summaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)Author
2016-04-01Migrate CONFIG_ULPI* to KconfigMateusz Kulikowski
Move CONFIG_USB_ULPI* from headers to defconfigs for boards that use it. Also - add CONFIG_USB where necesarry - all boards use it, but some are not defining it explicitly. Affected boards: colibri_t20, harmony, mcx, mt_ventoux, twister, zynq_(picozed, zc702, zc706, zed, zybo) Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-04-01board: ti: DRA7: Add DP83867 TI phy for rev cDan Murphy
Enable the TI DP83867 Giga bit phy on the dra7 rev c board. The rx and tx internal delays are need for this board so the usage of RGMII_ID is required. Signed-off-by: Dan Murphy <dmurphy@ti.com> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01kc1: Add some sysboot and devicetree-related environment variablesPaul Kocialkowski
This adds some environment variables for sysboot and devicetree. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-04-01kc1: Include explicit serial baudrate on bootargsPaul Kocialkowski
This makes the baudrate for the kernel command line explicit. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-04-01sniper: Include explicit serial baudrate on bootargsPaul Kocialkowski
This makes the baudrate for the kernel command line explicit. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-04-01configs: ti_armv7_keystone2: make SYS_TEXT_BASE configurable at build timeVitaly Andrianov
U-boot for general purpose KS2 devices is loaded to the beginning of the internal memory (0x0c000000). Secure devices uses this memory and CONFIG_SYS_TEXT_BASE has to be different for those devices. This commit make this configurable at build time by giving CONFIG_SYS_TEXT_BASE as a command line definition to make command. Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
2016-04-01rpi: BCM2837 and Raspberry Pi 3 32-bit supportStephen Warren
The Raspberry Pi 3 contains a BCM2837 SoC. The BCM2837 is a BCM2836 with the CPU complex swapped out for a quad-core ARMv8. This can operate in 32- or 64-bit mode. 32-bit mode is the current default selected by the VideoCore firmware on the Raspberry Pi 3. This patch adds a 32-bit port of U-Boot for the Raspberry Pi 3. >From U-Boot's perspective, the only delta between the RPi 2 and RPi 3 is a change in usage of the SoC UARTs. On all previous Pis, the PL011 was the only UART in use. The Raspberry Pi 3 adds a Bluetooth module which uses a UART to connect to the SoC. By default, the PL011 is used for this purpose since it has larger FIFOs than the other "mini" UART. However, this can be configured via the VideoCore firmware's config.txt file. This patch hard-codes use of the mini UART in the RPi 3 port. If your system uses the PL011 UART for the console even on the RPi 3, please use the RPi 2 U-Boot port instead. A future change might determine which UART to use at run-time, thus allowing the RPi 2 and RPi 3 (32-bit) ports to be squashed together. The mini UART has some limitations. One externally visible issue in the BCM2837 integration is that the UART divides the SoC's "core clock" to generate the baud rate. The core clock is typically variable, and under control of the VideoCore firmware for thermal management reasons. If the VC FW does modify the core clock rate, UART communication will be corrupted since the baud rate will vary from the expected value. This was not an issue for the PL011 UART, since it is fed by a fixed 3MHz clock. To work around this, the VideoCore firmware can be told not to modify the SoC core clock. However, the only way this can happen and be thermally safe is to limit the core clock to a low/minimum frequency. This leaves performance on the table for use-cases that don't care about a UART console. Consequently, use of the mini UART console must be explicitly requested by entering the following line into config.txt: enable_uart=1 A recent version of the VC firmware is required to ensure that the mini UART is fully and correctly initialized by the VC FW; at least firmware.git 046effa13ebc "firmware: arm_loader: emmc clock depends on core clock See: https://github.com/raspberrypi/firmware/issues/572". Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01ARM: bcm2835: move CONFIG_BCM283* to KconfigStephen Warren
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini
2016-04-01sunxi: Add support for Allwinner A64 SoCsSiarhei Siamashka
The Allwinner A64 SoC is used in the Pine64. This patch adds all bits necessary to compile U-Boot for it running in AArch64 mode. Unfortunately SPL is not ready yet due to legal problems, so we need to boot using the binary boot0 for now. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> [agraf: remove SPL code, move to AArch64] Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01ARM: uniphier: remove CONFIG_ARP_TIMEOUT defineMasahiro Yamada
I no longer see the problem claimed in the comment block. Rather, the 0.5 msec timeout seems too short for some TFTP servers. Drop the CONFIG_ARM_TIMEOUT to fall back to the 5 sec timeout. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01ARM: uniphier: drop unneeded defines related to legacy serial driverMasahiro Yamada
These defined were used for pre-DM ns16550 serial driver. They are unneeded because UniPhier SoCs now use DM serial. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01ARM: uniphier: add sramupdate commandMasahiro Yamada
