summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2015-03-01ARM: UniPhier: switch to xHCI for PH1-Pro4Masahiro Yamada
PH1-Pro4 includes both EHCI and xHCI IP cores. Unfortunately, U-Boot cannot enable EHCI and xHCI support simultaneously. Some users may wish Super-Speed connection. Disable CONFIG_USB_EHCI_HCD and enable CONFIG_USB_XHCI_HCD. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2015-02-28Exynos542x: Config: Add various configsAkshay Saraswat
This patch adds "iRAM, CPU state and low power" configs which are the addresses acting as flag registers. iROM code checks CONFIG_LOWPOWER_FLAG address. If it is equal to CONFIG_LOWPOWER_EN then it jumps to the address (0x02020000+CPUID*4). This is a part of iROM logic. Rest other flags are being used at various places during kernel switching and reset. They are nowhere documented because they are part programming. These configs are serving as flags for us because they are representing the addresses in iRAM which we are using for storing and extracting CPU Status and GIC status. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2015-02-25Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2015-02-25arm: rmobile: silk: Add support SDHIVladimir Barinov
This adds GPIO configuration and initialization function of SDHI on Silk board Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-25arm: rmobile: Add Porter board supportVladimir Barinov
Porter is an entry level development board based on R-Car M2 SoC (R8A7791) This commit supports the following peripherals: - SCIF, I2C, Ethernet, QSPI, SD, USB Host Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-25arm: rmobile: lager: Add support SDHINobuhiro Iwamatsu
Lager board has two SDHI port as SDHI0 and SDHI2. This adds GPIO configuration and initialization function of SDHI, and enables MMC command. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-25arm: rmobile: gose: Add support SDHINobuhiro Iwamatsu
Gose board has three SDHI port. This adds GPIO configuration and initialization function of SDHI, and enables MMC command. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-25arm: rmobile: koelsch: Add support SDHINobuhiro Iwamatsu
Koelsch board has three SDHI port. This adds GPIO configuration and initialization function of SDHI, and enables MMC command. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-25arm: rmobile: alt: Add support SDHINobuhiro Iwamatsu
Alt board has two SDHI port. This adds GPIO configuration and initialization function of SDHI, and enables MMC command. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-25arm: rmobile: silk: Migrate serial driver to drivers modelNobuhiro Iwamatsu
This adds drivers model support of serial port to Silk board, and migrate serial port to drivers model. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-25arm: rmobile: alt: Migrate serial driver to drivers modelNobuhiro Iwamatsu
This adds drivers model support of serial port to Alt board, and migrate serial port to drivers model. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-25arm: rmobile: lager: Migrate serial driver to drivers modelNobuhiro Iwamatsu
This adds drivers model support of serial port to Lager board, and migrate serial port to drivers model. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-25arm: rmobile: gose: Migrate serial driver to drivers modelNobuhiro Iwamatsu
This adds drivers model support of serial port to Gose board, and migrate serial port to drivers model. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-25arm: rmobile: koelsch: Migrate serial driver to drivers modelNobuhiro Iwamatsu
This adds drivers model support of serial port to Koelsch board, and migrate serial port to drivers model. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2015-02-24zmx25: Convert to generic boardFabio Estevam
Boards need to select CONFIG_SYS_GENERIC_BOARD in order to prevent removal from the project. Cc: Matthias Weisser <weisserm@arcor.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-02-24imx31_phycore: Convert to generic boardFabio Estevam
Boards need to select CONFIG_SYS_GENERIC_BOARD in order to prevent removal from the project. Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-02-24mx31ads: Convert to generic boardFabio Estevam
Boards need to select CONFIG_SYS_GENERIC_BOARD in order to prevent removal from the project. Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-02-24ARM: davinci: remove hawkboard supportMasahiro Yamada
This is still a non-generic board. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Sughosh Ganu <urwithsughosh@gmail.com> Cc: Syed Mohammed Khasim <sm.khasim@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
2015-02-24ARM: remove tnetv107x board supportMasahiro Yamada
This is still a non-generic board. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Chan-Taek Park <c-park@ti.com> Acked-by: Marek Vasut <marex@denx.de>
2015-02-24ARM: remove a320evb board supportMasahiro Yamada
This is still a non-generic board. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Po-Yu Chuang <ratbert@faraday-tech.com> Acked-by: Marek Vasut <marex@denx.de>
2015-02-24ARM: remove cm4008 and cm41xx board supportMasahiro Yamada
