summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2018-11-26board: da8xxevm: Fix Environmental CRC errorAdam Ford
When the spi_flash_probe_bus_cs() was previously called, it was called using 0's for two values where CONFIG_ENV_SPI_MAX_HZ and CONFIG_ENV_SPI_MODE are now used. When changed this caused the environment to fail the CRC check and the default was used. This patch defines both of these values back 0. Fixes: 25a17652c9c2 ("fix: env: Fix the SPI flash device setup for DM mode") Signed-off-by: Adam Ford <aford173@gmail.com>
2018-11-26armv7r: K3: Allow SPL to run only on core 0Lokesh Vutla
Based on the MCU R5 efuse settings, R5F cores in MCU domain either work in split mode or in lock step mode. If efuse settings are in lockstep mode: ROM release R5 cores and SPL continues to run on the R5 core is lockstep mode. If efuse settings are in split mode: ROM releases both the R5 cores simultaneously and allow SPL to run on both the cores. In this case it is bootloader's responsibility to detect core 1 and park it. Else both the core will be running bootloader independently which might result in an unexpected behaviour. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2018-11-26ARM: meson: Add boot device discoveryNeil Armstrong
The Amlogic Meson SoCs ROM supports a boot over USB with a custom protocol. When no other boot medium are available (or by forcing the USB mode), the ROM sets the primary USB port as device mode and waits for a Host to enumerate. When enumerated, a custom protocol described at [1] permits writing to memory and execute some specific FIP init code to run the loaded Arm Trusted Firmware BL2 and BL3 stages before running the BL33 stage. In this mode, we can load different binaries that can be used by U-boot like a script image file. This adds support for a custom USB boot stage only available when the boot mode is USB and the script file at a pre-defined address is valid. This support was heavily copied from the Sunxi Allwinner FEL U-Boot support. The tool pyamlboot described at [2], permits using this boot mode on boards exposing the first USB port, either as OTG or Host port. [1] https://github.com/superna9999/pyamlboot/blob/master/PROTOCOL.md [2] https://github.com/superna9999/pyamlboot/blob/master/README.md Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-11-26ARM: meson: Add support for AXG familyNeil Armstrong
This patch adds support for the Amlogic AXG SoC, which is very close from the Amlogic GXL SoCs with : - Same 4xCortex-A53 CPUs but clocked at 1.2GHZ max - DDR Interface limited to DDR4 16bit - The whole physical register address space has been moved to 0xfxxxxxxx - The pinctrl setup has changed - The clock tree is different enough to use a different driver Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-11-26configs: meson: change default load addressesJerome Brunet
The original chosen addresses conflict with the BL2 initialisation. So far there was no issue with them but if we preload binaries in RAM (ROMUSB boot) before running the BL2 they get corrupted by the execution of BL2 init. If we load them around 0x08000000, there is no such issue. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-11-26ARM: rework amlogic configurationJerome Brunet
Rework the board SYS_BOARD, SYS_VENDOR and SYS_CONFIG_NAME setup by moving the board Kconfig into the mach-meson Kconfig to make it easier to add new boards for a SoC architecture and add a custom config header or custom board handler for a platform. This drops the board CONFIGs and the duplicate boards configs headers in favor of a single meson64.h config header. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-11-26board: amlogic: move khadas-vim2 as q200 ref boardNeil Armstrong
The Khadas vim2 derive from amlogic s912 reference design (Q200). This patch moves the khadas-vim2 board support to a generic Q200 board, while keeping a dedicated defconfig to customize the names and device tree. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-11-26configs: meson: remove unnecessary MESON_FDTFILE_SETTINGJerome Brunet
