1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
|
/*
* Copyright 2015 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <fsl_ddr_sdram.h>
#include <fsl_ddr_dimm_params.h>
#include <asm/arch/soc.h>
#include "ddr.h"
DECLARE_GLOBAL_DATA_PTR;
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
u8 dq_mapping_0, dq_mapping_2, dq_mapping_3;
#endif
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
ulong ddr_freq;
int slot;
if (ctrl_num > 2) {
printf("Not supported controller number %d\n", ctrl_num);
return;
}
for (slot = 0; slot < CONFIG_DIMM_SLOTS_PER_CTLR; slot++) {
if (pdimm[slot].n_ranks)
break;
}
if (slot >= CONFIG_DIMM_SLOTS_PER_CTLR)
return;
/*
* we use identical timing for all slots. If needed, change the code
* to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
*/
if (popts->registered_dimm_en)
pbsp = rdimms[ctrl_num];
else
pbsp = udimms[ctrl_num];
/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
* freqency and n_banks specified in board_specific_parameters table.
*/
ddr_freq = get_ddr_freq(ctrl_num) / 1000000;
while (pbsp->datarate_mhz_high) {
if (pbsp->n_ranks == pdimm[slot].n_ranks &&
(pdimm[slot].rank_density >> 30) >= pbsp->rank_gb) {
if (ddr_freq <= pbsp->datarate_mhz_high) {
popts->clk_adjust = pbsp->clk_adjust;
popts->wrlvl_start = pbsp->wrlvl_start;
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
goto found;
}
pbsp_highest = pbsp;
}
pbsp++;
}
if (pbsp_highest) {
printf("Error: board specific timing not found for data rate %lu MT/s\n"
"Trying to use the highest speed (%u) parameters\n",
ddr_freq, pbsp_highest->datarate_mhz_high);
popts->clk_adjust = pbsp_highest->clk_adjust;
popts->wrlvl_start = pbsp_highest->wrlvl_start;
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
} else {
panic("DIMM is not supported by this board");
}
found:
debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
"\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, wrlvl_ctrl_3 0x%x\n",
pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
pbsp->wrlvl_ctl_3);
#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
if (ctrl_num == CONFIG_DP_DDR_CTRL) {
/* force DDR bus width to 32 bits */
popts->data_bus_width = 1;
popts->otf_burst_chop_en = 0;
popts->burst_length = DDR_BL8;
popts->bstopre = 0; /* enable auto precharge */
/*
* Layout optimization results byte mapping
* Byte 0 -> Byte ECC
* Byte 1 -> Byte 3
* Byte 2 -> Byte 2
* Byte 3 -> Byte 1
* Byte ECC -> Byte 0
*/
dq_mapping_0 = pdimm[slot].dq_mapping[0];
dq_mapping_2 = pdimm[slot].dq_mapping[2];
dq_mapping_3 = pdimm[slot].dq_mapping[3];
pdimm[slot].dq_mapping[0] = pdimm[slot].dq_mapping[8];
pdimm[slot].dq_mapping[1] = pdimm[slot].dq_mapping[9];
pdimm[slot].dq_mapping[2] = pdimm[slot].dq_mapping[6];
pdimm[slot].dq_mapping[3] = pdimm[slot].dq_mapping[7];
pdimm[slot].dq_mapping[6] = dq_mapping_2;
pdimm[slot].dq_mapping[7] = dq_mapping_3;
pdimm[slot].dq_mapping[8] = dq_mapping_0;
pdimm[slot].dq_mapping[9] = 0;
pdimm[slot].dq_mapping[10] = 0;
pdimm[slot].dq_mapping[11] = 0;
pdimm[slot].dq_mapping[12] = 0;
pdimm[slot].dq_mapping[13] = 0;
pdimm[slot].dq_mapping[14] = 0;
pdimm[slot].dq_mapping[15] = 0;
pdimm[slot].dq_mapping[16] = 0;
pdimm[slot].dq_mapping[17] = 0;
}
#endif
/* To work at higher than 1333MT/s */
popts->half_strength_driver_enable = 0;
/*
* Write leveling override
*/
popts->wrlvl_override = 1;
popts->wrlvl_sample = 0x0; /* 32 clocks */
/*
* Rtt and Rtt_WR override
*/
popts->rtt_override = 0;
/* Enable ZQ calibration */
popts->zq_en = 1;
if (ddr_freq < 2350) {
if (pdimm[0].n_ranks == 2 && pdimm[1].n_ranks == 2) {
/* four chip-selects */
popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm);
popts->twot_en = 1; /* enable 2T timing */
} else {
popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
DDR_CDR1_ODT(DDR_CDR_ODT_60ohm);
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_60ohm) |
DDR_CDR2_VREF_RANGE_2;
}
} else {
popts->ddr_cdr1 = DDR_CDR1_DHC_EN |
DDR_CDR1_ODT(DDR_CDR_ODT_100ohm);
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_100ohm) |
DDR_CDR2_VREF_RANGE_2;
}
}
phys_size_t initdram(int board_type)
{
phys_size_t dram_size;
#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
return fsl_ddr_sdram_size();
#else
puts("Initializing DDR....using SPD\n");
dram_size = fsl_ddr_sdram();
#endif
return dram_size;
}
void dram_init_banksize(void)
{
#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
phys_size_t dp_ddr_size;
#endif
/*
* gd->secure_ram tracks the location of secure memory.
* It was set as if the memory starts from 0.
* The address needs to add the offset of its bank.
*/
gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
if (gd->ram_size > CONFIG_SYS_LS2_DDR_BLOCK1_SIZE) {
gd->bd->bi_dram[0].size = CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
gd->bd->bi_dram[1].size = gd->ram_size -
CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
gd->secure_ram = gd->bd->bi_dram[1].start +
gd->secure_ram -
CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
gd->secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
#endif
} else {
gd->bd->bi_dram[0].size = gd->ram_size;
#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
gd->secure_ram = gd->bd->bi_dram[0].start + gd->secure_ram;
gd->secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
#endif
}
#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
if (soc_has_dp_ddr()) {
/* initialize DP-DDR here */
puts("DP-DDR: ");
/*
* DDR controller use 0 as the base address for binding.
* It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
*/
dp_ddr_size = fsl_other_ddr_sdram(CONFIG_SYS_DP_DDR_BASE_PHY,
CONFIG_DP_DDR_CTRL,
CONFIG_DP_DDR_NUM_CTRLS,
CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR,
NULL, NULL, NULL);
if (dp_ddr_size) {
gd->bd->bi_dram[2].start = CONFIG_SYS_DP_DDR_BASE;
gd->bd->bi_dram[2].size = dp_ddr_size;
} else {
puts("Not detected");
}
}
#endif
}
|
