| Age | Commit message (Collapse) | Author |
|---|
|
Flag status register polling is required for micron 512Mb flash
devices onwards, for performing erase/program operations.
Like polling for WIP(Write-In-Progress) bit in read status register,
spi_flash_cmd_wait_ready will poll for PEC(Program-Erase-Control)
bit in flag status register.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Defined bank addr code on CONFIG_SPI_FLASH_BAR macro, to reduce the
size for existing boards which has < 16Mbytes SPI flashes.
It's upto user which has provision to use the bank addr code for
flashes which has > 16Mbytes.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Read the flash bank addr register to get the state of bank in
a perticular flash. and also bank write happens only when there is
a change in bank selection from user.
bank read only valid for flashes which has > 16Mbytes those are
opearted in 3-byte addr mode, each bank occupies 16Mytes.
Suppose if the flash has 64Mbytes size consists of 4 banks like
bank0, bank1, bank2 and bank3.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Bank/Extended addr commands are specific to particular
flash vendor so discover them based on the idocode0.
Assign the discovered bank commands to spi_flash members
so-that the bank read/write will use their specific operations.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
|
|
Discard all .dynsym sections from linker scripts
Remove all __dynsym_start definitions from linker scripts
Remove all __dynsym_start references from the codebase
Note: this touches include/asm-generic/sections.h, which
is not ARM-specific, but actual uses of __dynsym_start
are only in ARM, so this patch can safely go through
the ARM repository.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
|
|
P1023RDB Specification:
-----------------------
Memory subsystem:
512MB DDR3 (Fixed DDR on board)
64MB NOR flash
128MB NAND flash
Ethernet:
eTSEC1: Connected to Atheros AR8035 GETH PHY
eTSEC2: Connected to Atheros AR8035 GETH PHY
PCIe:
Three mini-PCIe slots
USB:
Two USB2.0 Type A ports
I2C:
AT24C08 8K Board EEPROM (8 bit address)
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
There will need the environment in SPL for reasons other than network
support (in particular, hwconfig contains info for how to set up DDR).
Add a new symbol CONFIG_SPL_ENV_SUPPORT to replace CONFIG_SPL_NET_SUPPORT
for environment in common/Makefile.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Relax parameters to give address latching more time to setup.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
When a T4 board boots from SRIO or PCIE, it needs to finish these processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
T4 can support the feature of Boot from SRIO/PCIE, and the macro
"CONFIG_SRIO_PCIE_BOOT_MASTER" will enable the master module of this feature
when building the u-boot image.
You can get some description about this macro in README file, and for more
information about the feature of Boot from SRIO/PCIE, please refer to the
document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
When a b4860qds board boots from SRIO or PCIE, it needs to finish these
processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
B4860QDS can support the feature of Boot from SRIO/PCIE, and the macro
"CONFIG_SRIO_PCIE_BOOT_MASTER" will enable the master module of this feature
when building the u-boot image.
You can get some description about this macro in README file, and for more
information about the feature of Boot from SRIO/PCIE, please refer to the
document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Currently, the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" can enable
the master module of Boot from SRIO and PCIE on a platform. But this
is not a silicon feature, it's just a specific booting mode based on
the SRIO and PCIE interfaces. So it's inappropriate to put the macro
into the file arch/powerpc/include/asm/config_mpc85xx.h.
Change the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" to
"CONFIG_SRIO_PCIE_BOOT_MASTER", remove them from
arch/powerpc/include/asm/config_mpc85xx.h file, and add those macros
in configuration header file of each board which can support the
master module of Boot from SRIO and PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
BSC9131RDB has 1GB DDR.
Out of this, only 880MB is passed on to Linux via bootm_size.
Remaining
-16MB is reserved for PowerPC-DSP shared control area
-128MB is reserved for DSP private area.
Also 256MB, out of this 880MB is required for data communication between
PowerPC and DSP core.
