summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2014-05-16drivers/usb : Define usb control register mask for w1c bitsNikhil Badola
Define and use CONTROL_REGISTER_W1C_MASK to make sure that w1c bits of usb control register do not get reset while writing any other bit Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-05-16powerpc/85xx: Add T4160RDB board supportChunhe Lan
T4160RDB shares the same platform as T4240RDB. T4160 is a low power version of T4240, with the eight e6500 cores, two DDR3 controllers, and same peripheral bus interfaces. Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-05-16Merge remote-tracking branch 'u-boot-sh/rmobile'Albert ARIBAUD
Conflicts: boards.cfg Trivial conflict, maintainer change plus board addition
2014-05-16Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-05-16Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-05-16ARM: exynos4: enable the dwmmc configurationJaehoon Chung
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16mmc: dw_mmc: support the DDR modeJaehoon Chung
Support the DDR mode at dw-mmc controller Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16mmc: support the DDR mode for eMMCJaehoon Chung
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16mmc: remove the unnecessary define and fix the wrong bit controlJaehoon Chung
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Lukasz Majeski <l.majewski@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16mmc: exynos_dw_mmc: restore the property into hostJaehoon Chung
Restore the platdata(property of dt) into host struct. Then data's information is maintained and reused anywhere. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16ARM: dts: exynos: rename from EXYNOS5_DWMMC to EXYNOS_DWMMCJaehoon Chung
Exynos serise can be supported the dw-mmc controller. So, it's good that used the general prefix as "_EXYNOS_DWMMC". Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16arm: goni: enable USB Mass StorageMateusz Zalega
UMS-related defines were added to Samsung Goni config header. Signed-off-by: Mateusz Zalega <m.zalega@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16arm: goni: enable GPT commandMateusz Zalega
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16arm: goni: dfu: Add support for DFU to Goni targetMateusz Zalega
Proper adjustment for supporting DFU at GONI target has been made. The s5p_goni.h file has been updated. Moreover the code for low level USB initialization has been added to GONI board code. The malloc pool has been enlarged in order to support larger buffer sizes needed by DFU implementation. Signed-off-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mateusz Zalega <m.zalega@samsung.com> Tested-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com> Tested-by: Mateusz Zalega <m.zalega@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-16arm: goni: Update configuration for Goni targetMateusz Zalega
Configuration file for GONI has been updated to support FAT file system, new mmc partitioning scheme and read linux kernel from eMMC instead of OneNAND. Signed-off-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mateusz Zalega <m.zalega@samsung.com> Tested-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com> Tested-by: Mateusz Zalega <m.zalega@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2014-05-15Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-05-15Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-05-15zynq: load u-boot-dtb.img if CONFIG_OF_SEPARATE is definedMasahiro Yamada
SPL should load "u-boot-dtb.img" if both CONFIG_OF_CONTROL and CONFIG_OF_SEPARATE are defined. Otherwise, "u-boot.img" should be loaded. Since CONFIG_OF_CONTROL is always undefined for SPL_BUILD, the undef block should be moved below the conditional definition of CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-15Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic
2014-05-15dfu: mmc: Provide support for eMMC boot partition accessLukasz Majewski
Before this patch it was only possible to access the default eMMC HW partition. By partition selection I mean the access to eMMC via the ext_csd[179] register programming. It sometimes happens that it is necessary to write to other partitions. This patch adds extra attribute to "raw" sub type of the dfu_alt_info environment variable (e.g. boot-mmc.bin raw 0x0 0x200 mmcpart 1;) It saves the original boot value and restores it after storing the file. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
2014-05-15Merge remote-tracking branch 'u-boot/master' into testMarek Vasut
2014-05-14ARM: zynq: Extend maximum number of command argumentsMichal Simek
15 was too small for variables stored in file on MMC. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14ARM: zynq: Enable EXT4 configsSiva Durga Prasad Paladugu
Enabled the EXT4 configs. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14ARM: zynq: Move USB/SD/MMC common FAT configsSiva Durga Prasad Paladugu
Moved the USB/SD/MMC common FAT configs separately to avoid redefinition warnings. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14ARM: zynq: Enable the FAT write capabilitySiva Durga Prasad Paladugu
Enable the FAT write capability for SD/MMC write functionality. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14ARM: zynq: Added USB host support for zynq boardsSiva Durga Prasad Paladugu
