| Age | Commit message (Collapse) | Author |
|---|
|
Add CONFIG_SYS_GENERIC_BOARD to use common/board_*.c for koelsch.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Add CONFIG_SYS_GENERIC_BOARD to use common/board_*.c for armadillo800eva.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Lager board has USB ports. This add support of USB controller of rmobile.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Koelsch board has USB ports. This add support of USB controller of rmobile.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
This adds CONFIG_SYS_THUMB_BUILD to config, in order to enable optimization
of thumb.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Because do not need these feature to lager board, this delete it.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
The define of SCIF register was already defined in rcar-base.h.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
This adds CONFIG_SYS_THUMB_BUILD to config, in order to enable optimization
of thumb.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Because do not need these feature to koelsch board, this delete it.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
The define of SCIF register was already defined in rcar-base.h.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
|
|
Added support to load a bitstream image in chunks by reading it in
chunks from SD/MMC.
Command format:
loadfs [dev] [address] [image size] [blocksize] <interface>
[<dev[:part]>] <filename>
Example: fpga loadfs 0 1000000 3dbafc 4000 mmc 0 fpga.bin
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Use new fpga commands for loading partial bitstreams.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Added support to load partial bitstreams.
The partial bitstreams can be loaded using the below commands
Commands:
fpga loadp <dev> <addr> <size>
fpga loadbp <dev> <addr> <size>
The full bit streams can be loaded using the
old commands(fpga load and fpga loadb).
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Clean up partial, full and compressed bitstream handling.
U-Boot supports full bitstream loading and partial
based on detection which is not 100% correct.
Extending fpga_load/fpga_loadbitstream() with one more
argument which stores bitstream type.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Guard the LOADMK functionality with config to provide
an option to enable or disable it.
Enable it for all platforms in mainline which enable CONFIG_CMD_FPGA.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Fix typo in CMD_FPGA command enabling.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Conflicts:
boards.cfg
Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
|
|
The new 768KB u-boot image size requires changes for
SRIO/PCIE boot. These addresses need to be updated to
appropriate locations.
The updated addresses are used to configure the SRIO/PCIE
inbound windows for the boot, and they must be aligned
with the window size based on the SRIO/PCIE modules requirement.
So for the 768KB u-boot image, the inbound window cannot be set
with 0xfff40000 base address and 0xc0000 size, it should be
extended to 1MB size and the base address can be aligned with
the size.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
AFAICT, c=ffe does nothing and was a typo from the original commit
d17123696c6180ac8b74fbd318bf14652623e982 "powerpc/p4080: Add support
for the P4080DS board" and just kept on getting duplicated
in subsequently added board config files.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Edward Swarthout <ed.swarthout@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
In the earlier patches, the SPL/TPL fraamework was introduced.
For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The
SPL was loaded by the code from the internal on-chip ROM. The SPL initializes
the DDR according to the SPD and loads the final uboot image into DDR, then
jump to the DDR to begin execution.
For NAND booting way, the nand SPL has size limitation on some board(e.g.
P1010RDB), it can not be more than 4KB, we can call it "minimal SPL", So the
dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is
loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD
and loads the final uboot image into DDR,then jump to the DDR to begin execution.
This patch enabled SPL/TPL for P1_P2_RDB to support starting from NAND/SD/SPI
flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL.
Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to
execute, so the section .resetvec is no longer needed.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
In case of secure boot from NAND, CSPR and FTIM settings are
same as non-secure NAND boot. CSPR0 is configured as NAND and
CSPR1 is configured as NOR.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
P1020 SoC which has two USB controllers, but only first one is used
on this platform.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Define and use CONTROL_REGISTER_W1C_MASK to make sure that
w1c bits of usb control register do not get reset while
writing any other bit
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
T4160RDB shares the same platform as T4240RDB. T4160 is
a low power version of T4240, with the eight e6500 cores,
two DDR3 controllers, and same peripheral bus interfaces.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Conflicts:
boards.cfg
Trivial conflict, maintainer change plus board addition
|
|
|
|
|
|
|
|
|
|
SPL should load "u-boot-dtb.img" if both CONFIG_OF_CONTROL
and CONFIG_OF_SEPARATE are defined.
Otherwise, "u-boot.img" should be loaded.
Since CONFIG_OF_CONTROL is always undefined for SPL_BUILD,
the undef block should be moved below the conditional definition
of CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
|
|
Before this patch it was only possible to access the default eMMC HW
partition. By partition selection I mean the access to eMMC via the
ext_csd[179] register programming.
It sometimes happens that it is necessary to write to other partitions.
This patch adds extra attribute to "raw" sub type of the dfu_alt_info
environment variable (e.g. boot-mmc.bin raw 0x0 0x200 mmcpart 1;)
It saves the original boot value and restores it after storing the file.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
|
|
15 was too small for variables stored in file on MMC.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Enabled the EXT4 configs.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Moved the USB/SD/MMC common FAT configs separately
to avoid redefinition warnings.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Enable the FAT write capability for SD/MMC write
functionality.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Added configs to support USB host for zynq boards.
Also added a command usbboot to boot from usb.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Extend max kernel image size. Gunzip is checking
this value. If kernel is larger, message below is shown.
Uncompressing Kernel Image ... Error: inflate() returned -5
GUNZIP: uncompress, out-of-mem or overwrite error -
must RESET board to recover
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Call board_init() if SPL is configured with CONFIG_SPL_BOARD_INIT.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
This adds the Gumstix Pepper[1] single-board computer based on the
TI AM335x processor. Schematics are available [2].
[1] https://store.gumstix.com/index.php/products/344/
[2] https://pubs.gumstix.com/boards/PEPPER/
Signed-off-by: Ash Charles <ash@gumstix.com>
[trini: Move 'cdev' in board.c down to under #ifdef's where it's used]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
The commits
commit b7b5f1a16ca66dfdd817e7339f0e263a5b9f2758
Author: Albert ARIBAUD <albert.u.boot@aribaud.net>
da850evm, da850_am18xxevm: convert to CONFIG_SPL_MAX_FOOTPRINT
and
commit e7497891e34efe5cb2b3a3dc7c6c096c012ede28
Author: Albert ARIBAUD <albert.u.boot@aribaud.net>
cam_enc_4xx: convert to CONFIG_SPL_MAX_FOOTPRINT
replaced CONFIG_SPL_MAX_SIZE by CONFIG_SPL_MAX_FOOTPRINT. However,
CONFIG_SPL_MAX_SIZE is used in the Makefile for padding the SPL
when preparing an u-boot.ais image. By removing CONFIG_SPL_MAX_SIZE
said commits broke the ais image of the da850evm and cam_enc_4xx
configurations.
This patch converts the u-boot.ais target to use CONFIG_SPL_PAD_TO
instead of CONFIG_SPL_MAX_SIZE for padding the SPL and adds
a #define CONFIG_SPL_PAD_TO where it is required.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Reported-by: Tom Taylor <ttaylor.tampa@gmail.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
|
|
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Reviewed-by: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
|
|
Fall back to previous dtb used when omap3-beagle-xm-ab.dtb doesn't exist in file system
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@ti.com>
CC: Nishanth Menon <nm@ti.com>
Acked-by: Tom Rini <trini@ti.com>
|
|
As of v3.15-rc3, omap3-beagle-xm-ab.dtb now exists with the usb hub (ehci) enabled.
For older kernels versions, cherry pick from mainline:
ef78f3869c37c480f1d58462a760a40dabc823f4
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@ti.com>
CC: Nishanth Menon <nm@ti.com>
|
|
Add defines required to turn on LDO2 regulator.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
|
