summaryrefslogtreecommitdiff
path: root/include/configs/kp_imx53.h
AgeCommit message (Collapse)Author
2020-08-08Convert CONFIG_SYS_MMC_ENV_DEV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_ENV_PART Note that with this conversion we now have consistent behavior with respect to ensuring that we have always selected the correct MMC device and hardware partition. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28Convert CONFIG_ENV_OVERWRITE to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-20env: Finish migration of common ENV optionsTom Rini
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20env: Remove useless CONFIG_ENV_SIZE_REDUND and fix ENV_IS_REDUND checkTom Rini
We have CONFIG_ENV_SIZE_IS_REDUND but don't really use it. We have one board where we can simply multiple CONFIG_ENV_SIZE by two for the same result. The other place where we could but were not previously using this is for where env_internal.h checks for if we should set ENV_IS_EMBEDDED. This seems like the most likely use, historically, of the variable, but it was not used. Add logic to check for this now. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-11-12defconfigs: Migrate CONFIG_SYS_REDUNDAND_ENVIRONMENTTom Rini
Move this symbol to Kconfig. As part of this we can drop a UBI-specific symbol that was a stop-gap for not having this particular symbol in Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-06-11config: Update KP's imx53 HSC config to pass key pressed informationLukasz Majewski
The information about pressed key is relevant in performing correct update and recovery scenarios via USB pendrive. This commit modifies envs to provide it. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-06-11config: Update KP's imx53 HSC config to support SWUpdateLukasz Majewski
This commit updates envs responsible for using USB pendrive as a SWUpdate based tool for recovery and update. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25Convert CONFIG_USB_EHCI_MX5 to KconfigLukasz Majewski
This converts the following to Kconfig: CONFIG_USB_EHCI_MX5 Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: config: Remove not needed CONFIG_MXC_USB_PORT defineLukasz Majewski
After i.MX5's EHCI conversion to DM, the CONFIG_MXC_USB_PORT is not needed anymore and should be removed. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: kp_imx53: config: Do not use ${boardtype} to setup update wic fileLukasz Majewski
After unification of the rootfs for both HSC and DDC devices, only one, common wic file is necessary - without the distinction of specific board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: Remove non DM/DTS esdhc3 code from HSC|DDC board related filesLukasz Majewski
After switching to DM/DTS support of esdhc3 - the code in this patch can be removed. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-25ARM: defconfig: Move CONFIG_FSL_ESDHC to KconfigLukasz Majewski
The CONFIG_FSL_ESDHC is now enabled and defined in Kconfig, not in include/configs/kp_imx53.h Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-04-02cosmetic: Remove not needed string from kp_imx53.h configLukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-08-17Convert CONFIG_MII et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-18board: Silent out the console on the K+P's imx53 boardsLukasz Majewski
Disable console output by default on imx53 based boards from K+P. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-05-18Fixup various SPDX tags from the latest mergeTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-18arm: imx53: Add support for imx53 boards from K+PLukasz Majewski
This commit adds support for DDC and HSC boards from K+P in u-boot. Console output: U-Boot 2018.05-rc2-00090-g752b7ed6f9 (Apr 26 2018 - 14:24:24 +0200) CPU: Freescale i.MX53 rev2.1 at 800 MHz Reset cause: WDOG Model: K+P iMX53 DRAM: 512 MiB MMC: FSL_SDHC: 0 Loading Environment from MMC... OK In: serial Out: serial Err: serial Module EEPROM: ID: TQMa53-CB.0401 SN: 63152762 MAC: 00:0b:64:03:14:2a BBoard:40x0 Rev:10 Net: eth0: ethernet@63fec000 Hit any key to stop autoboot: 0 Signed-off-by: Lukasz Majewski <lukma@denx.de>