Added configs to support USB host for zynq boards. Also added a command usbboot to boot from usb. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14ARM: zynq: Extend kernel image size to 60MBMichal Simek
Extend max kernel image size. Gunzip is checking this value. If kernel is larger, message below is shown. Uncompressing Kernel Image ... Error: inflate() returned -5 GUNZIP: uncompress, out-of-mem or overwrite error - must RESET board to recover Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-14ARM: zynq: Call zynq board_init() in SPLMichal Simek
Call board_init() if SPL is configured with CONFIG_SPL_BOARD_INIT. Signed-off-by: Michal Simek <monstr@monstr.eu>
2014-05-13am335x: pepper: Add Gumstix Pepper AM335x-based machineAsh Charles
This adds the Gumstix Pepper[1] single-board computer based on the TI AM335x processor. Schematics are available [2]. [1] https://store.gumstix.com/index.php/products/344/ [2] https://pubs.gumstix.com/boards/PEPPER/ Signed-off-by: Ash Charles <ash@gumstix.com> [trini: Move 'cdev' in board.c down to under #ifdef's where it's used] Signed-off-by: Tom Rini <trini@ti.com>
2014-05-13arm, davinci: Use CONFIG_SPL_PAD_TO for padding the SPL in an ais imageChristian Riesch
The commits commit b7b5f1a16ca66dfdd817e7339f0e263a5b9f2758 Author: Albert ARIBAUD <albert.u.boot@aribaud.net> da850evm, da850_am18xxevm: convert to CONFIG_SPL_MAX_FOOTPRINT and commit e7497891e34efe5cb2b3a3dc7c6c096c012ede28 Author: Albert ARIBAUD <albert.u.boot@aribaud.net> cam_enc_4xx: convert to CONFIG_SPL_MAX_FOOTPRINT replaced CONFIG_SPL_MAX_SIZE by CONFIG_SPL_MAX_FOOTPRINT. However, CONFIG_SPL_MAX_SIZE is used in the Makefile for padding the SPL when preparing an u-boot.ais image. By removing CONFIG_SPL_MAX_SIZE said commits broke the ais image of the da850evm and cam_enc_4xx configurations. This patch converts the u-boot.ais target to use CONFIG_SPL_PAD_TO instead of CONFIG_SPL_MAX_SIZE for padding the SPL and adds a #define CONFIG_SPL_PAD_TO where it is required. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Reported-by: Tom Taylor <ttaylor.tampa@gmail.com> Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Cc: Heiko Schocher <hs@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-05-13siemens, draco: add new targetEgli, Samuel
Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Reviewed-by: Roger Meier <r.meier@siemens.com> Cc: Heiko Schocher <hs@denx.de> Cc: Wolfgang Denk <wd@denx.de>
2014-05-13omap3_beagle: xM A/B validate new dtb exits in file systemRobert Nelson
Fall back to previous dtb used when omap3-beagle-xm-ab.dtb doesn't exist in file system Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@ti.com> CC: Nishanth Menon <nm@ti.com> Acked-by: Tom Rini <trini@ti.com>
2014-05-13omap3_beagle: use omap3-beagle-xm-ab.dtb for the xM AB revisionRobert Nelson
As of v3.15-rc3, omap3-beagle-xm-ab.dtb now exists with the usb hub (ehci) enabled. For older kernels versions, cherry pick from mainline: ef78f3869c37c480f1d58462a760a40dabc823f4 Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@ti.com> CC: Nishanth Menon <nm@ti.com>
2014-05-13ARM: OMAP5: Power: add LDO2 support for Palmas driverDmitry Lifshitz
Add defines required to turn on LDO2 regulator. Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
2014-05-13siemens: cosmetic: rename project_dirEgli, Samuel
Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Cc: Roger Meier <r.meier@siemens.com> Cc: Heiko Schocher <hs@denx.de> Cc: Wolfgang Denk <wd@denx.de>
2014-05-13siemens: change LED indication in DFU modeEgli, Samuel
In order to have the same LED indication like in another product when ready for updating, enable only red led and disable status LED when entering DFU mode. The status LED is only switched off when defined in board file. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Cc: Roger Meier <r.meier@siemens.com> Cc: Heiko Schocher <hs@denx.de> Cc: Wolfgang Denk <wd@denx.de>
2014-05-13siemens: cosmetic: remove unused and rename definesEgli, Samuel
For dxr2 board DXR2_IOCTRL_VAL is set by data in EEPROM. In pxm2 board it does not make sense to have dxr2 as prefix. Replace it with more meaningful DDR prefix. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Cc: Pascal Bach <pascal.bach@siemens.com> Cc: Roger Meier <r.meier@siemens.com> Cc: Heiko Schocher <hs@denx.de> Cc: Wolfgang Denk <wd@denx.de>
2014-05-13config: k2hk_evm: Add generic board supportKhoronzhuk, Ivan
We should use generic board in order the ARM maintainer be able to remove arch/arm/lib/board.c Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-05-13Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini
2014-05-13ARM: tegra: use a CPU freq that all SKUs can supportStephen Warren