For this bootargs are modified to pass parameter to create 1 hugetlb
page of 256MB via default_hugepagesz, hugepagesz and hugepages
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
BSC9131RDB is a Freescale Reference Design Board for
BSC9131 SoC which is a integrated device that contains
one powerpc e500v2 core and one DSP starcore.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 memory
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
BSC9131RDB supports Sysclk
-66MHz if jumper J16 is close (default state)
-100MHz if jumper J16 is open
Add targets
-BSC9131RDB_NAND_SYSCLK100 : for NAND boot at Sysclk 100MHz
-BSC9131RDB_SPIFLASH_SYSCLK100: for SPI boot at Sysclk 100MHz
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
- Add NAND boot target
- defines constants
- Add spl_minimal.c to initialise DDR
- update TLB, LAW entries as per NAND boot
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
- Add NAND boot target
- defines constants
- Add spl_minimal.c to initialise DDR
- update TLB entries as per NAND boot
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
- defines constants
- Add spl_minimal.c to initialise DDR
- update TLB entries as per NAND boot
- remove nand_spl support for P1010RDB
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
IFC errata A003399 is valid for IFC NOR boot i.e.if no on-board NOR flash or
no NOR boot, do not compile its workaround.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
This patch ensures minimal cooling for the net2big_v2 by automatically
starting the I2C fan (GMT G762) at low speed (2800 RPM).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
|
|
Conflicts:
spl/Makefile
|
|
Detect if we are running on a panda revision A1-A6,
or an ES panda board. This can be done by reading
the level of GPIOs and checking the processor revisions.
This should result in:
Panda 4430:
GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
GPIO171, GPIO101, GPIO182: 1 0 1 => A6
Panda ES:
GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3
Set the board name appropriately for the board revision that
is detected.
Update the findfdt macro to load the a4 device tree binary.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
[trini: %s/CONTROL_PADCONF_CORE/(*ctrl)->control_padconf_core_base/ and
formatting for that]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Update the EXTRA_ENV_SETTING for the dra7xx.
The console needs to be set to ttyO0 and the
findfdt needs to be updated to load the
dra7xx-evm.dtb file.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Correct the console sys prompt to display the correct processor
and the corrent board
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reported-by: Lubomir Popov <lpopov@mm-sol.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
In the omap4, omap5 and am335x common files add a check to ensure that the fdtfile is
defined after the findfdt macro has run. If the file is not defined then warn the user that the
dtb file is not defined.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
|
|
Use a negative value of CONFIG_ENV_OFFSET for all NVIDIA reference boards
that store the U-Boot environment in the 2nd eMMC boot partition. This
makes U-Boot agnostic to the size of the eMMC boot partition, which can
vary depending on which eMMC device was actually stuffed into the board.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Enhance the MMC core to calculate the size of each MMC partition, and
update mmc->capacity whenever a partition is selected. This causes:
mmc dev 0 1 ; mmcinfo
... to report the size of the currently selected partition, rather than
always reporting the size of the user partition.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
The commit d196bd8 (env_mmc: add support for redundant environment)
introduce the following compile error when enable redundant
environment support with MMC
---8<---
env_mmc.c:149: error: 'env_t' has no member named 'flags'
env_mmc.c:248: error: 'env_t' has no member named 'flags'
env_mmc.c:248: error: 'env_t' has no member named 'flags'
env_mmc.c:250: error: 'env_t' has no member named 'flags'
env_mmc.c:250: error: 'env_t' has no member named 'flags'
env_mmc.c:252: error: 'env_t' has no member named 'flags'
env_mmc.c:252: error: 'env_t' has no member named 'flags'
env_mmc.c:254: error: 'env_t' has no member named 'flags'
env_mmc.c:254: error: 'env_t' has no member named 'flags'
env_mmc.c:267: error: 'env_t' has no member named 'flags'
make[1]: *** [env_mmc.o] Error 1
--->8---
Add this patch to fix it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
|
|
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR
Conflicts:
arch/arm/include/asm/arch-omap5/omap.h
Signed-off-by: Tom Rini <trini@ti.com>
|
|
This patch adds APIs to access(open / close) and to resize boot partiton of EMMC.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch enables and initialises DWMMC for SMDK5250.
Supports both FDT and non-FDT. This patch creates a new file
'exynos5-dt.c' meant for FDT support.
exynos5-dt.c: This file shall contain all code which supports FDT.
Any addition of FDT support for any module needs to be
added in this file.
smdk5250.c: This file shall contain the code which supports non-FDT.
version. Any addition of non-FDT support for any module
needs to be added in this file.
