1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
|
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2018 Microsemi Corporation
*/
#include <common.h>
#include <asm/io.h>
#include <led.h>
#include <miiphy.h>
enum {
BOARD_TYPE_PCB110 = 0xAABBCE00,
BOARD_TYPE_PCB111,
BOARD_TYPE_PCB112,
};
int board_early_init_r(void)
{
/* Prepare SPI controller to be used in master mode */
writel(0, BASE_CFG + ICPU_SW_MODE);
clrsetbits_le32(BASE_CFG + ICPU_GENERAL_CTRL,
ICPU_GENERAL_CTRL_IF_SI_OWNER_M,
ICPU_GENERAL_CTRL_IF_SI_OWNER(2));
/* Address of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE;
/* LED setup */
if (IS_ENABLED(CONFIG_LED))
led_default_state();
return 0;
}
static void vcoreiii_gpio_set_alternate(int gpio, int mode)
{
u32 mask;
u32 val0, val1;
void __iomem *reg0, *reg1;
if (gpio < 32) {
mask = BIT(gpio);
reg0 = BASE_DEVCPU_GCB + GPIO_GPIO_ALT(0);
reg1 = BASE_DEVCPU_GCB + GPIO_GPIO_ALT(1);
} else {
gpio -= 32;
mask = BIT(gpio);
reg0 = BASE_DEVCPU_GCB + GPIO_GPIO_ALT1(0);
reg1 = BASE_DEVCPU_GCB + GPIO_GPIO_ALT1(1);
}
val0 = readl(reg0);
val1 = readl(reg1);
if (mode == 1) {
writel(val0 | mask, reg0);
writel(val1 & ~mask, reg1);
} else if (mode == 2) {
writel(val0 & ~mask, reg0);
writel(val1 | mask, reg1);
} else if (mode == 3) {
writel(val0 | mask, reg0);
writel(val1 | mask, reg1);
} else {
writel(val0 & ~mask, reg0);
writel(val1 & ~mask, reg1);
}
}
int board_phy_config(struct phy_device *phydev)
{
if (gd->board_type == BOARD_TYPE_PCB110 ||
gd->board_type == BOARD_TYPE_PCB112) {
phy_write(phydev, 0, 31, 0x10);
phy_write(phydev, 0, 18, 0x80F0);
while (phy_read(phydev, 0, 18) & 0x8000)
;
phy_write(phydev, 0, 31, 0);
}
if (gd->board_type == BOARD_TYPE_PCB111) {
phy_write(phydev, 0, 31, 0x10);
phy_write(phydev, 0, 18, 0x80A0);
while (phy_read(phydev, 0, 18) & 0x8000)
;
phy_write(phydev, 0, 14, 0x800);
phy_write(phydev, 0, 31, 0);
}
return 0;
}
void board_debug_uart_init(void)
{
/* too early for the pinctrl driver, so configure the UART pins here */
vcoreiii_gpio_set_alternate(10, 1);
vcoreiii_gpio_set_alternate(11, 1);
}
static void do_board_detect(void)
{
int i;
u16 pval;
/* MIIM 1 + 2 MDC/MDIO */
for (i = 56; i < 60; i++)
vcoreiii_gpio_set_alternate(i, 1);
/* small delay for settling the pins */
mdelay(30);
if (mscc_phy_rd(0, 0x10, 0x3, &pval) == 0 &&
((pval >> 4) & 0x3F) == 0x3c) {
gd->board_type = BOARD_TYPE_PCB112; /* Serval2-NID */
} else if (mscc_phy_rd(1, 0x0, 0x3, &pval) == 0 &&
((pval >> 4) & 0x3F) == 0x3c) {
gd->board_type = BOARD_TYPE_PCB110; /* Jr2-24 */
} else {
/* Fall-back */
gd->board_type = BOARD_TYPE_PCB111; /* Jr2-48 */
}
}
#if defined(CONFIG_MULTI_DTB_FIT)
int board_fit_config_name_match(const char *name)
{
if (gd->board_type == BOARD_TYPE_PCB110 &&
strcmp(name, "jr2_pcb110") == 0)
return 0;
if (gd->board_type == BOARD_TYPE_PCB111 &&
strcmp(name, "jr2_pcb111") == 0)
return 0;
if (gd->board_type == BOARD_TYPE_PCB112 &&
strcmp(name, "serval2_pcb112") == 0)
return 0;
return -1;
}
#endif
#if defined(CONFIG_DTB_RESELECT)
int embedded_dtb_select(void)
{
do_board_detect();
fdtdec_setup();
return 0;
}
#endif
|