MESON_FDTFILE_SETTING is used to define the default name of the fdt file in u-boot environment. We can easily derive it from CONFIG_DEFAULT_DEVICE_TREE instead. This will help factorize the code a bit Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-11-26riscv: qemu: detect and boot the kernel passed by QEMULukas Auer
QEMU embeds the location of the kernel image in the device tree. Store this address in the environment as variable kernel_start. It is used in the board-local distro boot command QEMU to boot the kernel with the U-Boot device tree. The QEMU boot command is added as the first boot target device. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alexander Graf <agraf@suse.de>
2018-11-26riscv: qemu: enable distro bootLukas Auer
Enable distro boot on the qemu-riscv32/64 boards. Supported boot target devices are VirtIO and DHCP. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alexander Graf <agraf@suse.de>
2018-11-26riscv: qemu: support booting LinuxLukas Auer
Support booting Linux (as payload of BBL) from FIT images. For this, the default CONFIG_SYS_BOOTM_LEN is increased to 16 MB, and the environment variables fdt_high and initrd_high are set to mark the device tree and initrd as in-place. Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-11-20ARM: mvebu: db-88f6820: remove redundant commentChris Packham
After migration to Kconfig the comment about TEXT_BASE has become redundant. Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-11-18mips: mt76xx: linkit-smart-7688: Misc updates to dts/config/defconfigStefan Roese
These misc updates include the following changes: - Change baudrate from 57600 to 115200 - Enable MIPS_BOOT_CMDLINE_LEGACY - Enable FIT support - Enable ethernet support - Enable SPI support - Enable GPIO support - Change max image size from 0x40000 to 0x80000 A note about the baudrate change: The original Mediatek U-Boot version used 57600 baud. Lets move to a more common and faster speed of 115200 baud. And remove the "console=" property from the DT as its not needed. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-11-18mips: mt76xx: gardena-smart-gateway: Misc updates to dts/config/defconfigStefan Roese
These misc updates include the following changes: - Change baudrate from 57600 to 115200 - Enable MIPS_BOOT_CMDLINE_LEGACY - Enable FIT support - Enable ethernet support - Enable SPI NOR and NAND support - Change MTD_UBI_BEB_LIMIT to 22 - Enable MTD Support - Enable GPIO support - Enable watchdog support - Enable bootcounter support - Enable version variable - Change max image size from 0x80000 to 0xa0000 - Change SYS_MALLOC_LEN to 16MiB (because of UBI/UBIFS) Signed-off-by: Stefan Roese <sr@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-11-16board: ti: am654: r5: Add initial support for am654Lokesh Vutla
Add initial support for AM654 based EVM running on R5. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
2018-11-16configs: am3517_evm: Use default OMAP3 memory settingsAdam Ford
The AM3517 is mostly am omap3, so this partch removes the custom memory configurations and just uses the default common entries for omap3 and armv7. Signed-off-by: Adam Ford <aford173@gmail.com>
2018-11-16bcm968580xref: add initial supportPhilippe Reynes
This add the initial support of the broadcom reference board bcm968580xref with a bcm6858 SoC. This board has 512 MB of ram, 256 MB of flash (nand), 2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN). Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2018-11-16arm: at91: wdt: Convert watchdog driver to dm/dtPrasanthi Chellakumar
Convert the Watchdog driver for AT91SAM9x processors to support the driver model and device tree. Changes "CONFIG_AT91SAM9_WATCHDOG" to new "CONFIG_WDT_AT91" Kconfig option. Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
2018-11-14Merge branch 'next'Tom Rini
This brings in the u-boot-net PR from Joe.
