summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2008-02-14Fix remaining CONFIG_COMMANDSJean-Christophe PLAGNIOL-VILLARD
update comments Fix coding style Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-02-14Remove duplicate defines for ARRAY_SIZEKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-02-14Fix incorrect address test in AT91F_DataflashSelect().Stelian Pop
Signed-off-by: Stelian Pop <stelian@popies.net>
2008-02-12Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
2008-02-12QE: Move FDT support into a common fileKumar Gala
Move the flat device tree setup for QE related devices into a common file shared between 83xx & 85xx platforms that have QE's. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-02-05OMAP5912: fix FIFO handling in UART driverWolfgang Denk
According to the OMAP5912 Serial Interfaces Reference Guide (see http://focus.ti.com/lit/ug/spru760c/spru760c.pdf, page 150), the FIFO_EN enable bit in the FIFO Control Register (FCR) can only be changed when the baud clock is not running, i. e. when both DLL and DLH are set to 0. Thus make sure that DLL and DLH are 0 when writing the FCR. Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-29Fix conditional compilation of mpx8xxx_spi driverBen Warren
This driver should only compile if CONFIG_MPC8XXX_SPI is set Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-23Merge ../custodiansWolfgang Denk
2008-01-23Merge branch 'master' of git://www.denx.de/git/u-boot-shWolfgang Denk
2008-01-23Coding Style Cleanup; update CHANGELOGWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-23Merge branch 'master' of git://www.denx.de/git/u-boot-coldfireWolfgang Denk
2008-01-23Merge branch 'master' of git://www.denx.de/git/u-boot-netWolfgang Denk
2008-01-23Merge branch 'master' of git://www.denx.de/git/u-boot-mpc85xxWolfgang Denk
2008-01-17Merge branch 'kumar'Andy Fleming
2008-01-17ColdFire: Add MCF547x_8x FEC driverTsiChungLiew
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Signed-off by: John Rigby <jrigby@freescale.com>
2008-01-17ColdFire: Add MCF547x_8x dma code and header filesTsiChungLiew
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com> Signed-off by: John Rigby <jrigby@freescale.com>
2008-01-17ColdFire: Add MCF547x_8x dma code - 2TsiChungLiew
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com> Signed-off by: John Rigby <jrigby@freescale.com>
2008-01-17ColdFire: Add MCF547x_8x dma code - 1TsiChungLiew
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com> Signed-off by: John Rigby <jrigby@freescale.com>
2008-01-17codingstyle cleanup for spi driverKim Phillips
..and rm unused CONFIG_FSL_SPI define Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-17Add support for a Freescale non-CPM SPI controllerBen Warren
This patch adds support for the SPI controller found on Freescale PowerPC processors such as the MCP834x family. Additionally, a new config option, CONFIG_HARD_SPI, is added for general purpose SPI controller use. Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-17sh: Update SuperH SCIF driverNobuhiro Iwamatsu
This patch fixed wrong SH7720 CPU macro and changed macro that calculated value of SCBRR register. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-01-1685xx: Move LAW init code into CKumar Gala
Move the initialization of the LAWs into C code and provide an API to allow modification of LAWs after init. Board code is responsible to provide a law_table and num_law_entries. We should be able to use the same code on 86xx as well. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-16drivers/net/rtl8139.c: rx_status should be le32_to_cpu(rx_status).Shinya Kuribayashi
rx_status on the memory is basically in LE, but needs to be handled in CPU endian. le32_to_cpu() takes up this mission. Even if on the sane hardware, it'll work fine. Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com> Cc: Masami Komiya <mkomiya@sonare.it> Cc: Lucas Jin <lucasjin@gmail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-16drivers/net/rtl8139.c: Fix cache coherency issuesShinya Kuribayashi
Current driver is meant for cache coherent systems. This patch adds flush_cache() routines to support cache non-coherent systems. Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com> Cc: Masami Komiya <mkomiya@sonare.it> Cc: Lucas Jin <lucasjin@gmail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-16drivers/net/rtl8139.c: Fix tx timeoutShinya Kuribayashi
"to = (currticks() + RTL_TIMEOUT)" has possibilities to wrap around. If it does, the condition "(currticks() < to)" becomes invalid and immediately leads to tx timeout error. This patch introduces the fine-graded udely(10) loops to ease the impact of wrapping around. Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com> Cc: Masami Komiya <mkomiya@sonare.it> Cc: Lucas Jin <lucasjin@gmail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-16TSEC: Add the support for RealTek RTL8211B PHYDave Liu
Add the support of RealTek RTL8211B PHY, the RTL8211B PHY only supports RGMII and MII mode. Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-16Remove annoying debug printout for PHY less boards.Joakim Tjernlund
PHY less board prints out lots of "read wrong ...": read wrong value : mii_id 3,mii_reg 2, base e0102320 read wrong value : mii_id 3,mii_reg 3, base e0102320 UEC: PHY is Generic MII (ffffffff) read wrong value : mii_id 3,mii_reg 4, base e0102320 read wrong value : mii_id 3,mii_reg 0, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 5, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 5, base e0102320 FSL UEC0: Full Duplex FSL UEC0: Speed 100BT FSL UEC0: Link is up Using FSL UEC0 device Make this printout depend on UEC_VERBOSE_DEBUG and remove its definition in uec_phy.c Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-16net: reduce boot latency on QE UEC based boardsKim Phillips
