1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
|
Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY
Some boards require special tuning values, particularly when it comes to
clock delays. You can specify clock delay values by adding
micrel-specific properties to an Ethernet OF device node.
Note that these settings are applied after any phy-specific fixup from
phy_fixup_list (see phy_init_hw() from drivers/net/phy/phy_device.c),
and therefore may overwrite them.
KSZ9021:
All skew control options are specified in picoseconds. The minimum
value is 0, the maximum value is 1800, and it is incremented by 120ps
steps.
The KSZ9021 hardware supports a range of skew values from negative to
positive, where the specific range is property dependent. All values
specified in the devicetree are offset by the minimum value so they
can be represented as positive integers in the devicetree since it's
difficult to represent a negative number in the devictree.
The following 4-bit values table applies to all the skew properties:
Pad Skew Value Delay (ps) Devicetree Value
------------------------------------------------------
0000 -840ps 0
0001 -720ps 120
0010 -600ps 240
0011 -480ps 360
0100 -360ps 480
0101 -240ps 600
0110 -120ps 720
0111 0ps 840
1000 120ps 960
1001 240ps 1080
1010 360ps 1200
1011 480ps 1320
1100 600ps 1440
1101 720ps 1560
1110 840ps 1680
1111 960ps 1800
Optional properties:
- rxc-skew-ps : Skew control of RXC pad
- rxdv-skew-ps : Skew control of RX CTL pad
- txc-skew-ps : Skew control of TXC pad
- txen-skew-ps : Skew control of TX CTL pad
- rxd0-skew-ps : Skew control of RX data 0 pad
- rxd1-skew-ps : Skew control of RX data 1 pad
- rxd2-skew-ps : Skew control of RX data 2 pad
- rxd3-skew-ps : Skew control of RX data 3 pad
- txd0-skew-ps : Skew control of TX data 0 pad
- txd1-skew-ps : Skew control of TX data 1 pad
- txd2-skew-ps : Skew control of TX data 2 pad
- txd3-skew-ps : Skew control of TX data 3 pad
KSZ9031:
All skew control options are specified in picoseconds. The minimum
value is 0, and the maximum is property-dependent. The increment
step is 60ps.
The KSZ9031 hardware supports a range of skew values from negative to
positive, where the specific range is property dependent. All values
specified in the devicetree are offset by the minimum value so they
can be represented as positive integers in the devicetree since it's
difficult to represent a negative number in the devictree.
The following 5-bit values table apply to rxc-skew-ps and txc-skew-ps.
Pad Skew Value Delay (ps) Devicetree Value
------------------------------------------------------
0_0000 -900ps 0
0_0001 -840ps 60
0_0010 -780ps 120
0_0011 -720ps 180
0_0100 -660ps 240
0_0101 -600ps 300
0_0110 -540ps 360
0_0111 -480ps 420
0_1000 -420ps 480
0_1001 -360ps 540
0_1010 -300ps 600
0_1011 -240ps 660
0_1100 -180ps 720
0_1101 -120ps 780
0_1110 -60ps 840
0_1111 0ps 900
1_0000 60ps 960
1_0001 120ps 1020
1_0010 180ps 1080
1_0011 240ps 1140
1_0100 300ps 1200
1_0101 360ps 1260
1_0110 420ps 1320
1_0111 480ps 1380
1_1000 540ps 1440
1_1001 600ps 1500
1_1010 660ps 1560
1_1011 720ps 1620
1_1100 780ps 1680
1_1101 840ps 1740
1_1110 900ps 1800
1_1111 960ps 1860
The following 4-bit values table apply to the txdX-skew-ps, rxdX-skew-ps
data pads, and the rxdv-skew-ps, txen-skew-ps control pads.
Pad Skew Value Delay (ps) Devicetree Value
------------------------------------------------------
0000 -420ps 0
0001 -360ps 60
0010 -300ps 120
0011 -240ps 180
0100 -180ps 240
0101 -120ps 300
0110 -60ps 360
0111 0ps 420
1000 60ps 480
1001 120ps 540
1010 180ps 600
1011 240ps 660
1100 300ps 720
1101 360ps 780
1110 420ps 840
1111 480ps 900
Optional properties:
Maximum value of 1860:
- rxc-skew-ps : Skew control of RX clock pad
- txc-skew-ps : Skew control of TX clock pad
Maximum value of 900:
- rxdv-skew-ps : Skew control of RX CTL pad
- txen-skew-ps : Skew control of TX CTL pad
- rxd0-skew-ps : Skew control of RX data 0 pad
- rxd1-skew-ps : Skew control of RX data 1 pad
- rxd2-skew-ps : Skew control of RX data 2 pad
- rxd3-skew-ps : Skew control of RX data 3 pad
- txd0-skew-ps : Skew control of TX data 0 pad
- txd1-skew-ps : Skew control of TX data 1 pad
- txd2-skew-ps : Skew control of TX data 2 pad
- txd3-skew-ps : Skew control of TX data 3 pad
Examples:
/* Attach to an Ethernet device with autodetected PHY */
&enet {
rxc-skew-ps = <1800>;
rxdv-skew-ps = <0>;
txc-skew-ps = <1800>;
txen-skew-ps = <0>;
status = "okay";
};
/* Attach to an explicitly-specified PHY */
mdio {
phy0: ethernet-phy@0 {
rxc-skew-ps = <1800>;
rxdv-skew-ps = <0>;
txc-skew-ps = <1800>;
txen-skew-ps = <0>;
reg = <0>;
};
};
ethernet@70000 {
status = "okay";
phy = <&phy0>;
phy-mode = "rgmii-id";
};
References
Micrel ksz9021rl/rn Data Sheet, Revision 1.2. Dated 2/13/2014.
http://www.micrel.com/_PDF/Ethernet/datasheets/ksz9021rl-rn_ds.pdf
Micrel ksz9031rnx Data Sheet, Revision 2.1. Dated 11/20/2014.
http://www.micrel.com/_PDF/Ethernet/datasheets/KSZ9031RNX.pdf
Notes:
Note that a previous version of the Micrel ksz9021rl/rn Data Sheet
was missing extended register 106 (transmit data pad skews), and
incorrectly specified the ps per step as 200ps/step instead of
120ps/step. The latest update to this document reflects the latest
revision of the Micrel specification even though usage in the kernel
still reflects that incorrect document.
|
