| Age | Commit message (Collapse) | Author |
|---|
|
This converts the following to Kconfig:
CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
This converts the following to Kconfig:
CONFIG_SPL_NAND_BASE
CONFIG_SPL_NAND_IDENT
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
This converts the following to Kconfig:
CONFIG_SPL_NAND_DRIVERS
CONFIG_SPL_NAND_ECC
CONFIG_SPL_NAND_SIMPLE
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The env variable overlay_files is used while adding the environment
support commands for FIT loading, but it was cleaned up just prior in
commit ee53b59511a6 ("configs: Remove unneeded overlay_files environment
variable"). Fix this by replacing the undefined variable with the
proper name_overlays env variable.
Fixes: 76470b6929d5 ("configs: ti: Add environment support commands for FIT loading")
Signed-off-by: Suman Anna <s-anna@ti.com>
|
|
Read correct dtb blob from boot.img/recovery.img and apply correct dtbo
blobs from dtbo partition.
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Both 'loadfit' and 'mmcloados' start with a call to 'args_mmc' so this
can be factored out to before eithers only call site. This also allows us
to remove that call from 'loadfit', which should not have been calling it
anyway as that command should not be MMC specific. Without the call to
'args_mmc' the command 'loadfit' becomes just a call to 'run_fit' so
remove the indirection and call 'run_fit' directly, this removes the need
for 'loadfit' command (which was misnamed anyway). Drop it.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
When running 'run_fit' the FIT file should have been loaded at
'addr_fit', although at this point they should be the same
use this variable instead of 'loadaddr'.
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
Some parts of these commands can be reused, add them to common files.
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
Like we did with 'fit_loadaddr' to 'addr_fit', the variable
'fit_bootfile' contains a name and so should be prefixed with
name_. Make this change here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
This is the first part of a larger effort I would like to propose to
unify and simplify the default set of environment variables.
When many early environment variables were named there were fewer images
being loaded, usually just a kernel. At this time names like 'loadaddr'
would suffice. Now we have more images and many more commands that act on
them, often re-using the same variable for several different uses. The
contents of a variable are also not immediately known causing one to have
to look up a chain of variables to understand what a command is actually
doing. I suggest the following.
To start, all variables containing names should be prefixed with name_
and addresses with addr_. This is like how K2 already does things and
allows for simple universal commands like:
get_fdt_nfs=nfs ${addr_fdt} /boot/${name_fdt}
Which is very clear on what is intended here and would work across all
board that using the this naming convention.
We can do this one variable at a time, start here with addr_fit.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
|
|
The FIT image is loaded to 0x8700_0000 followed by extracting from that
several large images also into the 0x8x00_0000 range. Large images
can end up overwriting the FIT image as it is being extracted from.
Move the FIT load address clear out to 0x9000_0000, this will require
a board to have at least 256MB of DRAM, if less then more careful
planning will be required for that platform.
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C
API when DM_I2C is used. The goal is to eventually remove DM_I2C_COMPAT
when all I2C "clients" have been migrated to use the DM API.
This a step in that direction for the TI based platforms.
Build tested with buildman:
buildman -dle am33xx ti omap3 omap4 omap5 davinci keystone
boot tested with:
am335x_evm, am335x_boneblack, am335x_boneblack_vboot (DM version),
am57xx_evm, dra7xx_evm, k2g_evm, am437x_evm
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Add initial support for AM654 based EVM running on R5.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
|
|
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_MTD_PARTITIONS
CONFIG_MTD_DEVICE
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SPI
This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
With the contents of config_distro_defaults.h migrated to Kconfig,
we can remove this header file completely
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig. We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important. In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Now that the fallback value of CONFIG_SYS_PBSIZE in
include/config_fallbacks.h has been adjusted, remove its definition
from a large number of board configuration files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_CMD_SPL
Note that trats does not actually use SPL, so this option can no-longer be
set.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The load address of ramdisk, rdaddr is 0x88080000 and fit_loadaddr
is defined as 0x88000000. This leaves only 512Kbytes for the
fit image. When the FIT images are larger than this, it will
overwite the ramdisk and cause the boot to fail.
For eg, The K2 HS fit images are a few MB and end up overwriting
the ramdsk. This patch moves the fit_loadaddr to 0x87000000,
leaving a 16MB window for the fit image. This memory can be
reclaimed once the kernel starts running.
