blob: b7c29f2fd30de36103f218ae65b3559a32b49f70 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
|
#
# Boot count configuration
#
menuconfig BOOTCOUNT_LIMIT
bool "Enable support for checking boot count limit"
help
Enable checking for exceeding the boot count limit.
More information: http://www.denx.de/wiki/DULG/UBootBootCountLimit
if BOOTCOUNT_LIMIT
choice
prompt "Boot count device"
default BOOTCOUNT_AM33XX if AM33XX || SOC_DA8XX
default BOOTCOUNT_AT91 if AT91SAM9XE
default BOOTCOUNT_GENERIC
config BOOTCOUNT_GENERIC
bool "Generic default boot counter"
help
Generic bootcount stored at SYS_BOOTCOUNT_ADDR.
SYS_BOOTCOUNT_ADDR:
Set to the address where the bootcount and bootcount magic
will be stored.
config BOOTCOUNT_EXT
bool "Boot counter on EXT filesystem"
help
Add support for maintaining boot count in a file on an EXT
filesystem.
config BOOTCOUNT_AM33XX
bool "Boot counter in AM33XX RTC IP block"
depends on AM33XX || SOC_DA8XX
select SPL_AM33XX_ENABLE_RTC32K_OSC if AM33XX
help
A bootcount driver for the RTC IP block found on many TI platforms.
This requires the RTC clocks, etc, to be enabled prior to use and
not all boards with this IP block on it will have the RTC in use.
config BOOTCOUNT_ENV
bool "Boot counter in environment"
help
If no softreset save registers are found on the hardware
"bootcount" is stored in the environment. To prevent a
saveenv on all reboots, the environment variable
"upgrade_available" is used. If "upgrade_available" is
0, "bootcount" is always 0, if "upgrade_available" is
1 "bootcount" is incremented in the environment.
So the Userspace Application must set the "upgrade_available"
and "bootcount" variable to 0, if a boot was successfully.
config BOOTCOUNT_RAM
bool "Boot counter in RAM"
help
Store the bootcount in DRAM protected against against bit errors
due to short power loss or holding a system in RESET.
config BOOTCOUNT_I2C
bool "Boot counter on I2C device"
help
Enable support for the bootcounter on an i2c (like RTC) device.
CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
the bootcounter.
config BOOTCOUNT_AT91
bool "Boot counter for Atmel AT91SAM9XE"
depends on AT91SAM9XE
config DM_BOOTCOUNT
bool "Boot counter in a device-model device"
help
Enables reading/writing the bootcount in a device-model based
backing store. If an entry in /chosen/u-boot,bootcount-device
exists, this will be the preferred bootcount device; otherwise
the first available bootcount device will be used.
endchoice
if DM_BOOTCOUNT
menu "Backing stores for device-model backed bootcount"
config DM_BOOTCOUNT_RTC
bool "Support RTC devices as a backing store for bootcount"
depends on DM_RTC
help
Enabled reading/writing the bootcount in a DM RTC device.
The wrapper device is to be specified with the compatible string
'u-boot,bootcount-rtc' and the 'rtc'-property (a phandle pointing
to the underlying RTC device) and an optional 'offset' property
are supported.
Accesses to the backing store are performed using the write16
and read16 ops of DM RTC devices.
endmenu
endif
config BOOTCOUNT_BOOTLIMIT
int "Maximum number of reboot cycles allowed"
default 0
help
Set the Maximum number of reboot cycles allowed without the boot
counter being cleared.
If set to 0 do not set a boot limit in the environment.
config BOOTCOUNT_ALEN
int "I2C address length"
default 1
depends on BOOTCOUNT_I2C
help
Length of the the I2C address at SYS_BOOTCOUNT_ADDR for storing
the boot counter.
config SYS_BOOTCOUNT_SINGLEWORD
bool "Use single word to pack boot count and magic value"
depends on BOOTCOUNT_GENERIC
help
This option enables packing boot count magic value and boot count
into single word (32 bits).
config SYS_BOOTCOUNT_EXT_INTERFACE
string "Interface on which to find boot counter EXT filesystem"
default "mmc"
depends on BOOTCOUNT_EXT
help
Set the interface to use when locating the filesystem to use for the
boot counter.
config SYS_BOOTCOUNT_EXT_DEVPART
string "Partition of the boot counter EXT filesystem"
default "0:1"
depends on BOOTCOUNT_EXT
help
Set the partition to use when locating the filesystem to use for the
boot counter.
config SYS_BOOTCOUNT_EXT_NAME
string "Path and filename of the EXT filesystem based boot counter"
default "/boot/failures"
depends on BOOTCOUNT_EXT
help
Set the filename and path of the file used to store the boot counter.
config SYS_BOOTCOUNT_ADDR
hex "RAM address used for reading and writing the boot counter"
default 0x44E3E000 if BOOTCOUNT_AM33XX
default 0xE0115FF8 if ARCH_LS1043A || ARCH_LS1021A
depends on BOOTCOUNT_AM33XX || BOOTCOUNT_GENERIC || BOOTCOUNT_EXT || \
BOOTCOUNT_I2C
help
Set the address used for reading and writing the boot counter.
config SYS_BOOTCOUNT_MAGIC
hex "Magic value for the boot counter"
default 0xB001C041
help
Set the magic value used for the boot counter.
endif
|
