summaryrefslogtreecommitdiff
path: root/board/Marvell/dreamplug/dreamplug.c
blob: 887dd1ed74d4da827f0901e25967a0a51fab0994 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
// SPDX-License-Identifier: GPL-2.0+
/*
 * (C) Copyright 2011
 * Jason Cooper <u-boot@lakedaemon.net>
 *
 * Based on work by:
 * Marvell Semiconductor <www.marvell.com>
 * Written-by: Siddarth Gore <gores@marvell.com>
 */

#include <common.h>
#include <miiphy.h>
#include <net.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#include <asm/arch/mpp.h>
#include "dreamplug.h"

DECLARE_GLOBAL_DATA_PTR;

int board_early_init_f(void)
{
	/*
	 * default gpio configuration
	 * There are maximum 64 gpios controlled through 2 sets of registers
	 * the  below configuration configures mainly initial LED status
	 */
	mvebu_config_gpio(DREAMPLUG_OE_VAL_LOW,
			  DREAMPLUG_OE_VAL_HIGH,
			  DREAMPLUG_OE_LOW, DREAMPLUG_OE_HIGH);

	/* Multi-Purpose Pins Functionality configuration */
	static const u32 kwmpp_config[] = {
		MPP0_SPI_SCn,		/* SPI Flash */
		MPP1_SPI_MOSI,
		MPP2_SPI_SCK,
		MPP3_SPI_MISO,
		MPP4_NF_IO6,
		MPP5_NF_IO7,
		MPP6_SYSRST_OUTn,
		MPP7_GPO,
		MPP8_TW_SDA,
		MPP9_TW_SCK,
		MPP10_UART0_TXD,	/* Serial */
		MPP11_UART0_RXD,
		MPP12_SD_CLK,		/* SDIO Slot */
		MPP13_SD_CMD,
		MPP14_SD_D0,
		MPP15_SD_D1,
		MPP16_SD_D2,
		MPP17_SD_D3,
		MPP18_NF_IO0,
		MPP19_NF_IO1,
		MPP20_GE1_0,		/* Gigabit Ethernet */
		MPP21_GE1_1,
		MPP22_GE1_2,
		MPP23_GE1_3,
		MPP24_GE1_4,
		MPP25_GE1_5,
		MPP26_GE1_6,
		MPP27_GE1_7,
		MPP28_GE1_8,
		MPP29_GE1_9,
		MPP30_GE1_10,
		MPP31_GE1_11,
		MPP32_GE1_12,
		MPP33_GE1_13,
		MPP34_GE1_14,
		MPP35_GE1_15,
		MPP36_GPIO,		/* 7 external GPIO pins (36 - 45) */
		MPP37_GPIO,
		MPP38_GPIO,
		MPP39_GPIO,
		MPP40_TDM_SPI_SCK,
		MPP41_TDM_SPI_MISO,
		MPP42_TDM_SPI_MOSI,
		MPP43_GPIO,
		MPP44_GPIO,
		MPP45_GPIO,
		MPP46_GPIO,
		MPP47_GPIO,		/* Bluetooth LED */
		MPP48_GPIO,		/* Wifi LED */
		MPP49_GPIO,		/* Wifi AP LED */
		0
	};
	kirkwood_mpp_conf(kwmpp_config, NULL);
	return 0;
}

int board_init(void)
{
	/* adress of boot parameters */
	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;

	return 0;
}

#ifdef CONFIG_RESET_PHY_R
void mv_phy_88e1116_init(char *name)
{
	u16 reg;
	u16 devadr;

	if (miiphy_set_current_dev(name))
		return;

	/* command to read PHY dev address */
	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
		printf("Err..%s could not read PHY dev address\n",
			__func__);
		return;
	}

	/*
	 * Enable RGMII delay on Tx and Rx for CPU port
	 * Ref: sec 4.7.2 of chip datasheet
	 */
	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
	miiphy_read(name, devadr, MV88E1116_MAC_CTRL2_REG, &reg);
	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
	miiphy_write(name, devadr, MV88E1116_MAC_CTRL2_REG, reg);
	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);

	/* reset the phy */
	miiphy_reset(name, devadr);

	printf("88E1116 Initialized on %s\n", name);
}

void reset_phy(void)
{
	/* configure and initialize both PHY's */
	mv_phy_88e1116_init("egiga0");
	mv_phy_88e1116_init("egiga1");
}
#endif /* CONFIG_RESET_PHY_R */