summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2019-02-09dm: device: fail uclass_find_first_device() if list_emptyMarcel Ziswiler
While uclass_find_device() fails with -ENODEV in case of list_empty strangely uclass_find_first_device() returns 0. Fix uclass_find_first_device() to also fail with -ENODEV instead. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-02-09watchdog: bcm6345: allow to use this driver on arm bcm63158Philippe Reynes
This IP is also used on some arm SoC, so we allow to use it on arm bcm63158 too. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-02-09mmc: omap_hsmmc: Workaround errata regarding SDR104/HS200 tuning failures (i929)Faiz Abbas
Errata i929 in certain OMAP5/DRA7XX/AM57XX silicon revisions (SPRZ426D - November 2014 - Revised February 2018 [1]) mentions unexpected tuning pattern errors. A small failure band may be present in the tuning range which may be missed by the current algorithm. Furthermore, the failure bands vary with temperature leading to different optimum tuning values for different temperatures. As suggested in the related Application Report (SPRACA9B - October 2017 - Revised July 2018 [2]), tuning should be done in two stages. In stage 1, assign the optimum ratio in the maximum pass window for the current temperature. In stage 2, if the chosen value is close to the small failure band, move away from it in the appropriate direction. References: [1] http://www.ti.com/lit/pdf/sprz426 [2] http://www.ti.com/lit/pdf/SPRACA9 Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-02-09clk: stm32mp1: correctly handle Clock Spreading GeneratorPatrick Delaunay
To activate the csg option, the driver need to set the bit2 of PLLNCR register = SSCG_CTRL: Spread Spectrum Clock Generator of PLLn enable. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-09clk: stm32mp1: add debug informationPatrick Delaunay
Add support of clk dump command and display information during probe (under CONFIG_DISPLAY_CPUINFO). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-09clk: stm32mp1: recalculate counter when switching freqPatrick Delaunay
Because stgen is initialized with HSI clock, we need to recalculate the counter when changing frequency. Signed-off-by: Lionel Debieve <lionel.debieve@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-09clk: stm32mp1: correct access to RCC_OCENSETR/RCC_OCENCLRRPatrick Delaunay
Remove unnecessary setbits on set/clear registers. Avoid to deactivate HSI with HSE. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-09clk: stm32mp1: add IPCC clockPatrick Delaunay
Add support for enable/disable of IPCC clock using AHB3 registers Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-09clk: stm32mp1: no more get ck_usbo_48m in device treePatrick Delaunay
Remove support of ck_usbo_48m clock node in device tree, but force 48MHz frequency to prepare alignment with kernel device tree. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-09drivers: serial: dm: Enable DM_FLAG_PRE_RELOC in SBSA pl011 uart driverVabhav Sharma
The DM_FLAG_PRE_RELOC shall be enabled in SBSA PL011 uart driver as this driver is used in NXP based SoCs It is necessary to have Serial console running before relocation The !CONFIG_IS_ENABLED(OF_CONTROL) [*] check is set as "workaround" for DM problem : 4687919684e This flag is set if board does not support device-tree and using platform data, In DM Model either of device tree or platform data can be used to fetch device configuration It is possible to use SBSA UART with CONFIG_DM_SERIAL but witout corresponding device tree description (OF_CONTROL) Other board/SoCs have this flag set unconditionally Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
2019-02-09watchdog: bcm6345: allow to use this driver on arm bcm6858Philippe Reynes
This IP is also used on some arm SoC, so we allow to use it on arm bcm6858 too. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-02-09watchdog: bcm6345: switch to raw I/O functionsPhilippe Reynes
This driver is used on several big endian mips board. So we could use raw I/O function instead of forcing big endian access. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-02-09mmc: Do not poll using CMD13 when changing timingMarek Vasut
When using CMD6 to switch eMMC card timing from HS200/HS400 to HS/legacy, do not poll for the completion status using CMD13, but rather wait 50mS. Once the card receives the CMD6 and starts executing it, the bus is in undefined state until both the card finishes executing the command and until the controller switches the bus to matching timing configuration. During this time, it is not possible to transport any commands or data across the bus, which includes the CMD13. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Jaehoon Chung <jh80.chung@samsung.com>
2019-02-09mmc: tmio: renesas: Add 1uS delay after DMA completion on older IPsMarek Vasut
The internal DMAC asserts DMA transfer end bit too early on older version of the TMIO IPs which use bit 17 for DTRAEND. Add 1uS delay after the completion of DMA transfer and before invalidating the cache to let the DMAC fully complete the transfer. Otherwise, it could happen that the last few bytes of a transferred data are not available. A test case to trigger this behavior is the following command, ran on the U-Boot command line, with Sandisk 16 GiB UHS-I card inserted into SDHI slot 0 and with first partition being of type FAT: => while true ; do mmc rescan ; fstype mmc 0:1 ; done Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-02-09mmc: tmio: Make DMA transfer end bit configurableMarek Vasut