These are still non-generic boards. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Greg Ungerer <greg.ungerer@opengear.com> Acked-by: Marek Vasut <marex@denx.de>
2015-02-24ARM: remove dkb board supportMasahiro Yamada
This is still a non-generic board. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Lei Wen <leiwen@marvell.com> Acked-by: Marek Vasut <marex@denx.de>
2015-02-24ARM: remove jadecpu board supportMasahiro Yamada
This is still a non-generic board. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Matthias Weisser <weisserm@arcor.de> Acked-by: Marek Vasut <marex@denx.de>
2015-02-24OMAP3: igep0032: Fix regression due commit f3b4bc45.Enric Balletbo i Serra
Commit referenced in subject breaks IGEP0032 build with the following error: drivers/misc/status_led.c:30:7: error: 'RED_LED_GPIO' undeclared here (not in a function) scripts/Makefile.build:275: recipe for target 'drivers/misc/status_led.o' failed make[2]: *** [drivers/misc/status_led.o] Error 1 scripts/Makefile.build:420: recipe for target 'drivers/misc' failed make[1]: *** [drivers/misc] Error 2 Makefile:1093: recipe for target 'drivers' failed make: *** [drivers] Error 2 Fix this by skipping the status led on IGEP0032 machine as is not available and throw an error for future machines if the status led is not configured to avoid build breakage. Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
2015-02-24mmc: fsl_esdhc: Add support for DDR modeVolodymyr Riazantsev
Add support of the DDR mode for eSDHC driver. Enable it for i.MX6 SoC family only. Signed-off-by: Volodymyr Riazantsev <volodymyr.riazantsev@globallogic.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-24arm/ls1021a: add PCIe settingsMinghuan Lian
The patch enables and adds PCIe settings for boards LS1021AQDS and LS1021ATWR. Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-24drivers/mc: Migrated MC Flibs to 0.5.2J. German Rivera
Upgrade Manage Complex (MC) flib API to 0.5.2. Rename directory fsl_mc to fsl-mc. Change the fsl-mc node in Linux device tree from "fsl,dprcr" to "fsl-mc". Print MC version info when appropriate. Signed-off-by: J. German Rivera <German.Rivera@freescale.com> Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-24armv8/ls2085a_emu: Enable sync of refreshYork Sun
Enable sync of DDR refresh for LS2085a platform. GPP DDR controllers stay in sync. DP-DDR has only one controller so it does no harm. Signed-off-by: York Sun <yorksun@freescale.com>
2015-02-24ls2085/configs: Ensure right banners are printed for EMU and SIMUBhupesh Sharma
This patch enusres that right banners are printed for LS2085A emulator and simulator platforms. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-24ARMv8/ls2085a: Move kernel image load addressStuart Yoder
Move the load address of the kernel image to get it away from the region of the uncompressed kernel. Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-24ARMv8/ls2085a: Switch to passing earlycon to kernelArnab Basu
Since Linux v3.16-rc1 earlyprintk has been removed for arm64. Switch to using earlycon. Signed-off-by: Arnab Basu <arnab.basu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
2015-02-24ARMv8/LS2085A: Adjust system clock and DDR clockYork Sun
Set system clock to 100MHz and DDR clock to 133MHz. Signed-off-by: York Sun <yorksun@freescale.com>
2015-02-24ARMv8/LS2085A: HugeTLB support is required by default in LS NADKKuldip Giroh
LS NADK memory manager by default works on HugeTLB. Hence bootargs must include parameters default_hugepagesz (default hugepagesize, hugepagesz (hugepage size) and hugepages (number of hugepages to be reserved in kernel for the given size). Signed-off-by: Kuldip Giroh <kuldip.giroh@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-24fsl-ch3/lowlevel: TZPC and TZASC programming to configure non-secure accessesBhupesh Sharma
This patch ensures that the TZPC (BP147) and TZASC-400 programming happens for LS2085A SoC only when the desired config flags are enabled and ensures that the TZPC programming is done to allow Non-secure (NS) + secure (S) transactions only for DCGF registers. The TZASC component is not present on LS2085A-Rev1, so the TZASC-400 config flag is turned OFF for now. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-02-23warp: Add initial WaRP Board supportOtavio Salvador
The WaRP Board is a Wearable Reference Plaform. The board features: - Freescale i.MX6 SoloLite processor with 512MB of RAM - Freescale FXOS8700CQ 6-axis Xtrinsic sensor - Freescale Kinetis KL16 MCU - Freescale Xtrinsic MMA955xL intelligent motion sensing platform The board implements a hybrid architecture to address the evolving needs of the wearables market. The platform consists of a main board and an example daughtercard with the ability to add additional daughtercards for different usage models. For more information about the project, visit: http://www.warpboard.org/ Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
2015-02-23imx:mx6slevk add pmic and i2c configurationPeng Fan
Add pmic and i2c configuration in board header file. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2015-02-21Merge git://git.denx.de/u-boot-sunxiTom Rini
2015-02-21sunxi: Machine id hack to prevent loading buggy sunxi-3.4 kernelsSiarhei Siamashka