U-Boot on Tegra30 currently selects a main CPU frequency that cannot be supported at all on some SKUs, and needs higher VDD_CPU/VDD_CORE values on some others. This can result in unreliable operation of the main CPUs. Resolve this by switching to a CPU frequency that can be supported by any SKU. According to the following link, the maximum supported CPU frequency of the slowest Tegra30 SKU is 600MHz: repo http://nv-tegra.nvidia.com/gitweb/?p=linux-2.6.git;a=summary branch l4t/l4t-r16-r2 path arch/arm/mach-tegra/tegra3_dvfs.c table cpu_dvfs_table[] According to that same table, the minimum VDD_CPU required to operate at that frequency across all SKUs is 1.007V. Given the adjustment resolution of the TPS65911 PMIC that's used on all Tegra30-based boards we support, we'll end up using 1.0125V instead. At that VDD_CPU, tegra3_get_core_floor_mv() in that same file dictates that VDD_CORE must be at least 1.2V on all SKUs. According to tegra_core_speedo_mv() (in tegra3_speedo.c in the same source tree), that voltage is safe for all SKUs. An alternative would be to port much of the code from tegra3_dvfs.c and tegra3_speedo.c in the kernel tree mentioned above. That's more work than I want to take on right now. While all the currently supported boards use the same regulator chip for VDD_CPU, different types of regulators are used for VDD_CORE. Hence, we add some small conditional code to select how VDD_CORE is programmed. If this becomes more complex in the future as new boards are added, or we end up adding code to detect the SoC SKU and dynamically determine the allowed frequency and required voltages, we should probably make this a runtime call into a function provided by the board file and/or relevant PMIC driver. Cc: Alban Bedel <alban.bedel@avionic-design.de> Cc: Marcel Ziswiler <marcel@ziswiler.com> Cc: Bard Liao <bardliao@realtek.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13ARM: tegra: set CONFIG_SYS_MMC_MAX_DEVICEStephen Warren
If CONFIG_API is ever to be enabled on Tegra, this define must be set, since api/api_storage.c uses it. A couple of annoyting things about CONFIG_SYS_MMC_MAX_DEVICE 1) It isn't documented in README. The same is true for a lot of similar defines used by api_storage.c. 2) It doesn't represent MAX_DEVICE but rather NUM_DEVICES, since the valid values are 0..n-1 not 0..n. However, I this patch does not address those shortcomings. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13powerpc/freescale: Convert selected boards to generic board architectureYork Sun
This patch converts the following boards to use generic board: MPC8536DS, MPC8572DS, MPC8641HPCN, p1_p2_rdb_pc, corenet_ds, t4qds, B4860QDS. It has been tested on NOR boot on MPC8536DS, MPC8572DS, P1021RDB, P4080DS, P5020DS, P5040DS, P3041DS, T4240QDS, B4860QDS. Signed-off-by: York Sun <yorksun@freescale.com> CC: Ying Zhang <b40530@freescale.com> CC: Prabhakar Kushwaha <prabhakar@freescale.com> CC: Haijun.Zhang <Haijun.Zhang@freescale.com> CC: Scott Wood <scottwood@freescale.com> CC: Shaohui Xie <Shaohui.Xie@freescale.com>
2014-05-13powerpc/mpc85xx: Fix boot_flag for calling board_init_f()York Sun
baord_init_f takes one argument, boot_flag. It has not been used for powerpc, until recently changing to use generic board architecture. The boot flag is added as a return value from cpu_init_f(). Signed-off-by: York Sun <yorksun@freescale.com> CC: Alexander Graf <agraf@suse.de>
2014-05-13powerpc/mpc8572ds: Increase u-boot size to 768KBYork Sun
U-boot image has grown and exceeded the predefined 512KB. Increasing to 768KB to align with other powerpc boards. Tested on MPC8572DS for 32- and 36-bit targets with NOR flash boot. NAND boot is not covered by this patch. Also update board maintainer for these boards. Signed-off-by: York Sun <yorksun@freescale.com> Acked-by: Heiko Schocher <hs@denx.de>
2014-05-13PPC 85xx QEMU: Make a generic board fileAlexander Graf
This patch enables the E500 QEMU board to use the generic cross-arch board infrastructure. Signed-off-by: Alexander Graf <agraf@suse.de>
2014-05-13kmp204x: enable the errata commandValentin Longchamp
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-05-13kmp204x: update the CONFIG_PRAM and CONFIG_KM_RESERVED_PRAM definesValentin Longchamp
This prevents u-boot from accessing into the reserved memory areas that we have for /var and the logbooks. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-05-13kmp204x: selftest/factory test pin supportValentin Longchamp
This patch defines the post_hotkeys_pressed() function that is used for: - triggering POST memory regions test - starting the test application through the checktestboot command in a script by setting the active bank to testbank The post_hotkeys_pressed return the state of the SELFTEST pin. The patch moves from the complete POST-memory test that is too long in its SLOW version for our production HW test procedure to the much shorter POST-memory-regions test. Finally, the unused #defines for the not so relevant mtest command are removed. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-05-13powerpc/t208x: enable errata A006261, A006593, A006379Shengzhou Liu
Enable errata A006261, A006593, A006379 for T208x. Additionally enable CONFIG_CMD_ERRATA for T2080RDB. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2014-05-13powerpc/85xx: Add T4240RDB board supportChunhe Lan
T4240RDB board Specification ---------------------------- Memory subsystem: 6GB DDR3 128MB NOR flash 2GB NAND flash Ethernet: Eight 1G SGMII ports Four 10Gbps SFP+ ports PCIe: Two PCIe slots USB: Two USB2.0 Type A ports SDHC: One SD-card port SATA: One SATA port UART: Dual RJ45 ports Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> [York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
generated by cgit (git 2.34.1) at 2025-01-06 11:29:46 +0000