAG is mutually exclusive with some platforms which already have their own implementation of this function. Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
2020-09-01fastboot: Add support for 'reboot fastboot' commandRoman Kovalivskyi
Android 10 adds support for dynamic partitions and in order to support this userspace fastboot must be used[1]. New tool fastbootd is included into recovery. Userspace fastboot works from recovery and is launched if: 1) - Dynamic partitioning is enabled 2) - Boot control block has 'boot-fastboot' value into command field The bootloader is expected to load and boot into the recovery image upon seeing boot-fastboot in the BCB command. Recovery then parses the BCB message and switches to fastbootd mode[2]. Please note that boot script is expected to handle 'boot-fastboot' command in BCB and load into recovery mode. Bootloader must support 'reboot fastboot' command which should reboot device into userspace fastboot to accomodate those changes[3]. Another command that bootloader must support[3] is 'reboot recovery'. This command should simply reboot device into recovery mode. [1] - https://source.android.com/devices/bootloader/fastbootd [2] - https://source.android.com/devices/bootloader/fastbootd#unified_fastboot_and_recovery [3] - https://source.android.com/devices/bootloader/fastbootd#modifications_to_the_bootloader Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com> Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com> Change-Id: I9d2bdc9a6f6f31ea98572fe155e1cc8341e9af76
2020-09-01fastboot: Extend fastboot_set_reboot_flag with reboot reasonRoman Kovalivskyi
Extend fastboot_set_reboot_flag arguments with reboot reason so that it could handle different reboot cases in future. Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
2020-09-01dfu: fix dfu tftp on sandboxHeinrich Schuchardt
The environment variable loadaddr is in the virtual address space of the sandbox. To get the actual memory address where the FIT image has been loaded we have to convert this address according to the memory mapping of the sandbox. Equally the addresses in the *.its file have to be converted when used in the dfu_ram driver. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-09-01dfu: DFU_MTD depends on CMD_MTDPARTSHeinrich Schuchardt
Function mtdparts_init() is needed for the DFU MTD driver. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-09-01fastboot: Support defining raw partitions without a partition tableFilip Brozovic
Add support for defining raw fastboot partitions in eMMC by specifying the offset and size in an environment variable. Optionally, the eMMC hardware partition number may also be specified. This makes it possible to e.g. update only part of the eMMC boot partition, instead of having to write the entire partition. Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
2020-09-01usb: ci_udc: Add function to remove usb deviceYe Li
When unregister gadget driver in ci_udc, the usb device is not removed or stop. This causes next "usb start" fails to work. Add a new interface "usb_remove_ehci_gadget" in usb-uclass to remove the usb device for DM driver. Using "usb_lowlevel_stop" for non-DM driver. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-01usb: gadget: Fix controller index in UMSYe Li
The usb mass storage (f_mass_storage.c) uses fixed usb index 0, this causes problem while CDNS3 USB controller index is 1. Modify the API of fsg to pass the controller index. Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-01eth/r8152: support RTL8153B/RTL8154BHayes Wang
This is used to support RTL8153B and RTL8154B. Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2020-09-01eth/r8152: modify rtl_clear_bp functionHayes Wang
The original rtl_clear_bp() is used to clear the firmware of both PLA and USB MCU. The new one could clear the firmware of PLA or USB independently. It is unnecessary to clear firmware, if there is no one to be updated. Besides, clear the firmware by writing the relative registers in bulk. Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2020-09-01eth/r8152: reset PHY after setting itHayes Wang
Some settings of PHY have to work after resetting PHY. Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2020-09-01eth/r8152: reset bmu after disabling Tx/RxHayes Wang
Reset bmu after disabling Tx/Rx. This is used to clear the FIFO of Tx/Rx. The remained data may be transferred after Tx/Rx is re-enabled. And it results in garbage data. Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2020-09-01serial: sh: Improve FIFO empty check on RXMarek Vasut
If the SCIF is receiving data quickly enough, it may happen that the SCxSR_RDxF flag is cleared in sh_serial_getc_generic(), while the FIFO still contains data. If that happens, the serial_getc_check() reports no data in the FIFO as the flag is no longer set. Add one more check, if the SCxSR_RDxF is not set, read out the FIFO level and if there are still characters in the FIFO, permit reading them out. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2020-09-01x86: pinctrl: Fix 'relatove' typoSimon Glass