This command would be useful to update U-Boot images in SRAM. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01ARM: uniphier: make u-boot-with-spl.bin really availableMasahiro Yamada
Commit d085ecd61b99 ("ARM: uniphier: switch to raw U-Boot image") claimed that u-boot-with-spl.bin would be useful in its commit log, but it was not available because the commit missed to define CONFIG_SPL_MAX_SIZE. Without it, CONFIG_SPL_PAD_TO is not defined either (see include/config_fallbacks.h). So, the SPL image is not padded correctly. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-31sunxi: usb_phy: Add support for A83T USB PHYsChen-Yu Tsai
The A83T has 3 USB PHYs: 1 for USB OTG, 1 for standard USB 1.1/2.0 host, 1 for USB HSIC. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-29Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
2016-03-29armv8/ls2080ardb: Enable VID supportRai Harninder
This patch enable VID support for ls2080ardb platform. It uses the common VID driver. Signed-off-by: Rai Harninder <harninder.rai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29armv8: ls2080rdb: ls2080qds: Add secure boot supportSaksham Jain
Sec_init has been called at the beginning to initialize SEC Block (CAAM) which is used by secure boot validation later for both ls2080a qds and rdb. 64-bit address in ESBC Header has been enabled. Secure boot defconfigs are created for boards (NOR boot). Signed-off-by: Saksham Jain <saksham.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-27zipitz2: enable cachesVasily Khoruzhick
It speeds up loading kernel from SD or USB a lot. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
2016-03-27pxa: add support for D- and I- cachesVasily Khoruzhick
Tested with OHCI and pxafb drivers - no issues found Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
2016-03-27zipitz2: enable USB host supportVasily Khoruzhick
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
2016-03-27pxa-common: pxa27x has 3 OHCI portsVasily Khoruzhick
3rd port can be used as a device or host. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
2016-03-27zipitz2: enable libfdtVasily Khoruzhick
zipitz2 supports DT boot since linux-4.4 (not mainlined yet) Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
2016-03-27zipitz2: enable LCD rotationVasily Khoruzhick
z2's screen is rotated by 270 degrees Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
2016-03-27zipitz2: restore board supportVasily Khoruzhick
zipitz2 was dropped in 49d8899ba9c26335e4a12e01c18028fc5e40c796 Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
2016-03-27ARM: bcm283x: don't always define CONFIG_BCM2835Stephen Warren
Currently, CONFIG_BCM2835 is defined for all BCM283x builds and _BCM2836 is defined when building for that SoC. That means there isn't a single define that means "exactly BCM2835". This will complicate future patches where BCM2835-vs-anything-else needs to be determined simply. Modify the code to define one or the other of CONFIG_BCM2835/BCM2836 so future patches are simpler. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27RPi: Enable caches for rpi2Alexander Graf
Now that we have support for running with caches enabled in HYP mode, opt in to that on the Raspberry Pi 2. This brings a significant performance boost. Signed-off-by: Alexander Graf <agraf@suse.de>
2016-03-26stm32f746-disco: enable flash supportVikas Manocha
This patch enables embedded flash for stm32f746 discovery board. Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2016-03-26stm32: stm32f4: move flash driver to mtd driver locationVikas Manocha
Same flash driver can be used by other stm32 families like stm32f7. Better place for this driver would be mtd driver location. Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2016-03-26arm: mx6: Add CCV xPress board supportStefan Roese
This patch add support for the CCV xPress board which is equipped with the i.MX6UL. And provides the following interfaces: - 128MiB DDR - UART - I2C - eMMC (with booting) - Ethernet - USB This patch adds two build targets. One with and one without SPL. The non-SPL version is used for loading U-Boot via USB (imx_usb_loader). Signed-off-by: Stefan Roese <sr@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-03-26warp7: Add initial supportFabio Estevam
Add the basic support for Warp7 board. For more information about this reference design, please visit: https://www.element14.com/community/docs/DOC-79058/l/warp-7-the-next-generation-wearable-reference-platform Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2016-03-26mx7_common: Put early/late init configs into board fileFabio Estevam
CONFIG_BOARD_EARLY_INIT_F and CONFIG_BOARD_LATE_INIT should not be placed into mx7_common because not all boards need these options. Move them to the board file instead. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2016-03-25usb: gadget: Move CONFIG_USB_GADGET to KconfigSam Protsenko
The description was borrowed from kernel. "tristate" type was changed to "bool" (I believe we don't support modules for u-boot yet, right?). CONFIG_USB_GADGET requires CONFIG_USB to be defined too, so add it along as well. Definitions were added to defconfig files in a way that "make savedefconfig" generates exactly the same file as used defconfig. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> [trini: Add zynq_zc702 conversion] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-25Merge git://www.denx.de/git/u-boot-marvellTom Rini
