summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2016-01-27ppc: xilinx-ppc4xx: Port to DM serialRicardo Ribalda Delgado
xilinx_uartlite has been ported to DM, this patch makes the xilinx-ppc405-generic and the xilinx-ppc440-generic boards use the new DM driver. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27mmc: zynq_sdhci: Added qurik to disable high speedSiva Durga Prasad Paladugu
Add quirk to disable high speed incase the high speed was broken.This solves the issue where the the controller is used in High Speed Mode and the the hold time requirement for the JEDEC/MMC 4.41 specification is NOT met. This timing issue is not on all boards and hence provided config option to enable it when required. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Emil Lenchak <emill@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27mmc: sdhci: Clear high speed if not supportedSiva Durga Prasad Paladugu
Clear high speed bit if it was not supported by the driver. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Emil Lenchak <emill@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27sdhci: zynq: Remove hardcoded value zero as min frequencySiva Durga Prasad Paladugu
Remove hardcoded value zero as min frequency and use config option CONFIG_ZYNQ_SDHCI_MIN_FREQ defined in board config Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: zynq: Change MDC setup for arm64Michal Simek
MDC setting depends on pclk input clocks which varies across SoC. This driver is used by xilinx zynq and zynqmp SOC. Input clock frequence on silicon is 125MHz where divider 64 put frequency below 2.5MHz requires by spec (125/64=1.95). Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: phy: ti: Enable automatic crossover modeMichal Simek
Enable automatic crossover cable detection. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27serial: zynq: Fix address reading from DMMichal Simek
Use dev_get_addr() instead of reading reg base directly in the driver. Core function is also more robust. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27serial: zynq: Extend compatible string listMichal Simek
ZynqMP is using updated core with cdns,uart-r1p12 compatible string. Signed-off-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27fpga: xilinx: Check for substring in device ID validationSiva Durga Prasad Paladugu
Check for substrings in deviceID validation check so that it can support xa bitstreams also. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: emaclite: Move emaclite to KconfigMichal Simek
Add PHYLIB and MII dependencies and enable it by default for Microblaze. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Let core to handle received packetMichal Simek
Pass pointer to core to handle packet. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: emaclite: Rename start and stop functionsMichal Simek
Rename start and stop functions to align with DM functions names. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: emaclite: Move driver to DMMichal Simek
Move driver to DM. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Use indirect access in emaclite_recvMichal Simek
When IP is configured with pong buffers, IP is receiving packets to ping and then to pong buffer and than ping again. The original logic in the driver remains there that when ping buffer is free, pong buffer is checked too and return if both are free. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: emaclite: Use indirect reg access in sendMichal Simek
The original logic in the driver was exchanging buffers which are used for sending packet and tx_ping and tx_pong buffers were exchanged all the time to ensure that IP has enough time to send the packet out. Based on this "feature" send function was using nextbuffertouse variable to save which buffer should be used. Before this algorithm was called driver checked that there is free buffer available. This checking remains in the driver but driver tries to use tx_ping first if available. If not, tx_pong buffer is used instead. To reach this code the original condition is met that at least one of the buffer should be available. Testing doesn't show any performance drop when this patch is applied. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Remove XEL_TSR_XMIT_ACTIVE_MASK flagMichal Simek
This flag is not documented anywhere in the latest documentation that's why this patch removes it. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Fix logic around available TX buffersMichal Simek
Simplify logic how to find out if there is free TX buffer. Both buffers are checked all the time that's why logic around order can be removed. Also add check when only one buffer is available. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Use indirect register access for TX resetMichal Simek
Move to use indirect register access when timeout expires for resetting TX buffers. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Use indirect register access for rx_ping/pongMichal Simek
Do initialization via indirect register access. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: emaclite: Use indirect register access for tx_ping/pongMichal Simek
Do initialization via indirect register access. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Convert MDIO to use register offsetMichal Simek
Use u-boot coding style how to setup and access MDIO bus. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Add MDIO support to driverMichal Simek
Add MDIO support before move to DM. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: emaclite: Remove ancient OF probe functionMichal Simek
Prepare for DM move. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: Add axi emac to KconfigMichal Simek
Also add dependency on PHYLIB and MII which is required. Clean PHYLIB dependency from the driver too. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Rename start, stop, write_hwaddr functionsMichal Simek
Rename few functions to fit to the new name convention used by DM. Suggested-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: axi_emac: Split recv from free_pktMichal Simek
Call net_process_received_packet() by core. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Enable access to MDIO in probeMichal Simek
Detect phy when driver probes. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Move driver to DMMichal Simek
Move driver to DM. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Pass private structure where possibleMichal Simek