Fix this typo in the Kconfig help. Suggested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-08-31Merge tag 'ti-v2020.10-rc4' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-ti - Update to ABI 3.0 - Fix i2c write in eeprom driver
2020-08-31arm64: a37xx: pci: Depends on DM_GPIOPali Rohár
For proper initialization of aardvark pci driver it is required to de-assert reset GPIO. So depeneds on DM_GPIO option. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31mmc: xenon: set signal voltage and max base clockEvan Wang
- The SDIO signal voltage and max base clock frequency setting are missing in driver, which causes SDIO not working. - The patch adds SDIO signal voltage switch support, which is based on regulator-gpio of vqmmc-supply, and sets the max base clock frequency. - Fix the zero clock value in call to sdhci_setup_cfg() function. Change-Id: I79c8860c65b8db166f4f70db56ede4097f71f1fa Signed-off-by: Evan Wang <xswang@marvell.com> Reviewed-on: http://vgitil04.il.marvell.com:8080/53589 Reviewed-by: Hua Jing <jinghua@marvell.com> Tested-by: Hua Jing <jinghua@marvell.com> [pali: Amended fixup patch] Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31arm64: a37xx: pci: Assert PERST# signal when unloading driverPali Rohár
This change ensures that PCIe card is put into reset state when U-Boot stops using it. DM_FLAG_OS_PREPARE ensures that U-Boot executes driver's remove callback prior booting Linux kernel. Linux kernel pci-aardvark driver needs to reset PCIe card via PERST# signal prior initializing it. If it does not issue reset then some PCIe cards (specially Compex WiFi cards) are not detected at all. Putting PCIe card into reset state prior booting Linux kernel would ensure that card would be properly reset at time when Linux kernel starts initializing pci-aardvark driver. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Konstantin Porotchkin <kostap@marvell.com> Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31arm64: a37xx: pci: Make PCIe Reset GPIO DT compatible with Linux kernel DTPali Rohár
Change active-high to active-low and change DT property name from reset-gpio to reset-gpios. This format of gpio reset is used by pci-aardvark driver in Linux kernel. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Konstantin Porotchkin <kostap@marvell.com> Tested-by: Andre Heider <a.heider@gmail.com>
2020-08-31firmware: ti_sci: Drop unused structure ti_sci_rm_type_mapLokesh Vutla
struct ti_sci_rm_type_map is no longer used. Drop its definition and its declarations. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-08-31firmware: ti_sci: drop the device ids to resource id translation tableLokesh Vutla
With ABI 3.0, sysfw deprecated special resource types used for AM65x SoC. Instead started using device id as resource type similar to the convention used in J721E SOC. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-08-27pci: kconfig: Setup proper dependency for PCIE_ROCKCHIPMichal Simek
There is missing dependency for PCIE_ROCKCHIP which selects PHY_ROCKCHIP_PCIE which directly depends on ARCH_ROCKCHIP. WARNING: unmet direct dependencies detected for PHY_ROCKCHIP_PCIE Depends on [n]: ARCH_ROCKCHIP [=n] Selected by [y]: - PCIE_ROCKCHIP [=y] && PCI [=y] Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2020-08-27drivers: usb: Fix config indentationRuben Di Battista
The indentation was messing up with the scripts/build-whitelist.sh that was marking SYS_USB_EVENT_POLL_VIA_INT_QUEUE (and probably also the other indented options) erroneously as ad-hoc configure option with the following error: ``` Error: You must add new CONFIG options using Kconfig The following new ad-hoc CONFIG options were detected: CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE ```
2020-08-25Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvellTom Rini
- Add basic Marvell/Cavium OcteonTX/TX2 support (Suneel) - Infrastructure changes to PCI uclass to support these SoC's (Suneel) - Add PCI, MMC & watchdog driver drivers for OcteonTX/TX2 (Suneel) - Increase CONFIG_SYS_MALLOC_F_LEN for qemu-x86 (Stefan)
2020-08-25Merge tag 'i2c-bugfixes-for-v2020.10' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-i2c i2c bugfixes for v2020.10 - fix some issues with octeon_i2c driver on ARM Octeon TX2 - fix link failure with CONFIG_SPL and CONFIG_I2C_MUX_PCA954x
2020-08-25Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscvTom Rini
- Sipeed Maix support S-mode. - Provide command sbi. - Use fdtdec_get_addr_size_auto_parent to get fu540 cache base address. - Fix a compiler error with CONFIG_SPL_SMP=n. - Fix sifive ram driver 32 compiler warnings. - Fix kendryte/pll.h redefine nop() warning.