Different versions of the SDHI core use either bit 17 or bit 20 for the DTRAEND indication, which can differ even between SoC revisions. Make the DTRAEND bit position part of the driver private data, so that the probe function can set this accordingly. Set this to 20 on Socionext SoCs and either 17 or 20 on Renesas SoCs, depending on the SoC. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-02-08dm: core: Introduce dev_read_alias_highest_id()Michal Simek
It is wrapper for calling of_alias_get_highest_id() when live tree is enabled and fdtdec_get_alias_highest_id() if not. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-02-08dm: core: Add of_alias_get_highest_id()Michal Simek
The same functionality was added to Linux for i2c bus registration with this commit message: " of: base: add function to get highest id of an alias stem I2C supports adding adapters using either a dynamic or fixed id. The latter is provided by aliases in the DT case. To prevent id collisions of those two types, install this function which gives us the highest fixed id, so we can then let the dynamically created ones come after this highest number. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> " Add it also to U-Boot for DM I2C support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-02-07Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
- SPI-NOR support
2019-02-07configs: Don't use SPI_FLASH_BAR as defaultVignesh R
Now that new SPI NOR layer uses stateless 4 byte opcodes by default, don't enable SPI_FLASH_BAR. For SPI controllers that cannot support 4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c, renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to not break functionality. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: Add lightweight SPI flash stack for SPLVignesh R
Add a tiny SPI flash stack that just supports reading data/images from SPI flash. This is useful for boards that have SPL size constraints and would need to use SPI flash framework just to read images/data from flash. There is approximately 1.5 to 2KB savings with this. Based on prior work of reducing spi flash id table by Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: Remove unused filesVignesh R
spi_flash and spi_flash_ids are no longer needed after SPI NOR migration. Remove them. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: Switch to new SPI NOR frameworkVignesh R
Switch spi_flash_* interfaces to call into new SPI NOR framework via MTD layer. Fix up sf_dataflash to work in legacy way. And update sandbox to use new interfaces/definitions Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: sf_probe: Add "jedec, spi-nor" compatible stringVignesh R
Linux uses "jedec,spi-nor" as compatible string for JEDEC compatible SPI Flash device nodes. Therefore make U-Boot also to look for the same compatible string so that we can use Linux DTS files as is. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: spi-nor-core: Add back U-Boot specific featuresVignesh R
For legacy reasons, we will have to keep around U-Boot specific SPI_FLASH_BAR and SPI_TX_BYTE. Add them back to the new framework Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: spi-nor-core: Add SFDP supportVignesh R
Sync Serial Flash Discoverable Parameters (SFDP) parsing support from Linux. This allows auto detection and configuration of Flash parameters. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: spi-nor-core: Add 4 Byte addressing supportVignesh R
Sync changes from Linux SPI NOR framework to add 4 byte addressing support. This is required in order to support flashes like MT35x that no longer support legacy Bank Address Register(BAR) way of accessing >16MB region. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: spi-nor-core: Add SPI MEM supportVignesh R
Many SPI controllers have special MMIO interfaces which provide accelerated read/write access but require knowledge of flash parameters to make use of it. Recent spi-mem layer provides a way to support such controllers. Therefore, add spi-mem support to spi-nor-core as a way to support SPI controllers with MMIO interface. SPI MEM layer takes care of translating spi_mem_ops to spi_xfer()s in case of legacy SPI controllers. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: Port SPI NOR framework from LinuxVignesh R
Current U-Boot SPI NOR support (sf layer) is quite outdated as it does not support 4 byte addressing opcodes, SFDP table parsing and different types of quad mode enable sequences. Many newer flashes no longer support BANK registers used by sf layer to a access >16MB of flash address space. So, sync SPI NOR framework from Linux v4.19 that supports all the above features. Start with basic sync up that brings in basic framework subsequent commits will bring in more features. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07spi: Add non DM version of SPI_MEMVignesh R
Add non DM version of SPI_MEM to support easy migration to new SPI NOR framework. This can be removed once DM_SPI conversion is complete. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07spi: spi-mem: Claim SPI bus before spi mem accessVignesh R
It is necessary to call spi_claim_bus() before starting any SPI transactions and this restriction would also apply when calling spi-mem operations. Therefore claim and release bus before requesting transfer via exec_op. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07spi: spi-mem: Extend spi_mem_adjust_op_size() to honor max xfer sizeVignesh R
Extend spi_mem_adjust_op_size() to take spi->max_write_size and spi->max_read_size into account. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07spi: spi-mem: Allow use of spi_mem_exec_op for all SPI modesVignesh R
SPI controllers support all types of SPI modes including dual/quad bus widths. Therefore remove constraint wrt SPI mode from spi-mem layer. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-05Merge git://git.denx.de/u-boot-marvellTom Rini
