1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
|
menu "SPI Flash Support"
config DM_SPI_FLASH
bool "Enable Driver Model for SPI flash"
depends on DM && DM_SPI
help
Enable driver model for SPI flash. This SPI flash interface
(spi_flash_probe(), spi_flash_write(), etc.) is then
implemented by the SPI flash uclass. There is one standard
SPI flash driver which knows how to probe most chips
supported by U-Boot. The uclass interface is defined in
include/spi_flash.h, but is currently fully compatible
with the old interface to avoid confusion and duplication
during the transition parent. SPI and SPI flash must be
enabled together (it is not possible to use driver model
for one and not the other).
config SPI_FLASH_SANDBOX
bool "Support sandbox SPI flash device"
depends on SANDBOX && DM_SPI_FLASH
help
Since sandbox cannot access real devices, an emulation mechanism is
provided instead. Drivers can be connected up to the sandbox SPI
bus (see CONFIG_SANDBOX_SPI) and SPI traffic will be routed to this
device. Typically the contents of the emulated SPI flash device is
stored in a file on the host filesystem.
config SPI_FLASH
bool "Legacy SPI Flash Interface support"
depends on SPI
select SPI_MEM
help
Enable the legacy SPI flash support. This will include basic
standard support for things like probing, read / write, and
erasing through cmd_sf interface.
If unsure, say N
config SF_DEFAULT_BUS
int "SPI Flash default bus identifier"
depends on SPI_FLASH || DM_SPI_FLASH
default 0
help
The default bus may be provided by the platform
to handle the common case when only a single serial
flash is present on the system.
config SF_DEFAULT_CS
int "SPI Flash default Chip-select"
depends on SPI_FLASH || DM_SPI_FLASH
default 0
help
The default chip select may be provided by the platform
to handle the common case when only a single serial
flash is present on the system.
config SF_DEFAULT_MODE
hex "SPI Flash default mode (see include/spi.h)"
depends on SPI_FLASH || DM_SPI_FLASH
default 3
help
The default mode may be provided by the platform
to handle the common case when only a single serial
flash is present on the system.
Not used for boot with device tree; the SPI driver reads
speed and mode from platdata values computed from
available node.
config SF_DEFAULT_SPEED
int "SPI Flash default speed in Hz"
depends on SPI_FLASH || DM_SPI_FLASH
default 1000000
help
The default speed may be provided by the platform
to handle the common case when only a single serial
flash is present on the system.
Not used for boot with device tree; the SPI driver reads
speed and mode from platdata values computed from
available node.
if SPI_FLASH
config SPI_FLASH_SFDP_SUPPORT
bool "SFDP table parsing support for SPI NOR flashes"
depends on !SPI_FLASH_BAR
help
Enable support for parsing and auto discovery of parameters for
SPI NOR flashes using Serial Flash Discoverable Parameters (SFDP)
tables as per JESD216 standard.
config SPI_FLASH_BAR
bool "SPI flash Bank/Extended address register support"
help
Enable the SPI flash Bank/Extended address register support.
Bank/Extended address registers are used to access the flash
which has size > 16MiB in 3-byte addressing.
config SF_DUAL_FLASH
bool "SPI DUAL flash memory support"
help
Enable this option to support two flash memories connected to a single
controller. Currently Xilinx Zynq qspi supports this.
config SPI_FLASH_ATMEL
bool "Atmel SPI flash support"
help
Add support for various Atmel SPI flash chips (AT45xxx and AT25xxx)
config SPI_FLASH_EON
bool "EON SPI flash support"
help
Add support for various EON SPI flash chips (EN25xxx)
config SPI_FLASH_GIGADEVICE
bool "GigaDevice SPI flash support"
help
Add support for various GigaDevice SPI flash chips (GD25xxx)
config SPI_FLASH_ISSI
bool "ISSI SPI flash support"
help
Add support for various ISSI SPI flash chips (ISxxx)
config SPI_FLASH_MACRONIX
bool "Macronix SPI flash support"
help
Add support for various Macronix SPI flash chips (MX25Lxxx)
config SPI_FLASH_SPANSION
bool "Spansion SPI flash support"
help
Add support for various Spansion SPI flash chips (S25FLxxx)
config SPI_FLASH_STMICRO
bool "STMicro SPI flash support"
help
Add support for various STMicro SPI flash chips (M25Pxxx and N25Qxxx)
config SPI_FLASH_SST
bool "SST SPI flash support"
help
Add support for various SST SPI flash chips (SST25xxx)
config SPI_FLASH_WINBOND
bool "Winbond SPI flash support"
help
Add support for various Winbond SPI flash chips (W25xxx)
config SPI_FLASH_XMC
bool "XMC SPI flash support"
help
Add support for various XMC (Wuhan Xinxin Semiconductor
Manufacturing Corp.) SPI flash chips (XM25xxx)
endif
config SPI_FLASH_USE_4K_SECTORS
bool "Use small 4096 B erase sectors"
depends on SPI_FLASH
default y
help
Many flash memories support erasing small (4096 B) sectors. Depending
on the usage this feature may provide performance gain in comparison
to erasing whole blocks (32/64 KiB).
Changing a small part of the flash's contents is usually faster with
small sectors. On the other hand erasing should be faster when using
64 KiB block instead of 16 × 4 KiB sectors.
Please note that some tools/drivers/filesystems may not work with
4096 B erase size (e.g. UBIFS requires 15 KiB as a minimum).
config SPI_FLASH_DATAFLASH
bool "AT45xxx DataFlash support"
depends on SPI_FLASH && DM_SPI_FLASH
help
Enable the access for SPI-flash-based AT45xxx DataFlash chips.
DataFlash is a kind of SPI flash. Most AT45 chips have two buffers
in each chip, which may be used for double buffered I/O; but this
driver doesn't (yet) use these for any kind of i/o overlap or prefetching.
Sometimes DataFlash is packaged in MMC-format cards, although the
MMC stack can't (yet?) distinguish between MMC and DataFlash
protocols during enumeration.
If unsure, say N
config SPI_FLASH_MTD
bool "SPI Flash MTD support"
depends on SPI_FLASH
help
Enable the MTD support for spi flash layer, this adapter is for
translating mtd_read/mtd_write commands into spi_flash_read/write
commands. It is not intended to use it within sf_cmd or the SPI
flash subsystem. Such an adapter is needed for subsystems like
UBI which can only operate on top of the MTD layer.
If unsure, say N
endmenu # menu "SPI Flash Support"
|