May be, the file smdk5250.c can be removed in near future
when non-FDT is not required.
The Makefile is updated to compile only one of the files
exynos5-dt.c / smdk5250.c based on FDT configuration.
NOTE:
Please note that all additions corresponding to FDT need to be added into the
file exynos5-dt.c.
At same time if non-FDT support is required then add the corresponding
updations into smdk5250.c.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch adds FDT support for DWMMC, by reading the DWMMC node data
from the device tree and initialising DWMMC channels as per data
obtained from the node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Add required compatible information for DWMMC driver.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Signed-off-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
|
|
LP-8x4x is a programmable automation controller by ICP DAS. It is
shipped with outdated U-Boot v1.3.0
This patch adds enough supports to boot the board:
- 128M of 128M SDRAM
- 32M of 48M NOR Flash memory
- 1 of 4 Serial consoles (PXA FFUART)
- 2 of 2 Ethernet controllers (DM9000)
Signed-off-by: Sergey Yanovich <ynvich@gmail.com>
Series-to: u-boot
Series-cc: marex
|
|
This patch adds support to both Faraday FUSBH200 and FOTG210,
the differences between Faraday EHCI and standard EHCI are
listed bellow:
1. The PORTSC starts at 0x30 instead of 0x44.
2. The CONFIGFLAG(0x40) is not only un-implemented, and
also has its address space removed.
3. Faraday EHCI is a TDI design, but it doesn't
compatible with the general TDI implementation
found at both U-Boot and Linux.
4. The ISOC descriptors differ from standard EHCI in
several ways. But since U-boot doesn't support ISOC,
we don't have to worry about that.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
|
|
Use unaligned access to fetch wMaxPacketSize in usb_endpoint_maxp()
api.
In its absence we see following data abort message:
==============================================================
data abort
MAYBE you should read doc/README.arm-unaligned-accesses
pc : [<bf794e24>] lr : [<bf794e1c>]
sp : bf37c7b0 ip : 0000002f fp : 00000000
r10: 00000000 r9 : 00000002 r8 : bf37fecc
r7 : 00000001 r6 : bf7d8931 r5 : bf7d891c r4 : bf7d8800
r3 : bf7d65b0 r2 : 00000002 r1 : bf7d65b4 r0 : 00000027
Flags: nZCv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
resetting ...
==============================================================
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Marek Vasut <marex@denx.de>
|
|
|
|
The flash_info_t->start[] field is limited in size by CONFIG_SYS_MAX_FLASH_SECT
macro, which is set to 19 for this board in the board config file. If we inspect
the board/ppmc7xx/flash.c closely, especially the flash_get_size() function, we
can notice the "switch ((long)flashtest)" at around line 80 having a few results
which will set flash_info_t->sector_count to value higher than 19, for example
"case AMD_ID_LV640U" will set it to 128. Notice that right underneath, iteration
over flash_info_t->start[] happens and the upper bound for the interation is
flash_info_t->sector_count. Now if the sector_count is 128 as it is for the
AMD_ID_LV640U case, but the CONFIG_SYS_MAX_FLASH_SECT limiting the start[] is
only 19, an access past the start[] array much happen. Moreover, during this
iteration, the field is written to, so memory corruption is inevitable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Richard Danter <richard.danter@windriver.com>
|
|
C99's strict aliasing rules are insane to use in low-level code such as a
bootloader, but as Wolfgang has rejected -fno-strict-aliasing in the
past, add a union so that 16-bit accesses can be performed.
Compile-tested only.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
|
|
Move pinmux configurations for the DA830 SoCs from board file
to the arch tree so that it can be used for all da830 based devices.
Also, avoids duplicate pinmuxing in case of NAND.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
|
|
The omap2420H4 was the only mainline omap24xx board. Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time. Remove this board as there's not been interest in
it in U-Boot for quite a long time.
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Add MMC support for da830 boards in order to perform
mmc operations(read,write and erase).
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
|
|
Add some useful functions, and the corresponding definitions.
Add support for powering on the dra7xx_evm SD/MMC LDO
(courtesy Lokesh Vutla <lokeshvutla@ti.com>).
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