- Move Armada XP / 38x PCIe driver to DM_PCI from me - Move Armada XP / 38x LCD driver to DM_VIDEO from me - Add uDPU board (Armada-3720) from Vladimir [trini: Fix warning in pci-uclass.c by removing ret from pci_uclass_child_post_bind as it no longer calls functions with a return code to catch.] Signed-off-by: Tom Rini <trini@konsulko.com>II
2019-02-05video: Armada XP: Move driver to DM_VIDEOStefan Roese
This patch moves the Armada XP video / LCD driver to DM_VIDEO. With this move, the legacy interface board_video_init() is removed from the theadorable board code (only user of this video driver). The support via DT will be added in a separate patch. This patch also enables DM_VIDEO for the theadorable board, as this is needed to not break git bisect'ability. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Anatolij Gustschin <agust@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2019-02-05pci: pci_mvebu: Add DM_PCI support and move CONFIG_PCI_MVEBU to defconfigStefan Roese
This patch adds DM_PCI support to the MVEBU PCIe driver. This is necessary, since all PCI drivers have to be moved to DM (driver model) until the v2019.07 release. To not break git bisect'ablility, this patch also moves CONFIG_PCI_MVEBU from config headers to the defconfig files. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Mario Six <mario.six@gdsys.cc> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Phil Sutter <phil@nwl.cc> Cc: Marek Behún <marek.behun@nic.cz> Cc: VlaoMao <vlaomao@gmail.com>
2019-02-05pci: Add pci_get_devfn() to extract devfn from the fdt_pci_addrStefan Roese
This function will be used by the Marvell Armada XP/38x PCIe driver, which is moved to DM right now. So let's extract the functionality from pci_uclass_child_post_bind() to make it available. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-02-02Merge tag 'for-master-20190201' of git://git.denx.de/u-boot-rockchipTom Rini
u-boot-rockchip changes for 2019.04-rc1: * support for Chromebook Bob * full pinctrl driver using DTS properties * documentation improvements * I2S support for some Rockchip SoCs
2019-02-02Merge tag 'mips-pull-2019-02-01' of git://git.denx.de/u-boot-mipsTom Rini
- MIPS: mscc: jr2: small fixes - MIPS: mscc: luton: add ethernet and switch driver - MIPS: mt76xx: fix timer frequency
2019-02-01regulator: pbias: Handle extended drain IO when changing omap36 PBIASAdam Ford
The OMAP36 and DM37 TRM state to disable extneded drain IO before changing the PBIAS. This patch does this before pmic writes if the CONFIG_MMC_OMAP36XX_PINS flag is set and the cpu family is omap36xx Signed-off-by: Adam Ford <aford173@gmail.com>
2019-02-01pinctrl: Kconfig: fix missing include of rockchip/KconfigPhilipp Tomsich
After the merge of the new, generic pinctrl-code, the include for rockchip/Kconfig was missing. Add it here, so we can select the pinctrl-driver for SPL. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01pinctrl: Kconfig: sort includes alphabeticallyPhilipp Tomsich
To make adding new subdirectories easier, let's enforce alphabetical ordering of the includes of Kconfig files in the respective subdirectories. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01rockchip: Implement spl_gpio in the GPIO driverSimon Glass
Allow rockchip boards to use GPIOs before driver model is ready. This is really only useful for setting GPIOs to enable the early debug console, if needed on some platforms. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01rockchip: clk: Add mention of four new clocksSimon Glass
These clocks are needed to get MMC running. We don't actually support setting them yet. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01clk: Improve debug message in clk_set_default_rates()Simon Glass
It is helpful to print the clock number as well as the index, so that this can be looked up in the binding file. Update the debug() statement to do this. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01pinctrl: rockchip: Clean the unused rockchip pinctrl driversDavid Wu
If we used the pinctrl-rockchip driver, these code is not needed, so remove them. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01pinctrl: rockchip: Add common rockchip pinctrl driverDavid Wu
Use this driver to fit all Rockchip SOCs and to support the desired pinctrl configuration via DTS. Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01rockchip: Add a sound driverSimon Glass
Add a sound driver for rk3288 supporting chromebook_jerry. This uses the I2S driver, and existing audio codec and the clock/pinmux support. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01rockchip: Add an I2S driverSimon Glass
Add a driver for I2S which allows audio data to be sent from the SoC to the audio codec. The sample rate and other settings are hard-coded for now as there is no suitable device-tree binding available. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01rockchip: rk3288: Add i2s pinctrl and clock supportSimon Glass
Add support for setting pinctrl and clock for I2S on rk3288. This allows the sound driver to operate. These settings were created by rkmux.py Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01usb: ether: call _usb_eth_halt() if initialization failsJean-Jacques Hiblot
If the host does not respond in time, the initialization fails. However the usb ether driver will still be registered. This will make usb_gadget_probe_driver() fail the next time the initialization is attempted because it cannot find an available UDC. Fixing this by calling _usb_eth_halt() when the init fails. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Acked-by: Lukasz Majewski <lukma@denx.de>
generated by cgit (git 2.34.1) at 2024-12-28 18:18:46 +0000