1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
|
/*
* Copyright (C) 2015, Bin Meng <bmeng.cn@gmail.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <pci.h>
#include <pci_rom.h>
#include <asm/pci.h>
#include <asm/arch/device.h>
#include <asm/arch/qemu.h>
DECLARE_GLOBAL_DATA_PTR;
static bool i440fx;
void board_pci_setup_hose(struct pci_controller *hose)
{
hose->first_busno = 0;
hose->last_busno = 0;
/* PCI memory space */
pci_set_region(hose->regions + 0,
CONFIG_PCI_MEM_BUS,
CONFIG_PCI_MEM_PHYS,
CONFIG_PCI_MEM_SIZE,
PCI_REGION_MEM);
/* PCI IO space */
pci_set_region(hose->regions + 1,
CONFIG_PCI_IO_BUS,
CONFIG_PCI_IO_PHYS,
CONFIG_PCI_IO_SIZE,
PCI_REGION_IO);
pci_set_region(hose->regions + 2,
CONFIG_PCI_PREF_BUS,
CONFIG_PCI_PREF_PHYS,
CONFIG_PCI_PREF_SIZE,
PCI_REGION_PREFETCH);
pci_set_region(hose->regions + 3,
0,
0,
gd->ram_size,
PCI_REGION_MEM | PCI_REGION_SYS_MEMORY);
hose->region_count = 4;
}
int board_pci_post_scan(struct pci_controller *hose)
{
int ret = 0;
u16 device, xbcs;
int pam, i;
pci_dev_t vga;
ulong start;
/*
* i440FX and Q35 chipset have different PAM register offset, but with
* the same bitfield layout. Here we determine the offset based on its
* PCI device ID.
*/
device = x86_pci_read_config16(PCI_BDF(0, 0, 0), PCI_DEVICE_ID);
i440fx = (device == PCI_DEVICE_ID_INTEL_82441);
pam = i440fx ? I440FX_PAM : Q35_PAM;
/*
* Initialize Programmable Attribute Map (PAM) Registers
*
* Configure legacy segments C/D/E/F to system RAM
*/
for (i = 0; i < PAM_NUM; i++)
x86_pci_write_config8(PCI_BDF(0, 0, 0), pam + i, PAM_RW);
if (i440fx) {
/*
* Enable legacy IDE I/O ports decode
*
* Note: QEMU always decode legacy IDE I/O port on PIIX chipset.
* However Linux ata_piix driver does sanity check on these two
* registers to see whether legacy ports decode is turned on.
* This is to make Linux ata_piix driver happy.
*/
x86_pci_write_config16(PIIX_IDE, IDE0_TIM, IDE_DECODE_EN);
x86_pci_write_config16(PIIX_IDE, IDE1_TIM, IDE_DECODE_EN);
/* Enable I/O APIC */
xbcs = x86_pci_read_config16(PIIX_ISA, XBCS);
xbcs |= APIC_EN;
x86_pci_write_config16(PIIX_ISA, XBCS, xbcs);
} else {
/* Configure PCIe ECAM base address */
x86_pci_write_config32(PCI_BDF(0, 0, 0), PCIEX_BAR,
CONFIG_PCIE_ECAM_BASE | BAR_EN);
}
/*
* QEMU emulated graphic card shows in the PCI configuration space with
* PCI vendor id and device id as an artificial pair 0x1234:0x1111.
* It is on PCI bus 0, function 0, but device number is not consistent
* for the two x86 targets it supports. For i440FX and PIIX chipset
* board, it shows as device 2, while for Q35 and ICH9 chipset board,
* it shows as device 1.
*/
vga = i440fx ? I440FX_VGA : Q35_VGA;
start = get_timer(0);
ret = pci_run_vga_bios(vga, NULL, PCI_ROM_USE_NATIVE);
debug("BIOS ran in %lums\n", get_timer(start));
return ret;
}
#ifdef CONFIG_GENERATE_MP_TABLE
int mp_determine_pci_dstirq(int bus, int dev, int func, int pirq)
{
u8 irq;
if (i440fx) {
/*
* Not like most x86 platforms, the PIRQ[A-D] on PIIX3 are not
* connected to I/O APIC INTPIN#16-19. Instead they are routed
* to an irq number controled by the PIRQ routing register.
*/
irq = x86_pci_read_config8(PCI_BDF(bus, dev, func),
PCI_INTERRUPT_LINE);
} else {
/*
* ICH9's PIRQ[A-H] are not consecutive numbers from 0 to 7.
* PIRQ[A-D] still maps to [0-3] but PIRQ[E-H] maps to [8-11].
*/
irq = pirq < 8 ? pirq + 16 : pirq + 12;
}
return irq;
}
#endif
|
