summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2013-11-13powerpc/t104xrdb: Add T1042RDB_PI board supportPriyanka Jain
T1042RDB_PI is Freescale Reference Design Board supporting the T1042 QorIQ Power Architecture™ processor. T1042 is a reduced personality of T1040 SoC without Integrated 8-port Gigabit. The board is designed with low power features targeted for Printing Image Market. T1042RDB_PI is similar to T1040RDB board with few differences like it has video interface, supports T1042 personality T1042RDB_PI board Overview ----------------------- - Four e5500 cores, each with a private 256 KB L2 cache - 256 KB shared L3 CoreNet platform cache (CPC) - Interconnect CoreNet platform - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: - Packet parsing, classification, and distribution - Queue management for scheduling, packet sequencing, and congestion management - Cryptography Acceleration - RegEx Pattern Matching Acceleration - IEEE Std 1588 support - Hardware buffer management for buffer allocation and deallocation - Ethernet interfaces - Two on-board RGMII 10/100/1G ethernet ports. - SERDES Connections, 8 lanes supporting: — PCI — SATA 2.0 - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and Interleaving -IFC/Local Bus - NAND flash: 1GB 8-bit NAND flash - NOR: 128MB 16-bit NOR Flash - Ethernet - Two on-board RGMII 10/100/1G ethernet ports. - PHY #0 remains powered up during deep-sleep - CPLD - Clocks - System and DDR clock (SYSCLK, “DDRCLK”) - SERDES clocks - Video - DIU supports video at up to 1280x1024x32bpp - HDMI connector - Power Supplies - USB - Supports two USB 2.0 ports with integrated PHYs - Two type A ports with 5V@1.5A per port. - SDHC - SDHC/SDXC connector - SPI - On-board 64MB SPI flash - I2C - Device connected: EEPROM, thermal monitor, VID controller, RTC - Other IO - Two Serial ports - ProfiBus port - Four I2C ports Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
2013-11-13powerpc/t104xrdb: Add T1040RDB board supportPriyanka Jain
T1040RDB is Freescale Reference Design Board supporting the T1040 QorIQ Power Architecture™ processor. T1040RDB board Overview ----------------------- - Four e5500 cores, each with a private 256 KB L2 cache - 256 KB shared L3 CoreNet platform cache (CPC) - Interconnect CoreNet platform - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: - Packet parsing, classification, and distribution - Queue management for scheduling, packet sequencing, and congestion management - Cryptography Acceleration - RegEx Pattern Matching Acceleration - IEEE Std 1588 support - Hardware buffer management for buffer allocation and deallocation - Ethernet interfaces - Integrated 8-port Gigabit Ethernet switch - Four 1 Gbps Ethernet controllers - SERDES Connections, 8 lanes supporting: - PCI - SGMII - QSGMII - SATA 2.0 - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and Interleaving -IFC/Local Bus - NAND flash: 1GB 8-bit NAND flash - NOR: 128MB 16-bit NOR Flash - Ethernet - Two on-board RGMII 10/100/1G ethernet ports. - PHY #0 remains powered up during deep-sleep - CPLD - Clocks - System and DDR clock (SYSCLK, “DDRCLK”) - SERDES clocks - Power Supplies - USB - Supports two USB 2.0 ports with integrated PHYs - Two type A ports with 5V@1.5A per port. - SDHC - SDHC/SDXC connector - SPI - On-board 64MB SPI flash - I2C - Devices connected: EEPROM, thermal monitor, VID controller - Other IO - Two Serial ports - ProfiBus port Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> [York Sun: fixed Makefile] Acked-by: York Sun <yorksun@freescale.com>
2013-11-13powerpc/t1040: enable PBL tool for T1040Prabhakar Kushwaha
Use a default RCW of protocol 0x66. A PBI configure file which uses CPC as 256KB SRAM. It can be used by PBL tool on T1040 to build a pbl boot image. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2013-11-13i2c, zynq: convert zynq i2c driver to new multibus/multiadapter frameworkHeiko Schocher
- add zync i2c driver to new multibus/multiadpater support - adapted all config files, which uses this driver Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Michal Simek <michal.simek@xilinx.com>
2013-11-13i2c, omap24xx: convert driver to new mutlibus/mutliadapter frameworkHeiko Schocher