2016-03-25mx6sabre_common: Fix U-Boot corruption after 'saveenv'Fabio Estevam
Booting mx6qp sabreauto board and then doing: => saveenv => reset , causes a system hang. This happens because the size of the U-Boot binary is larger than CONFIG_ENV_OFFSET. Fix this problem by increasing CONFIG_ENV_OFFSET, so that the U-boot binary and the environment variables region do not overlap. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-03-25arm: mx5: Enable NAND TrimFFS on M53EVKMarek Vasut
Enable NAND TrimFFS support in M53EVK, since it is convenient when installing UBI images to NAND. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2016-03-24armv8/ls1043a: Update env settings for booting kernelQianyu Gong
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-24arm: mvebu: theadorable: Add StratixV FPGA programming supportStefan Roese
This patch adds support for Altera StratixV bitstream programming. 2 FPGAs are connected to the SPI busses. This patch uses board specific write code to program the bitstream via SPI direct write mode. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Signed-off-by: Stefan Roese <sr@denx.de>
2016-03-24ARM: sheevaplug: correct nand partition layoutPeter Korsgaard
Commit 1e3d640316 (ARM: sheevaplug: redefine MTDPARTS) changed the partition layout (without any description why), but didn't change the offset/size to load the kernel from or the root=/dev/mtdblockX in the bootargs. The 3MB forseen for a kernel is furthermore too little. A 4.4 build of mvebu_v5_defconfig is 3.6MB: -rw-r--r-- 1 peko peko 3.6M Jan 16 20:24 uImage.kirkwood-sheevaplug When device tree support for sheevaplug was added to the kernel in commit ee514b381e (ARM: Kirkwood: Add dts files for Sheevaplug and eSATA Sheevaplug) a default flash partition layout (used if mtdparts= isn't passed on the command line / CONFIG_MTD_CMDLINE_PARTS isn't enabled) with 1MB for u-boot / environment, 4MB for the kernel and the rest for the rootfs, so use that layout here and adjust the kernel loading to match. Signed-off-by: Peter Korsgaard <peter@korsgaard.com> Signed-off-by: Stefan Roese <sr@denx.de>
2016-03-23Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini
2016-03-23sunxi: Enable realtek phy supportHans de Goede
Enable building of drivers/net/phy/realtek.c so that realtek phys get properly initialized. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-24ARM: uniphier: switch to raw U-Boot imageMasahiro Yamada
Now everything is done to load a raw U-Boot proper image instead of an mkimage-processed one (as far as I tested on NAND, eMMC, NOR). The SPL already knows the load address of the U-Boot proper without parsing its uImage header because the load address is defined by CONFIG_SYS_TEXT_BASE, assuming that the two images are generated from the same build. My main motivation of this switch is to use u-boot-with-spl.bin, a concatenation of u-boot-spl.bin and u-boot.bin. (I wish there were a concatenation of u-boot-spl.bin and u-boot.img...) Anyway, this commit would be useful for one-shot image burn. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-24ARM: uniphier: add NOR boot supportMasahiro Yamada
This allows to boot from NOR flash (or SRAM) with help of an external loader (NOR-loader). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-24ARM: uniphier: drop PH1- prefix from CONFIG options and file namesMasahiro Yamada
The current CONFIG names like "CONFIG_ARCH_UNIPHIER_PH1_PRO4" is too long. It would not hurt to drop "PH1_" because "UNIPHIER_" already well specifies the SoC family. Also, rename files for consistency. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-24ARM: uniphier: fix bogus commentMasahiro Yamada
This comment line is telling the opposite of the logic. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-24ARM: uniphier: remove commented out defineMasahiro Yamada
This TODO is no longer useful. CONFIG_SYS_NS16550_SERIAL is just ignored on DM serial. If one wants to use the 16550A UART device on the UniPhier Micro Support Card, it can be enabled by CONFIG_SYS_NS16550 via Kconfig. Please notice CONFIG_SPL_OF_TRANSLATE must be enabled as well and the device tree must be treaked in order to use the NS16550 serial on SPL. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-22net: Move CONFIG_RTL8169 to KconfigBin Meng
Introduce CONFIG_RTL8169 in Kconfig and move over boards' defconfig to use that. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Stephen Warren <swaren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-03-22net: Move CONFIG_RTL8139 to KconfigBin Meng
Introduce CONFIG_RTL8139 in Kconfig and move over boards' defconfig to use that. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> [trini: Fixup MPC8641HPCN* and r2dplus configs] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-22ti: k2g: increase phy autoneg timeoutVitaly Andrianov
After power cycle of a K2G EVM dhcp fails due to a auto-negotiation timeout. This commit increases the timeout to fix the issue. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-22Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini
generated by cgit (git 2.34.1) at 2024-12-28 00:48:35 +0000