1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
|
/*
* armboot - Startup Code for ARM926EJS CPU-core
*
* Copyright (c) 2003 Texas Instruments
*
* ----- Adapted for OMAP1610 OMAP730 from ARM925t code ------
*
* Copyright (c) 2001 Marius Groger <mag@sysgo.de>
* Copyright (c) 2002 Alex Zupke <azu@sysgo.de>
* Copyright (c) 2002 Gary Jennejohn <garyj@denx.de>
* Copyright (c) 2003 Richard Woodruff <r-woodruff2@ti.com>
* Copyright (c) 2003 Kshitij <kshitij@ti.com>
* Copyright (c) 2010 Albert Aribaud <albert.u.boot@aribaud.net>
*
* Change to support call back into iMX28 bootrom
* Copyright (c) 2011 Marek Vasut <marek.vasut@gmail.com>
* on behalf of DENX Software Engineering GmbH
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <asm-offsets.h>
#include <config.h>
#include <common.h>
#include <version.h>
/*
*************************************************************************
*
* Jump vector table as in table 3.1 in [1]
*
*************************************************************************
*/
.globl _start
_start:
b reset
b undefined_instruction
b software_interrupt
b prefetch_abort
b data_abort
b not_used
b irq
b fiq
/*
* Vector table, located at address 0x20.
* This table allows the code running AFTER SPL, the U-Boot, to install it's
* interrupt handlers here. The problem is that the U-Boot is loaded into RAM,
* including it's interrupt vectoring table and the table at 0x0 is still the
* SPLs. So if interrupt happens in U-Boot, the SPLs interrupt vectoring table
* is still used.
*/
_vt_reset:
.word _reset
_vt_undefined_instruction:
.word _hang
_vt_software_interrupt:
.word _hang
_vt_prefetch_abort:
.word _hang
_vt_data_abort:
.word _hang
_vt_not_used:
.word _reset
_vt_irq:
.word _hang
_vt_fiq:
.word _hang
reset:
ldr pc, _vt_reset
undefined_instruction:
ldr pc, _vt_undefined_instruction
software_interrupt:
ldr pc, _vt_software_interrupt
prefetch_abort:
ldr pc, _vt_prefetch_abort
data_abort:
ldr pc, _vt_data_abort
not_used:
ldr pc, _vt_not_used
irq:
ldr pc, _vt_irq
fiq:
ldr pc, _vt_fiq
.balignl 16,0xdeadbeef
/*
*************************************************************************
*
* Startup Code (reset vector)
*
* do important init only if we don't start from memory!
* setup Memory and board specific bits prior to relocation.
* relocate armboot to ram
* setup stack
*
*************************************************************************
*/
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
IRQ_STACK_START:
.word 0x0badc0de
/* IRQ stack memory (calculated at run-time) */
.globl FIQ_STACK_START
FIQ_STACK_START:
.word 0x0badc0de
#endif
/* IRQ stack memory (calculated at run-time) + 8 bytes */
.globl IRQ_STACK_START_IN
IRQ_STACK_START_IN:
.word 0x0badc0de
/*
* the actual reset code
*/
_reset:
/*
* If the CPU is configured in "Wait JTAG connection mode", the stack
* pointer is not configured and is zero. This will cause crash when
* trying to push data onto stack right below here. Load the SP and make
* it point to the end of OCRAM if the SP is zero.
*/
cmp sp, #0x00000000
ldreq sp, =CONFIG_SYS_INIT_SP_ADDR
/*
* Store all registers on old stack pointer, this will allow us later to
* return to the BootROM and let the BootROM load U-Boot into RAM.
*
* WARNING: Register r0 and r1 are used by the BootROM to pass data
* to the called code. Register r0 will contain arbitrary
* data that are set in the BootStream. In case this code
* was started with CALL instruction, register r1 will contain
* pointer to the return value this function can then set.
* The code below MUST NOT CHANGE register r0 and r1 !
*/
push {r0-r12,r14}
/* Save control register c1 */
mrc p15, 0, r2, c1, c0, 0
push {r2}
/* Set the cpu to SVC32 mode and store old CPSR register content. */
mrs r2, cpsr
push {r2}
bic r2, r2, #0x1f
orr r2, r2, #0xd3
msr cpsr, r2
bl board_init_ll
/* Restore BootROM's CPU mode (especially FIQ). */
pop {r2}
msr cpsr,r2
/*
* Restore c1 register. Especially set exception vector location
* back to BootROM space which is required by bootrom for USB boot.
*/
pop {r2}
mcr p15, 0, r2, c1, c0, 0
pop {r0-r12,r14}
/*
* In case this code was started by the CALL instruction, the register
* r0 is examined by the BootROM after this code returns. The value in
* r0 must be set to 0 to indicate successful return.
*/
mov r0, #0
bx lr
_hang:
1:
bl 1b /* hang and never return */
|
