1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
|
/*
* Copyright (C) 2015, Bin Meng <bmeng.cn@gmail.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/irq.h>
#include <asm/pci.h>
#include <asm/post.h>
#include <asm/processor.h>
#include <asm/arch/device.h>
#include <asm/arch/qemu.h>
static bool i440fx;
static void qemu_chipset_init(void)
{
u16 device, xbcs;
int pam, i;
/*
* i440FX and Q35 chipset have different PAM register offset, but with
* the same bitfield layout. Here we determine the offset based on its
* PCI device ID.
*/
device = x86_pci_read_config16(PCI_BDF(0, 0, 0), PCI_DEVICE_ID);
i440fx = (device == PCI_DEVICE_ID_INTEL_82441);
pam = i440fx ? I440FX_PAM : Q35_PAM;
/*
* Initialize Programmable Attribute Map (PAM) Registers
*
* Configure legacy segments C/D/E/F to system RAM
*/
for (i = 0; i < PAM_NUM; i++)
x86_pci_write_config8(PCI_BDF(0, 0, 0), pam + i, PAM_RW);
if (i440fx) {
/*
* Enable legacy IDE I/O ports decode
*
* Note: QEMU always decode legacy IDE I/O port on PIIX chipset.
* However Linux ata_piix driver does sanity check on these two
* registers to see whether legacy ports decode is turned on.
* This is to make Linux ata_piix driver happy.
*/
x86_pci_write_config16(PIIX_IDE, IDE0_TIM, IDE_DECODE_EN);
x86_pci_write_config16(PIIX_IDE, IDE1_TIM, IDE_DECODE_EN);
/* Enable I/O APIC */
xbcs = x86_pci_read_config16(PIIX_ISA, XBCS);
xbcs |= APIC_EN;
x86_pci_write_config16(PIIX_ISA, XBCS, xbcs);
} else {
/* Configure PCIe ECAM base address */
x86_pci_write_config32(PCI_BDF(0, 0, 0), PCIEX_BAR,
CONFIG_PCIE_ECAM_BASE | BAR_EN);
}
}
int arch_cpu_init(void)
{
int ret;
post_code(POST_CPU_INIT);
#ifdef CONFIG_SYS_X86_TSC_TIMER
timer_set_base(rdtsc());
#endif
ret = x86_cpu_init_f();
if (ret)
return ret;
return 0;
}
#ifndef CONFIG_EFI_STUB
int print_cpuinfo(void)
{
post_code(POST_CPU_INFO);
return default_print_cpuinfo();
}
#endif
void reset_cpu(ulong addr)
{
/* cold reset */
x86_full_reset();
}
int arch_early_init_r(void)
{
qemu_chipset_init();
return 0;
}
int arch_misc_init(void)
{
return pirq_init();
}
#ifdef CONFIG_GENERATE_MP_TABLE
int mp_determine_pci_dstirq(int bus, int dev, int func, int pirq)
{
u8 irq;
if (i440fx) {
/*
* Not like most x86 platforms, the PIRQ[A-D] on PIIX3 are not
* connected to I/O APIC INTPIN#16-19. Instead they are routed
* to an irq number controled by the PIRQ routing register.
*/
irq = x86_pci_read_config8(PCI_BDF(bus, dev, func),
PCI_INTERRUPT_LINE);
} else {
/*
* ICH9's PIRQ[A-H] are not consecutive numbers from 0 to 7.
* PIRQ[A-D] still maps to [0-3] but PIRQ[E-H] maps to [8-11].
*/
irq = pirq < 8 ? pirq + 16 : pirq + 12;
}
return irq;
}
#endif
|
