1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
|
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2016 NXP Semiconductors
* Author: Fabio Estevam <fabio.estevam@nxp.com>
*/
#include <init.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/mx7-pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/mach-imx/hab.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/io.h>
#include <common.h>
#include <env.h>
#include <asm/arch/crm_regs.h>
#include <netdev.h>
#include <power/pmic.h>
#include <power/pfuze3000_pmic.h>
#include "../freescale/common/pfuze.h"
#include <asm/setup.h>
#include <asm/bootm.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUS_PU100KOHM | \
PAD_CTL_HYS)
int dram_init(void)
{
gd->ram_size = PHYS_SDRAM_SIZE;
/* Subtract the defined OPTEE runtime firmware length */
#ifdef CONFIG_OPTEE_TZDRAM_SIZE
gd->ram_size -= CONFIG_OPTEE_TZDRAM_SIZE;
#endif
return 0;
}
static iomux_v3_cfg_t const wdog_pads[] = {
MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t const uart1_pads[] = {
MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
};
int board_early_init_f(void)
{
setup_iomux_uart();
return 0;
}
#ifdef CONFIG_DM_PMIC
int power_init_board(void)
{
struct udevice *dev;
int ret, dev_id, rev_id;
ret = pmic_get("pfuze3000@8", &dev);
if (ret == -ENODEV)
return 0;
if (ret != 0)
return ret;
dev_id = pmic_reg_read(dev, PFUZE3000_DEVICEID);
rev_id = pmic_reg_read(dev, PFUZE3000_REVID);
printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
/* disable Low Power Mode during standby mode */
pmic_reg_write(dev, PFUZE3000_LDOGCTL, 1);
return 0;
}
#endif
int board_eth_init(bd_t *bis)
{
int ret = 0;
#ifdef CONFIG_USB_ETHER
ret = usb_eth_initialize(bis);
if (ret < 0)
printf("Error %d registering USB ether.\n", ret);
#endif
return ret;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
return 0;
}
int checkboard(void)
{
char *mode;
if (IS_ENABLED(CONFIG_ARMV7_BOOT_SEC_DEFAULT))
mode = "secure";
else
mode = "non-secure";
#ifdef CONFIG_OPTEE_TZDRAM_SIZE
unsigned long optee_start, optee_end;
optee_end = PHYS_SDRAM + PHYS_SDRAM_SIZE;
optee_start = optee_end - CONFIG_OPTEE_TZDRAM_SIZE;
printf("Board: WARP7 in %s mode OPTEE DRAM 0x%08lx-0x%08lx\n",
mode, optee_start, optee_end);
#else
printf("Board: WARP7 in %s mode\n", mode);
#endif
return 0;
}
int board_late_init(void)
{
struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
#ifdef CONFIG_SERIAL_TAG
struct tag_serialnr serialnr;
char serial_string[0x20];
#endif
imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
set_wdog_reset(wdog);
/*
* Do not assert internal WDOG_RESET_B_DEB(controlled by bit 4),
* since we use PMIC_PWRON to reset the board.
*/
clrsetbits_le16(&wdog->wcr, 0, 0x10);
#ifdef CONFIG_IMX_HAB
/* Determine HAB state */
env_set_ulong(HAB_ENABLED_ENVNAME, imx_hab_is_enabled());
#else
env_set_ulong(HAB_ENABLED_ENVNAME, 0);
#endif
#ifdef CONFIG_SERIAL_TAG
/* Set serial# standard environment variable based on OTP settings */
get_board_serial(&serialnr);
snprintf(serial_string, sizeof(serial_string), "WaRP7-0x%08x%08x",
serialnr.low, serialnr.high);
env_set("serial#", serial_string);
#endif
return 0;
}
|
