1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
|
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2012
* Corscience GmbH & Co. KG, <www.corscience.de>
* Thomas Weber <weber@corscience.de>
* Sunil Kumar <sunilsaini05@gmail.com>
* Shashi Ranjan <shashiranjanmca05@gmail.com>
*
* Derived from Devkit8000 code by
* Frederik Kriewitz <frederik@kriewitz.eu>
*/
#include <common.h>
#include <init.h>
#include <malloc.h>
#include <twl4030.h>
#include <status_led.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/mux.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/mem.h>
#include "tricorder.h"
#include "tricorder-eeprom.h"
DECLARE_GLOBAL_DATA_PTR;
/*
* Routine: board_init
* Description: Early hardware init.
*/
int board_init(void)
{
gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
/* boot param addr */
gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
return 0;
}
/**
* get_eeprom - read the eeprom
*
* @eeprom - pointer to a eeprom struct to fill
*
* This function will panic() on wrong EEPROM content
*/
static void get_eeprom(struct tricorder_eeprom *eeprom)
{
int ret;
if (!eeprom)
panic("No eeprom given!\n");
ret = gpio_request(7, "BMS");
if (ret)
panic("gpio: requesting BMS pin failed\n");
ret = gpio_direction_input(7);
if (ret)
panic("gpio: set BMS as input failed\n");
ret = gpio_get_value(7);
if (ret < 0)
panic("gpio: get BMS pin state failed\n");
gpio_free(7);
if (ret == 0) {
/* BMS is _not_ set, do the EEPROM check */
ret = tricorder_get_eeprom(0x51, eeprom);
if (!ret) {
if (strncmp(eeprom->board_name, "CS10411", 7) != 0)
panic("Wrong board name '%.*s'\n",
sizeof(eeprom->board_name),
eeprom->board_name);
if (eeprom->board_version[0] < 'D')
panic("Wrong board version '%.*s'\n",
sizeof(eeprom->board_version),
eeprom->board_version);
} else {
panic("Could not get board revision\n");
}
} else {
memset(eeprom, 0, TRICORDER_EEPROM_SIZE);
}
}
/**
* print_hwversion - print out a HW version string
*
* @eeprom - pointer to the eeprom
*/
static void print_hwversion(struct tricorder_eeprom *eeprom)
{
size_t len;
if (!eeprom)
panic("No eeprom given!");
printf("Board %.*s:%.*s serial %.*s",
sizeof(eeprom->board_name), eeprom->board_name,
sizeof(eeprom->board_version), eeprom->board_version,
sizeof(eeprom->board_serial), eeprom->board_serial);
len = strnlen(eeprom->interface_version,
sizeof(eeprom->interface_version));
if (len > 0)
printf(" HW interface version %.*s",
sizeof(eeprom->interface_version),
eeprom->interface_version);
puts("\n");
}
/*
* Routine: misc_init_r
* Description: Configure board specific parts
*/
int misc_init_r(void)
{
struct tricorder_eeprom eeprom;
get_eeprom(&eeprom);
print_hwversion(&eeprom);
twl4030_power_init();
status_led_set(0, CONFIG_LED_STATUS_ON);
status_led_set(1, CONFIG_LED_STATUS_ON);
status_led_set(2, CONFIG_LED_STATUS_ON);
omap_die_id_display();
return 0;
}
/*
* Routine: set_muxconf_regs
* Description: Setting up the configuration Mux registers specific to the
* hardware. Many pins need to be moved from protect to primary
* mode.
*/
void set_muxconf_regs(void)
{
MUX_TRICORDER();
}
#if defined(CONFIG_MMC)
int board_mmc_init(bd_t *bis)
{
return omap_mmc_init(0, 0, 0, -1, -1);
}
#endif
#if defined(CONFIG_MMC)
void board_mmc_power_init(void)
{
twl4030_power_mmc_init(0);
}
#endif
/*
* Routine: get_board_mem_timings
* Description: If we use SPL then there is no x-loader nor config header
* so we have to setup the DDR timings ourself on the first bank. This
* provides the timing values back to the function that configures
* the memory. We have either one or two banks of 128MB DDR.
*/
void get_board_mem_timings(struct board_sdrc_timings *timings)
{
struct tricorder_eeprom eeprom;
get_eeprom(&eeprom);
/* General SDRC config */
if (eeprom.board_version[0] > 'D') {
/* use optimized timings for our SDRAM device */
timings->mcfg = MCFG((256 << 20), 14);
#define MT46H64M32_TDAL 6 /* Twr/Tck + Trp/tck */
/* 15/6 + 18/6 = 5.5 -> 6 */
#define MT46H64M32_TDPL 3 /* 15/6 = 2.5 -> 3 (Twr) */
#define MT46H64M32_TRRD 2 /* 12/6 = 2 */
#define MT46H64M32_TRCD 3 /* 18/6 = 3 */
#define MT46H64M32_TRP 3 /* 18/6 = 3 */
#define MT46H64M32_TRAS 7 /* 42/6 = 7 */
#define MT46H64M32_TRC 10 /* 60/6 = 10 */
#define MT46H64M32_TRFC 12 /* 72/6 = 12 */
timings->ctrla = ACTIM_CTRLA(MT46H64M32_TRFC, MT46H64M32_TRC,
MT46H64M32_TRAS, MT46H64M32_TRP,
MT46H64M32_TRCD, MT46H64M32_TRRD,
MT46H64M32_TDPL,
MT46H64M32_TDAL);
#define MT46H64M32_TWTR 1
#define MT46H64M32_TCKE 1
#define MT46H64M32_XSR 19 /* 112.5/6 = 18.75 => ~19 */
#define MT46H64M32_TXP 1
timings->ctrlb = ACTIM_CTRLB(MT46H64M32_TWTR, MT46H64M32_TCKE,
MT46H64M32_TXP, MT46H64M32_XSR);
timings->mr = MICRON_V_MR_165;
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
} else {
/* use conservative beagleboard timings as default */
timings->mcfg = MICRON_V_MCFG_165(128 << 20);
timings->ctrla = MICRON_V_ACTIMA_165;
timings->ctrlb = MICRON_V_ACTIMB_165;
timings->mr = MICRON_V_MR_165;
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
}
}
|