2018-11-14configs: Migrate and re-enabled CONFIG_CMD_MTDPARTSTom Rini
Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms that had been enabling it turn it on by hand. This exposed that we had not yet migrated CMD_MTDPARTS fully, so do so now. Fixes: 86dfa556d927 ("cmd: ubi: Remove useless call to mtdparts_init()") Signed-off-by: Tom Rini <trini@konsulko.com>
2018-11-07arm: zynq: Setup non zero SPL FIT load addressMichal Simek
Default setup is 0 which is incorrect place because it points to OCM which is allocated for SPL only in our case. Use address in DDR. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-05configs: net: convert DRIVER_TI_KEYSTONE_NET kconfigGrygorii Strashko
Convert DRIVER_TI_KEYSTONE_NET to Kconfig. Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
2018-11-02Merge tag 'arc-for-2018.11' of git://git.denx.de/u-boot-arcTom Rini
Just 2 non-functinal changes: 1. Rename of EMDK to EMSDP so it matches real marketing name 2. Add essential README for IoTDK
2018-11-01emdk->emsdp: Rename boardAlexey Brodkin
Real marketing name of the board was recently updated so to accommodate that change renaming the board and all related to it. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-11-01configs: at91: at91sam9x5ek: fix bootcmd for NAND flashEugen.Hristev@microchip.com
The default bootcommand needs to be accurate w.r.t the nand memory map at http://www.at91.com/linux4sam/bin/view/Linux4SAM/AT91sam9x5ekMainPage#NAND_Flash_demo_Memory_map Updated to load kernel + dtb at right offsets and boot the zImage. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-10-31arm: socfpga: Fix bootcounter located at the end of internal SRAMStefan Roese
Commit 768f23dc8ae3 ("ARM: socfpga: Put stack at the end of SRAM") broke those socfpga boards that keep the bootcounter at the end of the internal SRAM as the bootcounter needs 8 bytes by default and thus the very first SPL call to board_init_f_alloc_reserve overwrites the bootcounter. This patch allows to move the initial stack pointer down a bit by checking if CONFIG_SYS_BOOTCOUNT_ADDR is located in the internal SRAM area and then using this address as location for the start of the stack pointer. No new macros / defines are added by this approach. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2018-10-28x86: theadorable-x86: Generate and pass root=PARTUUID instead of /dev/sdaXStefan Roese
To enable the root device selection (kernel cmd-line) via PARTUUID, this patch enables CMD_PART on all missing theadorable-x86 boards and changes the default environment to generate the root=PARTUUID string automatically. This fixes problems that have been noticed on systems with multiple SATA/AHCI controller connected via PCIe, where the device name for the root device / partition (/dev/sdaX) was incorrect. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-10-28x86: theadorable-x86-common: Change pci hotplug cmdline parameters (again)Stefan Roese
This is needed for the PCIe hotplug to work correctly on some boards with the newer Linux kernel versions. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-10-25Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini
2018-10-25Merge tag 'u-boot-imx-20181025' of git://git.denx.de/u-boot-imxTom Rini
Merged imx8 architecture, fix build for imx8 + warnings
2018-10-24configs: migrate CONFIG_PHY_AQUANTIA to KconfigJeremy Gebben
The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-10-22ARM: omap3_logic: Add NOR Flash Support for SOM-LVAdam Ford
The DM37 and OMAP35 SOM-LV SOM-LV products both support a NOR flash part connected to CS2 in addition to the NAND part on CS0. This patch setups the GPMC timings for the MT28 NOR Flash and enables the CFI-Flash driver now that the CFI stuff is in Kconfig Signed-off-by: Adam Ford <aford173@gmail.com>
2018-10-22arm: udoo: Convert to distro configMeul, Dirk
Instead of keeping a custom environment, use a more generic approach by switching to distro config. Signed-off-by: Dirk Meul <dirk.meul@rwth-aachen.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2018-10-22warp7: include: configs: set skip low level initRui Miguel Silva
If we have defined the OPTEE ram size and not OPTEE means that we are in the case where OPTEE is loaded already (maybe by ARM Trusted Firmware) and that most of the low level initialization is already done and that we may/should skip it doing them here. Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: u-boot@lists.denx.de
2018-10-22Kconfig: Convert CONFIG_IMX_WATCHDOG to KconfigXiaoliang Yang
Move this option to Kconfig and tidy up the config file of eight boards which use it. Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