- add omap24xx driver to new multibus/multiadpater support - adapted all config files, which uses this driver Tested on the am335x based siemens boards rut, dxr2 and pxm2 posted here: http://patchwork.ozlabs.org/patch/263211/ Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Tom Rini <trini@ti.com> Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Thomas Weber <weber@corscience.de> Cc: Tom Rix <Tom.Rix@windriver.com> Cc: Grazvydas Ignotas <notasas@gmail.com> Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Nishanth Menon <nm@ti.com> Cc: Pali Rohár <pali.rohar@gmail.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Michael Jones <michael.jones@matrix-vision.de> Cc: Raphael Assenat <raph@8d.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Stefano Babic <sbabic@denx.de>
2013-11-13i2c: sh_i2c: Update to new CONFIG_SYS_I2C frameworkNobuhiro Iwamatsu
This updates to new I2C framwwork on sh_i2c. And this also updates boards(kzm9g and ecovec) that using sh_i2c. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2013-11-12arm, am335x: update for the siemens boardsSamuel Egli
- dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-12cm_t35: use scf0403 driverNikita Kiryanov
Use scf0403 driver to add scf0403x LCD support for cm-t35 and cm-t3730 boards. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-11-12lcd: add DataImage SCF0403x LCD panel supportNikita Kiryanov
Add SPI-based driver for DataImage SCF0403852GGU04 and SCF0403526GGU20 LCD panels. Cc: Tom Rini <trini@ti.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2013-11-12spi: define SPI_XFER_ONCENikita Kiryanov
The flag combination "SPI_XFER_BEGIN | SPI_XFER_END" is a common use case of spi_xfer, and it can easily cause an already long line (spi_xfer takes 5 parameters) to go over the 80 character limit. define SPI_XFER_ONCE to be a shorter version of the above flag combination. Cc: Tom Rini <trini@ti.com> Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-11-12spi: omap3: add support for more word lengthsNikita Kiryanov
Current implementation only supports 8 bit word lengths, even though omap3 can handle anything between 4 and 32. Update the spi interface to support changing the SPI word length, and implement it in omap3_spi driver to support the full range of possible word lengths. This implementation is backwards compatible by defaulting to the old behavior of 8 bit word lengths. Also, it required a change to the omap3_spi non static I/O functions, but since they are not used anywhere else, no collateral changes are required. Cc: Tom Rini <trini@ti.com> Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-11-11MPC824x: remove obsolete "PN62" boardWolfgang Denk
The MPC824x processors have long reached EOL, and the PN62 board has not seen any board-specific updates for more than a decade. It is now causing build issues. Instead of wasting time on things nobody is interested in any more, we rather drop this board. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Wolfgang Grandegger <wg@grandegger.com> cc: Tom Rini <trini@ti.com>
2013-11-11omap730p2: Remove boardTom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2013-11-11am33xx: Make SoC bootcount driver have its own symbolTom Rini
Some am33xx boards may not use the RTC block for bootcount (as it may not be wired up for the board) and use some other facility. So add another symbol for the bootcount driver for the IP block. Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
2013-11-11cm-t35: use gpio_led driver for status ledIgor Grinberg
Switch to using the generic gpio_led driver instead of the private to cm_t35 board led implementation. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
2013-11-11arm, am33x: make RTC32K OSC enable configurableHeiko Schocher
As http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast states: "Initialize devices only when they are needed within U-Boot" enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is enabled. Enable this in ti_am335x_common.h, so all boards in mainline should work as before. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
2013-11-11Merge branch 'master' of git://git.denx.de/u-boot-mipsTom Rini
2013-11-09Merge branch 'iu-boot/master' into 'u-boot-arm/master'Albert ARIBAUD
Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
2013-11-09malta: define CONFIG_MEMSIZE_IN_BYTESGabor Juhos
The memsize environment variable must contain the memory size in bytes on the Malta board. Otherwise Linux will use wrong memory size which causes a kernel panic. Define CONFIG_MEMSIZE_IN_BYTES in malta.h to avoid that. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Cc: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: store environment in flashPaul Burton