2020-08-25watchdog: Add reset support for OcteonTX / TX2Suneel Garapati
Adds support for Core 0 watchdog poke on OcteonTX and OcteonTX2 platforms. Signed-off-by: Suneel Garapati <sgarapati@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-08-25mmc: Add MMC controller driver for OcteonTX / TX2Suneel Garapati
Adds support for MMC controllers found on OcteonTX or OcteonTX2 SoC platforms. Signed-off-by: Aaron Williams <awilliams@marvell.com> Signed-off-by: Suneel Garapati <sgarapati@marvell.com> Cc: Peng Fan <peng.fan@nxp.com>
2020-08-25pci: Add PCI controller driver for OcteonTX / TX2Suneel Garapati
Adds support for PCI ECAM/PEM controllers found on OcteonTX or OcteonTX2 SoC platforms. Signed-off-by: Suneel Garapati <sgarapati@marvell.com> Reviewed-by: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com>
2020-08-25ata: ahci: Add BAR index quirk for Cavium PCI SATA deviceSuneel Garapati
For SATA controller found on OcteonTX SoC's, use non-standard PCI BAR0 instead of BAR5. Signed-off-by: Suneel Garapati <sgarapati@marvell.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-08-25pci: pci-uclass: Check validity of ofnodeSuneel Garapati
Add check if the referenced ofnode is valid. Signed-off-by: Suneel Garapati <sgarapati@marvell.com> Reviewed-by: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com>
2020-08-25pci: pci-uclass: Add support for Alternate-RoutingID capabilitySuneel Garapati
If ARI capability is found on device, use it to update next function number in bus scan and also helps to skip unnecessary bdf scans. Signed-off-by: Suneel Garapati <sgarapati@marvell.com> Reviewed-by: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com>
2020-08-25pci: pci-uclass: Add VF BAR map support for Enhanced AllocationSuneel Garapati
Makes dm_pci_map_bar API available to map BAR for Virtual function PCI devices which support Enhanced Allocation. Signed-off-by: Suneel Garapati <sgarapati@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com>
2020-08-25pci: pci-uclass: Add support for Single-Root I/O VirtualizationSuneel Garapati
SR-IOV - Single Root I/O Virtualization PF - Physical Function VF - Virtual Function If SR-IOV capability is present, use it to initialize Virtual Function PCI device instances. pci_sriov_init function will read SR-IOV registers to create VF devices under the PF PCI device and also bind driver if available. This function needs to be invoked from Physical function device driver which expects VF device support, creating minimal impact on existing framework. Signed-off-by: Suneel Garapati <sgarapati@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com>
2020-08-25pci: pci-uclass: Add support for Enhanced Allocation in BridgesSuneel Garapati
If Enhanced Allocation capability is present in bridges, use it to read the fixed sub-ordinate bus number. Signed-off-by: Suneel Garapati <sgarapati@marvell.com> Reviewed-by: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com>
generated by cgit (git 2.34.1) at 2024-12-26 20:11:55 +0000