actually polling for PHY autonegotiation to finish enables us to remove the 5 second boot prompt latency present on QE based boards. call to qe_set_mii_clk_src in init_phy, and mv call to init_phy from uec_initialize to uec_init by Joakim Tjernlund; autonegotiation wait code shamelessly stolen from tsec driver. also rm unused CONFIG_RMII_MODE code. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-16TSEC driver: Change MDIO support to allow access to any PHYs on the MDIO busmichael.firth@bt.com
The current TSEC driver limits MDIO access to the devices that have been configured as attached to a TSEC MAC. This patch allows access to any PHY device on the MDIO bus through the 'mii' commands. Signed-off-by: Michael Firth <michael.firth@bt.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-16Merge branch 'master' of git://www.denx.de/git/u-boot-shWolfgang Denk
2008-01-16nand: FSL UPM NAND driverAnton Vorontsov
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-01-16OneNAND: Separate U-Boot dependent code from OneNANDKyungmin Park
OneNAND: Separate U-Boot dependent code from OneNAND Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2008-01-15QE UEC: Extend number of supported UECs to 4David Saada
This patch extends the number of supported UECs to 4. Note that the problem of QE thread resources exhaustion is resolved by setting the correct number of QE threads according to Ethernet type (GBE or FE). Signed-off-by: David Saada <david.saada@ecitele.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-15pcmcia: Remove CONFIG_COMMANDS from marubun pcmcia driverNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-01-15sh: Add support SH7710/SH7712Nobuhiro Iwamatsu
SH7710/SH7712 of SH3 CPU are supported. SH771X is called SH-Ether, and has the Ether controller in CPU. The driver of Ether is not included in this patch. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-01-15sh: Add support for SH7720 in serial_sh driver.Yoshihiro Shimoda
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-01-14QE: fix compile warningDave Liu
qe.c: In function 'qe_upload_firmware': qe.c:390: warning: pointer targets in passing argument 2 uec.c: In function 'uec_initialize': uec.c:1236: warning: 'uec_info' may be used uninitialized Signed-off-by: Dave Liu <daveliu@freescale.com>
2008-01-13CFI: Fix CONFIG_FLASH_CFI_LEGACY compilationMichael Schwingen
Signed-off-by: Michael Schwingen <michael@schwingen.org> Acked-by: Stefan Roese <sr@denx.de>
2008-01-12USB: Add Philips 1561 PCI-OHCI idsTsiChung Liew
(needed for M5475EVB) Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
2008-01-12Remove superfluous preprocessor conditionals from LM73 driverLarry Johnson
(1) Remove unused symbol "CFG_EEPROM_PAGE_WRITE_ENABLE". (2) Use conditional Makefile.o. Signed-off-by: Larry Johnson <lrj@acm.org>
2008-01-11Add Fujitsu CoralP/Lime video driverAnatolij Gustschin
Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Rodolfo Giometti <giometti@linux.it>
2008-01-11Fix video console newline and carriage return handlingAnatolij Gustschin
Lines of the lenght CONSOLE_COLS or greater than CONSOLE_COLS are not displayed correctly. This is an attempt to fix this issue. Also add carriage return handling. Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Rodolfo Giometti <giometti@linux.it>
2008-01-10Fix Ethernet init() return codesBen Warren
Change return values of init() functions in all Ethernet drivers to conform to the following: >=0: Success <0: Failure All drivers going forward should return 0 on success. Current drivers that return 1 on success were left as-is to minimize changes. Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-By: Timur Tabi <timur@freescale.com>
2008-01-10Coding Style cleanup; update CHANGELOGWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-0985xx: add ability to upload QE firmwareTimur Tabi
Define the layout of a binary blob that contains a QE firmware and instructions on how to upload it. Add function qe_upload_firmware() to parse the blob and perform the actual upload. Add command-line command "qe fw" to take a firmware blob in memory and upload it. Update ft_cpu_setup() on 85xx to create the 'firmware' device tree node if U-Boot has uploaded a firmware. Fully define 'struct rsp' in immap_qe.h to include the actual RISC Special Registers. Signed-off-by: Timur Tabi <timur@freescale.com>
2008-01-09fix various commentsMarcel Ziswiler
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2008-01-09fix comments with new drivers organizationMarcel Ziswiler
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2008-01-09Fix endianness conversions in rtl8169 driverGuennadi Liakhovetski
It is unclear on what platforms this driver has been tested, since noone up to now defines CONFIG_RTL8169 in the board configuration header. Now it has been fixed for a big-endian mpc8241 based linkstation platform. This patch presents the necessary endianness conversion fixes. Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-01-09Add Epson RX8025 RTC supportMatthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-01-08Add support CONFIG_UEC_ETH3 in MPC83xxJoakim Tjernlund
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
generated by cgit (git 2.34.1) at 2024-12-26 07:27:54 +0000