1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
|
// SPDX-License-Identifier: GPL-2.0
/*
* Copyright 2008 Freescale Semiconductor, Inc.
*/
#include <common.h>
#include <i2c.h>
#include <linux/delay.h>
#include <fsl_ddr_sdram.h>
#include <fsl_ddr_dimm_params.h>
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
/*
* Factors to consider for clock adjust:
* - number of chips on bus
* - position of slot
* - DDR1 vs. DDR2?
* - ???
*
* This needs to be determined on a board-by-board basis.
* 0110 3/4 cycle late
* 0111 7/8 cycle late
*/
popts->clk_adjust = 7;
/*
* Factors to consider for CPO:
* - frequency
* - ddr1 vs. ddr2
*/
popts->cpo_override = 10;
/*
* Factors to consider for write data delay:
* - number of DIMMs
*
* 1 = 1/4 clock delay
* 2 = 1/2 clock delay
* 3 = 3/4 clock delay
* 4 = 1 clock delay
* 5 = 5/4 clock delay
* 6 = 3/2 clock delay
*/
popts->write_data_delay = 3;
/*
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed
*/
popts->half_strength_driver_enable = 0;
}
#ifdef CONFIG_SPD_EEPROM
/*
* Workaround for hardware errata. An i2c address conflict
* existed on earlier boards; the workaround moved the DDR
* SPD from 0x51 to 0x53. So we try and read 0x53 1st, and
* if that fails, then fall back to reading at 0x51.
*/
void get_spd(generic_spd_eeprom_t *spd, u8 i2c_address)
{
int ret;
#ifdef ALT_SPD_EEPROM_ADDRESS
if (i2c_address == SPD_EEPROM_ADDRESS) {
ret = i2c_read(ALT_SPD_EEPROM_ADDRESS, 0, 1, (uchar *)spd,
sizeof(generic_spd_eeprom_t));
if (ret == 0)
return; /* Good data at 0x53 */
memset(spd, 0, sizeof(generic_spd_eeprom_t));
}
#endif
ret = i2c_read(i2c_address, 0, 1, (uchar *)spd,
sizeof(generic_spd_eeprom_t));
if (ret) {
printf("DDR: failed to read SPD from addr %u\n", i2c_address);
memset(spd, 0, sizeof(generic_spd_eeprom_t));
}
}
#else
/*
* fixed_sdram init -- doesn't use serial presence detect.
* Assumes 256MB DDR2 SDRAM SODIMM, without ECC, running at DDR400 speed.
*/
phys_size_t fixed_sdram(void)
{
struct ccsr_ddr __iomem *ddr =
(struct ccsr_ddr __iomem *)(CONFIG_SYS_FSL_DDR_ADDR);
out_be32(&ddr->cs0_bnds, 0x0000007f);
out_be32(&ddr->cs1_bnds, 0x008000ff);
out_be32(&ddr->cs2_bnds, 0x00000000);
out_be32(&ddr->cs3_bnds, 0x00000000);
out_be32(&ddr->cs0_config, 0x80010101);
out_be32(&ddr->cs1_config, 0x80010101);
out_be32(&ddr->cs2_config, 0x00000000);
out_be32(&ddr->cs3_config, 0x00000000);
out_be32(&ddr->timing_cfg_3, 0x00000000);
out_be32(&ddr->timing_cfg_0, 0x00220802);
out_be32(&ddr->timing_cfg_1, 0x38377322);
out_be32(&ddr->timing_cfg_2, 0x0fa044C7);
out_be32(&ddr->sdram_cfg, 0x4300C000);
out_be32(&ddr->sdram_cfg_2, 0x24401000);
out_be32(&ddr->sdram_mode, 0x23C00542);
out_be32(&ddr->sdram_mode_2, 0x00000000);
out_be32(&ddr->sdram_interval, 0x05080100);
out_be32(&ddr->sdram_md_cntl, 0x00000000);
out_be32(&ddr->sdram_data_init, 0x00000000);
out_be32(&ddr->sdram_clk_cntl, 0x03800000);
asm("sync;isync;msync");
udelay(500);
#ifdef CONFIG_DDR_ECC
/* Enable ECC checking */
out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL | 0x20000000);
#else
out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
#endif
return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
}
#endif
|