Allow the environment to be stored in the monitor flash of a Malta board. The environment is stored in the final 128KB of the flash, which both leaves the majority of the flash available for U-boot code and also matches the location which YAMON uses. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: enable RTC supportPaul Burton
This is actually required in order for a Linux kernel to boot successfully on a physical Malta board. Without enabling the RTC, a Malta Linux kernel will get stuck in its estimate_frequencies function on boot. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: remove cache size definitionsPaul Burton
These will now be detected at runtime, allowing a single U-boot configuration to function correctly with different bitstreams. Without this you may need to re-configure, re-build and re-flash U-boot to your Malta if you flash a new bitstream with a different cache configuration to your old bitstream. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: enable CONFIG_PCNET_79C973, PCNET_HAS_PROM, CONFIG_CMD_DHCPPaul Burton
This model of the pcnet is used in current Malta boards, at least in the Malta-R rev 3. Enable support for it. The Malta also has the ethernet controller PROM containing its MAC address, so enable support for that in order to read that MAC address. DHCP is a very useful feature to have available for many networks, enable support for it also. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09malta: support for coreFPGA6 boardsPaul Burton
This patch adds support for running on Malta boards using coreFPGA6 core cards, including support for the msc01 system controller used with them. The system controller is detected at runtime allowing one U-boot binary to run on a Malta with either. Due to the PCI I/O base differing between Maltas using gt64120 & msc01 system controllers, the UART setup is modified slightly. A second UART is added so that there is one pointing at the correct address for each system controller. The Malta board then defines its own default_serial_console function to select the correct one at runtime. The incorrect UART will simply not function. Tested on: - A coreFPGA6 Malta running interAptiv and proAptiv bitstreams, both with and without an L2 cache. - QEMU. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09qemu-malta: rename to just "malta"Paul Burton
This is in preparation for adapting this board to function correctly on a physical MIPS Malta board. The board is moved into an "imgtec" vendor directory at the same time in order to ready us for any other boards supported by Imagination in the future. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09pci.h: allow inclusion in assembly sourcePaul Burton
This patch simply #ifdef's out the C-specific parts of pci.h when it is included by an assembly file. This will allow the macros it contains to be used from assembly source as will be done in a followup commit adding support for more modern MIPS Malta boards. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-08Merge branch 'master' of git://www.denx.de/git/u-boot-usbTom Rini
2013-11-08sandbox: convert to common time functionsRob Herring
Convert sandbox to use common time functions. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-08highbank: set AUTOBOOT_KEYED_CTRLC config optionMark Langsdorf
Let highbank users break into the autoboot script with ctrl-c. Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
2013-11-08include: delete include/linux/config.hMasahiro Yamada
Linux Kernel abolished include/linux/config.h long time ago. (around version v2.6.18..v2.6.19) We don't need to provide Linux copatibility any more. This commit deletes include/linux/config.h and fixes source files not to include this. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-08config/sandbox: Add EFI and GPT supportEgbert Eich
Signed-off-by: Egbert Eich <eich@suse.com>
2013-11-08config: Define HAVE_BLOCK_DEVICE when CONFIG_CMD_GPT is setEgbert Eich
Signed-off-by: Egbert Eich <eich@suse.com>
2013-11-08usb, g_dnl: make iSerialNumber board configurableHeiko Schocher
add the possibility to set the iSerialNumber board specific. Default value for iSerialNumber is 0x0. This value can changed board specific through the new function g_dnl_set_serialnumber() which must be called from the board specific function g_dnl_bind_fixup(). Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
2013-11-08usb: ums: add ums exit feature by ctrl+c or by detach usb cablePrzemyslaw Marczak