Right now U-Boot supports the CONFIG_OLD_SUNXI_KERNEL_COMPAT option, which makes it go out of its way in limiting the selection of PLL clock frequencies and PMIC voltages in order not to upset outdated buggy sunxi-3.4 kernel releases. And if the CONFIG_OLD_SUNXI_KERNEL_COMPAT option is not set, then booting such old kernels exhibits various failures at runtime. This is very user unfriendly, and there were already several incidents when people wasted their time being hit by these runtime failures and trying to debug them. The right solution is not to add hacks and workarounds to the mainline U-Boot, but to fix these bugs in the sunxi-3.4 kernel. And in fact, the updated sunxi-3.4 kernels already exist. Still we need to follow the 'Principle of Least Surprise' and U-Boot needs to ensure that the old buggy kernels are not getting happily booted when the CONFIG_OLD_SUNXI_KERNEL_COMPAT option is not set. And this patch addresses this particular issue. This patch makes U-Boot store the 'compatibility revision' number in the top 4 bits of the machine id and pass it to the kernel. The old buggy kernels will fail to load with a very much googlable error message on the serial console (the "r1 = 0x100010bb" part of it): "Error: unrecognized/unsupported machine ID (r1 = 0x100010bb)" This error message can be documented in the linux-sunxi wiki with proper explanations about how to resolve this situation and where to get the necessary bugfixes for the sunxi-3.4 kernel. The fixed sunxi-3.4 kernels implement a revision compatibility check and clear the top 4 bits of the machine id if everything is alright. By accepting the machine id with the bits 31:28 set to 1, the sunxi-3.4 kernel effectively certifies that it has the PLL5 clock speed and AXP209 DCDC3 voltage fixes applied. It is still possible to set the CONFIG_OLD_SUNXI_KERNEL_COMPAT option in U-Boot if the user desires to use an outdated unpatched sunxi-3.4 kernel. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-21sunxi: Set the /chosen/stdout-path fdt property for sunxi boardsHans de Goede
While discussing with some people how to get the Linux kernel to do the right thing wrt sending output to both the serial console and the hdmi out / lcd screen when booting on ARM devices, Grant Likely pointed out that there already is a solution for this. All we need to do is set the /chosen/stdout-path fdt property, and if no console= arguments were specified on the kernel commandline the kernel will honor this and add this device as a console (next to the primary video output on hdmi). And u-boot already has support for setting this, all we need to do is define OF_STDOUT_PATH and then everything will just work ootb, without people needing to meddle with adding console= arguments in extlinux.conf . Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Tom Rini <trini@ti.com>
2015-02-21rpi: add support for Raspberry Pi 2 model BStephen Warren
USB doesn't seem to work yet; the controller detects the on-board Hub/ Ethernet device but can't read the descriptors from it. I haven't investigated yet. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-02-21bcm2835/rpi: add SPDX license tags for some filesStephen Warren
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-02-21ARM: kirkwood: move SoC headers to mach-kirkwood/include/machMasahiro Yamada
Move arch/arm/include/asm/arch-kirkwood/* -> arch/arm/mach-kirkwood/include/mach/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Stefan Roese <sr@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-02-21ARM: at91: collect SoC sources into mach-at91Masahiro Yamada
This commit moves source files as follows: arch/arm/cpu/arm920t/at91/* -> arch/arm/mach-at91/arm920t/* arch/arm/cpu/arm926ejs/at91/* -> arch/arm/mach-at91/arm926ejs/* arch/arm/cpu/armv7/at91/* -> arch/arm/mach-at91/armv7/* arch/arm/cpu/at91-common/* -> arch/arm/mach-at91/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Andreas Bießmann <andreas.devel@googlemail.co>
2015-02-20sunxi: video: Add support for LCD panels which need to be configured via i2cHans de Goede
This commits adds support for configuring a a bitbang i2c controller, which is used on some boards to configure the LCD panel (via i2c). Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-19dm: mx6: Adjust mx6sxsabresd to use Kconfig for DM_THERMALSimon Glass
Use Kconfig instead of board config for DM and DM_THERMAL. Signed-off-by: Simon Glass <sjg@chromium.org>
2015-02-19dm: Move CONFIG_I2C_COMPAT to KconfigSimon Glass
Make this option available in Kconfig and clean up the board that uses it. Note there is also an entry in exynos5-common.h but this affects multiple boards and should be dropped as part of the Samsung I2C migration to driver model. Signed-off-by: Simon Glass <sjg@chromium.org>
2015-02-19dm: cros_ec: Convert to KconfigSimon Glass
Since both I2C and SPI are converted to Kconfig, we can convert cros_ec to Kconfig for these buses. LPC will need to wait until driver mode PCI is available. Signed-off-by: Simon Glass <sjg@chromium.org>
2015-02-17Merge branch 'master' of git://git.denx.de/u-boot-avr32Tom Rini
2015-02-17atstk1002: enable generic boardAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-02-17grasshopper: enable generic boardAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>