1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
|
/*
* Copyright (C) 2012-2014 Panasonic Corporation
* Author: Masahiro Yamada <yamada.m@jp.panasonic.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <config.h>
#include <linux/linkage.h>
#include <asm/system.h>
#include <asm/arch/led.h>
#include <asm/arch/arm-mpcore.h>
#include <asm/arch/sbc-regs.h>
ENTRY(lowlevel_init)
mov r8, lr @ persevere link reg across call
/*
* The UniPhier Boot ROM loads SPL code to the L2 cache.
* But CPUs can only do instruction fetch now because start.S has
* cleared C and M bits.
* First we need to turn on MMU and Dcache again to get back
* data access to L2.
*/
mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Contrl Register)
orr r0, r0, #(CR_C | CR_M) @ enable MMU and Dcache
mcr p15, 0, r0, c1, c0, 0
#ifdef CONFIG_DEBUG_LL
bl setup_lowlevel_debug
#endif
/*
* Now we are using the page table embedded in the Boot ROM.
* It is not handy since it is not a straight mapped table for sLD3.
* What we need to do next is to switch over to the page table in SPL.
*/
ldr r3, =init_page_table @ page table must be 16KB aligned
/* Disable MMU and Dcache before switching Page Table */
mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Contrl Register)
bic r0, r0, #(CR_C | CR_M) @ disable MMU and Dcache
mcr p15, 0, r0, c1, c0, 0
bl enable_mmu
#ifdef CONFIG_UNIPHIER_SMP
/*
* ACTLR (Auxiliary Control Register) for Cortex-A9
* bit[9] Parity on
* bit[8] Alloc in one way
* bit[7] EXCL (Exclusive cache bit)
* bit[6] SMP
* bit[3] Write full line of zeros mode
* bit[2] L1 Prefetch enable
* bit[1] L2 prefetch enable
* bit[0] FW (Cache and TLB maintenance broadcast)
*/
mrc p15, 0, r0, c1, c0, 1 @ ACTLR (Auxiliary Control Register)
orr r0, r0, #0x41 @ enable SMP, FW bit
mcr p15, 0, r0, c1, c0, 1
/* branch by CPU ID */
mrc p15, 0, r0, c0, c0, 5 @ MPIDR (Multiprocessor Affinity Register)
and r0, r0, #0x3
cmp r0, #0x0
beq primary_cpu
ldr r1, =ROM_BOOT_ROMRSV2
mov r0, #0
str r0, [r1]
0: wfe
ldr r0, [r1]
cmp r0, #0
beq 0b
bx r0 @ r0: entry point of U-Boot main for the secondary CPU
primary_cpu:
ldr r1, =ROM_BOOT_ROMRSV2
ldr r0, =_start @ entry for the secondary CPU
str r0, [r1]
ldr r0, [r1] @ make sure str is complete before sev
sev @ kick the sedoncary CPU
mrc p15, 4, r1, c15, c0, 0 @ Configuration Base Address Register
bfc r1, #0, #13 @ clear bit 12-0
mov r0, #-1
str r0, [r1, #SCU_INV_ALL] @ SCU Invalidate All Register
mov r0, #1 @ SCU enable
str r0, [r1, #SCU_CTRL] @ SCU Control Register
#endif
bl setup_init_ram @ RAM area for temporary stack pointer
mov lr, r8 @ restore link
mov pc, lr @ back to my caller
ENDPROC(lowlevel_init)
ENTRY(enable_mmu)
mrc p15, 0, r0, c2, c0, 2 @ TTBCR (Translation Table Base Control Register)
bic r0, r0, #0x37
orr r0, r0, #0x20 @ disable TTBR1
mcr p15, 0, r0, c2, c0, 2
orr r0, r3, #0x8 @ Outer Cacheability for table walks: WBWA
mcr p15, 0, r0, c2, c0, 0 @ TTBR0
mov r0, #0
mcr p15, 0, r0, c8, c7, 0 @ invalidate TLBs
mov r0, #-1 @ manager for all domains (No permission check)
mcr p15, 0, r0, c3, c0, 0 @ DACR (Domain Access Control Register)
dsb
isb
/*
* MMU on:
* TLBs was already invalidated in "../start.S"
* So, we don't need to invalidate it here.
*/
mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Contrl Register)
orr r0, r0, #(CR_C | CR_M) @ MMU and Dcache enable
mcr p15, 0, r0, c1, c0, 0
mov pc, lr
ENDPROC(enable_mmu)
#include <asm/arch/ssc-regs.h>
#define BOOT_RAM_SIZE (SSC_WAY_SIZE)
#define BOOT_WAY_BITS (0x00000100) /* way 8 */
ENTRY(setup_init_ram)
/*
* Touch to zero for the boot way
*/
0:
/*
* set SSCOQM, SSCOQAD, SSCOQSZ, SSCOQWN in this order
*/
ldr r0, = 0x00408006 @ touch to zero with address range
ldr r1, = SSCOQM
str r0, [r1]
ldr r0, = (CONFIG_SYS_INIT_SP_ADDR - BOOT_RAM_SIZE) @ base address
ldr r1, = SSCOQAD
str r0, [r1]
ldr r0, = BOOT_RAM_SIZE
ldr r1, = SSCOQSZ
str r0, [r1]
ldr r0, = BOOT_WAY_BITS
ldr r1, = SSCOQWN
str r0, [r1]
ldr r1, = SSCOPPQSEF
ldr r0, [r1]
cmp r0, #0 @ check if the command is successfully set
bne 0b @ try again if an error occurres
ldr r1, = SSCOLPQS
1:
ldr r0, [r1]
cmp r0, #0x4
bne 1b @ wait until the operation is completed
str r0, [r1] @ clear the complete notification flag
mov pc, lr
ENDPROC(setup_init_ram)
|
