blob: beedc125b63e8b2e8b2f36aa611c35ed96344ce2 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
|
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2011
* Marvell Semiconductor <www.marvell.com>
* Written-by: Lei Wen <leiwen@marvell.com>
*/
/*
* This file should be included in board config header file.
*
* It supports common definitions for Kirkwood platform
*/
#ifndef _KW_CONFIG_H
#define _KW_CONFIG_H
#if defined (CONFIG_KW88F6281)
#include <asm/arch/kw88f6281.h>
#elif defined (CONFIG_KW88F6192)
#include <asm/arch/kw88f6192.h>
#else
#error "SOC Name not defined"
#endif /* CONFIG_KW88F6281 */
#include <asm/arch/soc.h>
#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */
/*
* By default kwbimage.cfg from board specific folder is used
* If for some board, different configuration file need to be used,
* CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
*/
#ifndef CONFIG_SYS_KWD_CONFIG
#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
#endif /* CONFIG_SYS_KWD_CONFIG */
/* Kirkwood has 2k of Security SRAM, use it for SP */
#define CONFIG_SYS_INIT_SP_ADDR 0xC8012000
#define CONFIG_I2C_MVTWSI_BASE0 KW_TWSI_BASE
#define MV_UART_CONSOLE_BASE KW_UART0_BASE
#define MV_SATA_BASE KW_SATA_BASE
#define MV_SATA_PORT0_OFFSET KW_SATA_PORT0_OFFSET
#define MV_SATA_PORT1_OFFSET KW_SATA_PORT1_OFFSET
/*
* NAND configuration
*/
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_KIRKWOOD
#define CONFIG_SYS_NAND_BASE 0xD8000000 /* MV_DEFADR_NANDF */
#define NAND_ALLOW_ERASE_ALL 1
#endif
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
#define CONFIG_NETCONSOLE /* include NetConsole support */
#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
#endif /* CONFIG_CMD_NET */
/*
* USB/EHCI
*/
#ifdef CONFIG_CMD_USB
#define CONFIG_EHCI_IS_TDI
#endif /* CONFIG_CMD_USB */
/*
* IDE Support on SATA ports
*/
#ifdef CONFIG_IDE
#define __io
#define CONFIG_IDE_PREINIT
#define CONFIG_MVSATA_IDE_USE_PORT1
/* Needs byte-swapping for ATA data register */
#define CONFIG_IDE_SWAP_IO
/* Data, registers and alternate blocks are at the same offset */
#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100)
#define CONFIG_SYS_ATA_REG_OFFSET (0x0100)
#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100)
/* Each 8-bit ATA register is aligned to a 4-bytes address */
#define CONFIG_SYS_ATA_STRIDE 4
/* Controller supports 48-bits LBA addressing */
#define CONFIG_LBA48
/* CONFIG_IDE requires some #defines for ATA registers */
#define CONFIG_SYS_IDE_MAXBUS 2
#define CONFIG_SYS_IDE_MAXDEVICE 2
/* ATA registers base is at SATA controller base */
#define CONFIG_SYS_ATA_BASE_ADDR MV_SATA_BASE
#endif /* CONFIG_IDE */
/*
* I2C related stuff
*/
#if defined(CONFIG_CMD_I2C) && !defined(CONFIG_DM_I2C)
#ifndef CONFIG_SYS_I2C_SOFT
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MVTWSI
#endif
#define CONFIG_SYS_I2C_SLAVE 0x0
#define CONFIG_SYS_I2C_SPEED 100000
#endif
/* Use common timer */
#define CONFIG_SYS_TIMER_COUNTS_DOWN
#define CONFIG_SYS_TIMER_COUNTER (MVEBU_TIMER_BASE + 0x14)
#define CONFIG_SYS_TIMER_RATE CONFIG_SYS_TCLK
#endif /* _KW_CONFIG_H */
|