2018-10-22imx: add i.MX8QXP MEK board supportPeng Fan
Add i.MX8QXP MEK board support Enabled pinctrl/clk/power-domain/mmc/i2c/fec driver. Added README file. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Anatolij Gustschin <agust@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-10-19Convert CONFIG_FLASH_CFI_DRIVER et al to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-19work_92105: remove unused CONFIG_SPL_NAND_BOOT configuration optionVladimir Zapolskiy
The option is unused, SPL image gets a wanted boot device by standard spl_boot_device() call. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
2018-10-19work_92105: remove unused CONFIG_LPC32XX_SPL configuration optionVladimir Zapolskiy
The CONFIG_LPC32XX_SPL option from board include file has never been used, it is safe to remove it. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
2018-10-18ARM: rmobile: Enable cache command on Gen3Hiroyuki Yokoyama
This patch enables the cache command, mostly for convenience of testing. Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2018-10-16arm64: versal: Add support for new Xilinx Versal ACAPsMichal Simek
Xilinx is introducing Versal, an adaptive compute acceleration platform (ACAP), built on 7nm FinFET process technology. Versal ACAPs combine Scalar Processing Engines, Adaptable Hardware Engines, and Intelligent Engines with leading-edge memory and interfacing technologies to deliver powerful heterogeneous acceleration for any application. The Versal AI Core series has five devices, offering 128 to 400 AI Engines. The series includes dual-core Arm Cortex™-A72 application processors, dual-core Arm Cortex-R5 real-time processors, 256KB of on-chip memory with ECC, more than 1,900 DSP engines optimized for high-precision floating point with low latency. The patch is adding necessary infrastructure in place without enabling platform which is done in separate patch. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-10-16arm: mx5: Add M53Menlo boardMarek Vasut
Add Menlosystems M53 board, based on the M53 SoM. This board has Ethernet, USB host, USB gadget, UART and LCD on it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2018-10-12Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
2018-10-10Merge tag 'dm-9oct18' of git://git.denx.de/u-boot-dmTom Rini
Test improvements to tidy up output and drop duplicate tests Sandbox SPL/TPL support Various dm-related improvements
2018-10-10ARM: meson: Add Khadas VIM2 board supportLoic Devulder
This adds platform code for the Khadas VIM2 board based on a Meson GXM (S912) SoC with the Meson GXM configuration. This initial submission supports UART, MMC/SDCard and Ethernet. USB is partially supported. All the code is from Neil Armstrong! I just rebased the code, do some cleanup and tested on my board. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Loic Devulder <ldevulder@suse.de> Acked-by: Neil Armstrong <narmstrong@baylibre.com>
2018-10-10board: da8xxevm: Add SPL DM for serial, spiJagan Teki
This patch add SPL DM support for da8xxevm boards with SPL serial, SPI drivers supported via platdata. Cc: Adam Ford <aford173@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Adam Ford <aford173@gmail.com> #da850evm
2018-10-09configs: mx7: Remove CONFIG_DBG_MONITORFabio Estevam
Remove all CONFIG_DBG_MONITOR references as it is not used anywhere. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2018-10-09colibri_imx7: prime get_ram_size() using imx_ddr_size()Fabio Estevam
Rather than passing a hardcoded maxsize to the generic get_ram_size() function use the i.MX 7 specific imx_ddr_size() function, which extracts the memory size at runtime by reading the DDR controller registers. This is a purely cosmetic change as the generic get_ram_size() function already took care of properly automatically detecting 256MB, 512MB or 1GB modules. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Stefan Agner <stefan.agner@toradex.com>
2018-10-09pico-imx6ul, pico-imx7d: Enable USB and PXE boot supportOtavio Salvador
This allow the use of a USB storage or PXE network booting as fallback, allowing for example for manufacturing installation of eMMC storage in an easy way. Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-10-09pico-imx6ul, pico-imx7d: Use eMMC user partition by defaultOtavio Salvador
After discussing with TechNexion about how its default setting, it is better to install on the eMMC user partition by default, when using DFU, so it works out of box for majority of users. Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
generated by cgit (git 2.34.1) at 2025-01-01 14:06:35 +0000