This patch allows exiting from UMS mode to u-boot prompt by detaching usb cable or by pressing ctrl+c. Add new config: CONFIG_USB_CABLE_CHECK. If defined then board file should provide function: usb_cable_connected() (include/usb.h) that return 1 if cable is connected and 0 otherwise. Changes v2: - add a note to the README Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de>
2013-11-08usb: ums: move ums code from trats to Samsung common directoryPrzemyslaw Marczak
UMS init was implemented in trats board file but mostly it comprises common code. Due to that it has been moved to common/ums.c to avoid code duplication in the future. Changes: - move ums initialization code from trats to common/ums.c - remove unused CONFIG_USB_GADGET_MASS_STORAGE from trats.h Changes v2: - move this patch at the top of code cleanups patches Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Minkyu Kang <mk7.kang@samsung.com>
2013-11-08usb: ums: fix disk capacity miscalculation and code cleanupPrzemyslaw Marczak
This patch prevents: - ums disk capacity miscalculation because of integer overflow Changes v2: - Prevents passing zero size disk capacity to ums gadget driver - Change function ums_get_capacity() to ums_disk_init() and do ums disk initialization before gadget init - Remove unnecessary code from mass storage driver Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de>
2013-11-08usb: ums: code refactoring to improve reusability on other boards.Przemyslaw Marczak
This patch introduces some cleanups to ums code. Changes: ums common: - introduce UMS_START_SECTOR and UMS_NUM_SECTORS as defined in usb_mass_storage.h both default values as 0 if board config doesn't define them common cleanup changes: - change name of struct "ums_board_info" to "ums" - "ums_device" fields are moved to struct ums and "dev_num" is removed - change function name: board_ums_init to ums_init - remove "extern" prefixes from usb_mass_storage.h cmd_usb_mass_storage: - change error() to printf() if need to print info message - change return values to command_ret_t type at ums command code - add command usage string Changes v2: ums common: - always returns number of read/write sectors - coding style clean-up ums gadget: - calculate amount of read/write from device returned value. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marek.vasut@gmail.com>
2013-11-08cosmetic: remove empty lines at the top of fileMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-08Add support for SX151x SPI GPIO ExpandersViktar Palstsiuk
Signed-off-by: Viktar Palstsiuk <viktar.palstsiuk@promwad.com>
2013-11-08EP88x: remove remainders of dead boardMasahiro Yamada
Commit 1b0757e deleted the EP88x entry from boards.cfg file. But it missed to remove include/configs/EP88x.h and board/ep88x/. This commit removes them and adds EP88x to README.scrapyard. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de>
2013-11-07Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-11-06ColdFire: fix some typoes for CF platformjason
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
2013-11-06coldfire: cpu5282: increase malloc space to fix crash on start u-bootJens Scharsig (BuS Elektronik)
The malloc space is to small to boot, the current uboot 2013.10-rcX, This will fix the startup problems by increasing the mallog space to 4MiB. Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
2013-11-05Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-11-04ARM: ATMEL: eb_cpux9k2: fix TEXT_BASE for ramboot targetJens Scharsig (BuS Elektronik)
Since more functions are enabled, the eb_cpux9k2_ram target does not boot. This patch changed the TEXT_BASE, that the code fits between TEXT_BASE and ram end. Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04arm: atmel: get rid of too many ifdefferyBo Shen
Get rid of too many ifdeffery in usb ohci driver Add following two configuration for USB clock selecting - CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock - CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04arm: atmel: at91sam9n12ek: add usb host supportBo Shen
Add usb host support for at91sam9n12ek board. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-11-04ARM: versatile: convert to common timer codeRob Herring
Convert versatile to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04ARM: tegra: convert to common timer codeRob Herring
Convert tegra to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04ARM: socfpga: convert to common timer codeRob Herring
Convert socfpga to use the commmon timer code. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
generated by cgit (git 2.34.1) at 2025-01-01 14:15:00 +0000