1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
|
// SPDX-License-Identifier: GPL-2.0+
/*
* board.c
*
* Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
*/
#include <common.h>
#include <env.h>
#include <net.h>
#include <serial.h>
#include <asm/arch/cpu.h>
#include <asm/arch/hardware.h>
#include <asm/arch/ddr_defs.h>
#include <asm/arch/clock.h>
#include <asm/arch/sys_proto.h>
#include <i2c.h>
#include <phy.h>
#include <cpsw.h>
#include "board.h"
DECLARE_GLOBAL_DATA_PTR;
static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
#if defined(CONFIG_SPL_BUILD)
/* DDR3 RAM timings */
static const struct ddr_data ddr3_data = {
.datardsratio0 = MT41K128MJT187E_RD_DQS,
.datawdsratio0 = MT41K128MJT187E_WR_DQS,
.datafwsratio0 = MT41K128MJT187E_PHY_FIFO_WE,
.datawrsratio0 = MT41K128MJT187E_PHY_WR_DATA,
};
static const struct cmd_control ddr3_cmd_ctrl_data = {
.cmd0csratio = MT41K128MJT187E_RATIO,
.cmd0iclkout = MT41K128MJT187E_INVERT_CLKOUT,
.cmd1csratio = MT41K128MJT187E_RATIO,
.cmd1iclkout = MT41K128MJT187E_INVERT_CLKOUT,
.cmd2csratio = MT41K128MJT187E_RATIO,
.cmd2iclkout = MT41K128MJT187E_INVERT_CLKOUT,
};
static struct emif_regs ddr3_emif_reg_data = {
.sdram_config = MT41K128MJT187E_EMIF_SDCFG,
.ref_ctrl = MT41K128MJT187E_EMIF_SDREF,
.sdram_tim1 = MT41K128MJT187E_EMIF_TIM1,
.sdram_tim2 = MT41K128MJT187E_EMIF_TIM2,
.sdram_tim3 = MT41K128MJT187E_EMIF_TIM3,
.zq_config = MT41K128MJT187E_ZQ_CFG,
.emif_ddr_phy_ctlr_1 = MT41K128MJT187E_EMIF_READ_LATENCY |
PHY_EN_DYN_PWRDN,
};
const struct ctrl_ioregs ddr3_ioregs = {
.cm0ioctl = MT41K128MJT187E_IOCTRL_VALUE,
.cm1ioctl = MT41K128MJT187E_IOCTRL_VALUE,
.cm2ioctl = MT41K128MJT187E_IOCTRL_VALUE,
.dt0ioctl = MT41K128MJT187E_IOCTRL_VALUE,
.dt1ioctl = MT41K128MJT187E_IOCTRL_VALUE,
};
#ifdef CONFIG_SPL_OS_BOOT
int spl_start_uboot(void)
{
/* break into full u-boot on 'c' */
return serial_tstc() && serial_getc() == 'c';
}
#endif
#define OSC (V_OSCK/1000000)
const struct dpll_params dpll_ddr_266 = {
266, OSC-1, 1, -1, -1, -1, -1};
const struct dpll_params dpll_ddr_303 = {
303, OSC-1, 1, -1, -1, -1, -1};
const struct dpll_params dpll_ddr_400 = {
400, OSC-1, 1, -1, -1, -1, -1};
void am33xx_spl_board_init(void)
{
/*
* The pengwyn board uses the TPS650250 PMIC without I2C
* interface and will output the following fixed voltages:
* DCDC1=3V3 (IO) DCDC2=1V5 (DDR) DCDC3=1V26 (Vmpu)
* VLDO1=1V8 (IO) VLDO2=1V8(IO)
* Vcore=1V1 is fixed, generated by TPS62231
*/
/* Get the frequency */
dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
/* Set CORE Frequencies to OPP100 */
do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
/* 720MHz cpu, this might change on newer board revisions */
dpll_mpu_opp100.m = MPUPLL_M_720;
do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
}
const struct dpll_params *get_dpll_ddr_params(void)
{
/* future configs can return other clock settings */
return &dpll_ddr_303;
}
void set_uart_mux_conf(void)
{
enable_uart0_pin_mux();
}
void set_mux_conf_regs(void)
{
enable_board_pin_mux();
}
void sdram_init(void)
{
config_ddr(303, &ddr3_ioregs, &ddr3_data,
&ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
}
#endif /* if CONFIG_SPL_BUILD */
/*
* Basic board specific setup. Pinmux has been handled already.
*/
int board_init(void)
{
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
gpmc_init();
return 0;
}
#ifdef CONFIG_DRIVER_TI_CPSW
static void cpsw_control(int enabled)
{
/* VTP can be added here */
return;
}
static struct cpsw_slave_data cpsw_slaves[] = {
{
.slave_reg_ofs = 0x208,
.sliver_reg_ofs = 0xd80,
.phy_addr = 1,
.phy_if = PHY_INTERFACE_MODE_MII,
},
};
static struct cpsw_platform_data cpsw_data = {
.mdio_base = CPSW_MDIO_BASE,
.cpsw_base = CPSW_BASE,
.mdio_div = 0xff,
.channels = 8,
.cpdma_reg_ofs = 0x800,
.slaves = 1,
.slave_data = cpsw_slaves,
.ale_reg_ofs = 0xd00,
.ale_entries = 1024,
.host_port_reg_ofs = 0x108,
.hw_stats_reg_ofs = 0x900,
.bd_ram_ofs = 0x2000,
.mac_control = (1 << 5),
.control = cpsw_control,
.host_port_num = 0,
.version = CPSW_CTRL_VERSION_2,
};
int board_eth_init(bd_t *bis)
{
int rv, n = 0;
uint8_t mac_addr[6];
uint32_t mac_hi, mac_lo;
if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
printf("<ethaddr> not set. Reading from E-fuse\n");
/* try reading mac address from efuse */
mac_lo = readl(&cdev->macid0l);
mac_hi = readl(&cdev->macid0h);
mac_addr[0] = mac_hi & 0xFF;
mac_addr[1] = (mac_hi & 0xFF00) >> 8;
mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
mac_addr[4] = mac_lo & 0xFF;
mac_addr[5] = (mac_lo & 0xFF00) >> 8;
if (is_valid_ethaddr(mac_addr))
eth_env_set_enetaddr("ethaddr", mac_addr);
else
return n;
}
writel(MII_MODE_ENABLE, &cdev->miisel);
rv = cpsw_register(&cpsw_data);
if (rv < 0)
printf("Error %d registering CPSW switch\n", rv);
else
n += rv;
return n;
}
#endif /* if CONFIG_DRIVER_TI_CPSW */
|