Signed-off-by: Madan Srinivas <madans@ti.com>
|
|
The above CONFIG options are in Kconfig, and now have correct depends and
inter-dependencies. Migrate these to configs/ from include/configs/. In the
case of CMD_UBIFS also change it to be a default y if CMD_UBI.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
(>750KB). We need to increase it. eMMC uses a much bigger area (2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region
"spl-os-image.raw".
both: region "spl-os-image.raw" is quite small and can't handle android
kernels
Fixing this requires growing some regions and moving others.
Care has been taken to leave some room for further growth of
"spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the
region is not free space that can be used to grow "u-boot.img.raw".
The MLO region is 0x100 sectors wide but the 0x100 are unused in case the
MLO comes too overflow this areas.
The total space allocated for those raw binaries is 16MB, of which 13+MB
are reserved for the kernel image.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
Enable support for writing to FAT partitions on
TI's boards.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
This converts the following to Kconfig:
CONFIG_SPL_BOARD_INIT
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The most common name for a FIT image containing a bootable kernel is
"fitImage", as our builds now use this name also, change this to the
default in our U-Boot environment.
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
Introduce include/environment/ti/mmc.h that
consolidates environment variable definitions
for various TI boards that support MMC/SD.
This allows reuse of same environment variables
on non-ARMv7 TI platforms like OMAP-L138 for
example.
While at it, move DFU-related environment variable
includes to only non-SPL builds for AM335x and
AM437x since they are not really used for SPL
today.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The env command 'args_fit' does not define a root path, this forces us to
embed the rootfs into the FIT image. FIT images do not need to contain a
rootfs, when they do not the kernel will fall-back to the kernel argument
'root', if this is not defined the kernel will not boot. It is safe to
add this as when we do have the rootfs in FIT this argument is ignored.
As 'loadfit' is only called from the MMC boot path, use 'args_mmc' to
correctly populate 'bootargs'.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Move this in to Kconfig with a default of 115200.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons. We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode. So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
|
|
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.
During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.
This commit was created as follows:
[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.
[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"
[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'
[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'
[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.
Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig. Almost all
of the defines will go away.
I see only two exceptions:
configs/blanche_defconfig
configs/sandbox_noblk_defconfig
They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something
might be wrong with these two boards, so should be checked later.
Anyway, this is the output of the moveconfig tool.
This commit was created as follows:
[1] create a config entry in drivers/mmc/Kconfig
[2] tools/moveconfig.py -r HEAD GENERIC_MMC
[3] manual clean-up of garbage comments in doc/README.* and
include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly
update all of the config files we must also update CMD_PART and CMD_GPT to also
be in Kconfig in order to avoid complex logic elsewhere to update all of the
config files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
|
This allows us to specify a FIT configuration that will automatically
use the correct images from the FIT blob.
Signed-off-by: Andrew F. Davis <afd@ti.com>
|
|
Commit 7a777f6d6f35 ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f66 ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.
We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.
I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.
This commit was created as follows:
[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)
[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
There are certain environment variables whose length is greater than
the defined IO buffer size. So, increase the IO buffer size to print the
entire variables.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
FIT is a new image format which is a Tree like structure and gives more
flexibility in handling of various images. Mainly used for unification of
multiple images in a single blob and provide security information for each
image.
U-Boot already has support for loading such images, so adding the environment
support to load FIT image on all TI platforms.
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Support for loading images from mmc is duplicated in all TI platforms.
Add this information to DEFAULT_MMC_TI_ARGS so that it can be reused
in all TI platforms.
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This option isn't used for anything, so get rid of it.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Fix sniper and kc1 migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_INFO_QUIET
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default n, re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move SPL_OS_BOOT to Kconfig and cleanup existing
uses.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Authentication of images in Falcon Mode is not supported. Do not enable
SPL_OS_BOOT when TI_SECURE_DEVICE is enabled. This prevents attempting
to directly load kernel images which will fail, for security reasons,
on HS devices, the board is locked if a non-authenticatable image load
is attempted, so we disable attempting Falcon Mode.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Previously we had been adjusting CONFIG_SYS_MALLOC_LEN based on if
CONFIG_DFU_MMC has been set or not. However, for quite some time this
has not been the case as we often include <configs/ti_armv7_common.h>
prior to setting CONFIG_DFU_MMC so we would always use 16MiB and then
not have enough room for to DFU files. Given the amount of memory we
always have, setting a minimum size of 32MiB for malloc is reasonable.
However, in the SPL case not only do we not need that much we start
running into overlap problems and then will fail to boot. Since we
don't need 16MiB in the SPL case, bring this down to 8MiB.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