Use axidma_priv instead of ethdevice in preparation of the DM move. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27net: axi_emac: Pass private structure to phyread/phywriteMichal Simek
Prepare for move to DM. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Put iobase to private structureMichal Simek
Saving iobase directly to private structure helps with moving to DM. There is an option to load iobase from pdata but it is additional load. Pointer to private structure is available all the time. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Pass directly pointer to register spaceMichal Simek
Simplify mdio_wait function by passing regs directly. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Show phy address instead of register contentMichal Simek
Fix debug message. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: axi_emac: Fix parentheses around operand !Michal Simek
Fix these compilation warning by proper grouping: In function 'axi_dma_init': drivers/net/xilinx_axi_emac.c:391:7: warning: suggest parentheses around operand of '!' or change '&' to '&&' or '!' to '~' [-Wparentheses] if (!(in_be32(&priv->dmatx->control) | ^ In function 'axiemac_send': drivers/net/xilinx_axi_emac.c:501:21: warning: suggest parentheses around operand of '!' or change '&' to '&&' or '!' to '~' [-Wparentheses] while (timeout && (!in_be32(&priv->dmatx->status) & Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27serial: uartlite: Add uartlite to KconfigMichal Simek
- Move config option out of board file. - Remove uartlite address from config file Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
2016-01-27serial: uartlite: Add support for debug consoleMichal Simek
Add support for debug console. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
2016-01-27serial: uartlite: Move driver to DMMichal Simek
Enable SPL DM too. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
2016-01-27mailaddr: Update mail addressRicardo Ribalda Delgado
The old mail address will stop working soon. Update it all the files Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27atmel_nand: use the definition: PMECC_OOB_RESERVED_BYTES instead magic numberJosh Wu
As atmel_nand_ecc.h is sync with v4.1 kernel, which adds the PMECC_OOB_RESERVED_BYTES. So use it in the driver. Signed-off-by: Josh Wu <josh.wu@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2016-01-27atmel_nand: add '\n' in the end of error message for better displayJosh Wu
Also align the open parenthesis. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-01-27atmel_nand: use nand ecc_{strength, step}_ds instead of our own functionJosh Wu
Since ecc_{strength,step}_ds is introduced in nand_chip structure for minimum ecc requirements. So we can use them directly and remove our own get_onfi_ecc_param function. Signed-off-by: Josh Wu <josh.wu@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2016-01-27net: macb: Not all the GEM are gigabit capableGregory CLEMENT
During the initialization of PHY the gigabit bit capable is set if the controller is a GEM. However, for sama5d2 and sama5d4, the GEM is configured to support only 10/100. Improperly setting the GBE capability leads to an unresponsive MAC controller. This patch fixes this behavior allowing using the gmac with these SoCs. Suggested-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> [fixed minor checkpatch warning] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-01-27mmc: atmel: Properly fix clock configurationGregory CLEMENT
Timing issue occurs on eMMC not only when modifying the frequency but also for all the switch command(CMD6). According to the MMC spec waiting 8 clocks after a switch command would be the thing to do. This patch allows fixing CPU hang observed when trying to changing the bus width on a eMMC on SAMA5D4. Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by: Marek Vasut <marex@denx.de> # on DENX MA5D4EV Acked-by: Marek Vasut <marex@denx.de> Tested-by: Andreas Bießmann <andreas.devel@googlemail.com> # on atngw100 Acked-by: Andreas Bießmann <andreas.devel@googlemail.com> [fixed minor checkpatch warning] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-01-26Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini
2016-01-26mvtwsi: Fix breakage introduced by "Fix mvtwsi not working on sun6i and ↵Hans de Goede
newer sunxi SoCs" "Fix mvtwsi not working on sun6i and newer sunxi SoCs" includes the following: @@ -189,7 +200,8 @@ static int twsi_start(struct i2c_adapter *adap, int expected_status) /* globally set TWSIEN in case it was not */ twsi_control_flags |= MVTWSI_CONTROL_TWSIEN; /* assert START */ - writel(twsi_control_flags | MVTWSI_CONTROL_START, &twsi->control); + twsi_control_flags |= MVTWSI_CONTROL_START | MVTWSI_CONTROL_CLEAR_IFLG; + writel(twsi_control_flags, &twsi->control); /* wait for controller to process START */ return twsi_wait(adap, expected_status); } The modification of twsi_control_flags done here was introduced while merging to fix a line > 80 chars, but twsi_control_flags is a global variable and should not be modified like this here, this commit fixes this, restoring mvtwsi functionality. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26sunxi: power: axp818: Enable support for ALDOsChen-Yu Tsai
Previously, AXP818 ALDO support was partially added to Kconfig, but never enabled in the board file, nor properly set or configured in Kconfig. The boards continue to work because the AXP818 is designed to pair with the A83T/H8, and the default voltages match the reference design's requirements. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26power: axp818: Add support for DLDO and ELDO regulatorsChen-Yu Tsai
AXP818 provides an array of LDOs to provide power to various peripherals. None of these regulators are critical. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26power: axp: merge separate DLDO functions into 1Chen-Yu Tsai
Instead of one function for each DLDO regulator, make 1 function that takes an extra "index". Since the control bits for the DLDO regulators are contiguous, this makes the function very simple. This removes a lot of duplicate code. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26sunxi: Implement poweroff support for axp221 pmicHans de Goede
Adds poweroff support for axp221 pmic. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-01-26sunxi: Implement poweroff support for axp209 pmicMichael van Slingerland
Adds poweroff support for axp209 pmic. Signed-off-by: Michael van Slingerland <michael@deviousops.nl> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
generated by cgit (git 2.34.1) at 2025-01-22 18:18:42 +0000