1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
|
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2012
* Henrik Nordstrom <henrik@henriknordstrom.net>
*/
#include <common.h>
#include <command.h>
#include <asm/arch/pmic_bus.h>
#include <axp_pmic.h>
static u8 axp209_mvolt_to_cfg(int mvolt, int min, int max, int div)
{
if (mvolt < min)
mvolt = min;
else if (mvolt > max)
mvolt = max;
return (mvolt - min) / div;
}
int axp_set_dcdc2(unsigned int mvolt)
{
int rc;
u8 cfg, current;
if (mvolt == 0)
return pmic_bus_clrbits(AXP209_OUTPUT_CTRL,
AXP209_OUTPUT_CTRL_DCDC2);
rc = pmic_bus_setbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_DCDC2);
if (rc)
return rc;
cfg = axp209_mvolt_to_cfg(mvolt, 700, 2275, 25);
/* Do we really need to be this gentle? It has built-in voltage slope */
while ((rc = pmic_bus_read(AXP209_DCDC2_VOLTAGE, ¤t)) == 0 &&
current != cfg) {
if (current < cfg)
current++;
else
current--;
rc = pmic_bus_write(AXP209_DCDC2_VOLTAGE, current);
if (rc)
break;
}
return rc;
}
int axp_set_dcdc3(unsigned int mvolt)
{
u8 cfg = axp209_mvolt_to_cfg(mvolt, 700, 3500, 25);
int rc;
if (mvolt == 0)
return pmic_bus_clrbits(AXP209_OUTPUT_CTRL,
AXP209_OUTPUT_CTRL_DCDC3);
rc = pmic_bus_write(AXP209_DCDC3_VOLTAGE, cfg);
if (rc)
return rc;
return pmic_bus_setbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_DCDC3);
}
int axp_set_aldo2(unsigned int mvolt)
{
int rc;
u8 cfg, reg;
if (mvolt == 0)
return pmic_bus_clrbits(AXP209_OUTPUT_CTRL,
AXP209_OUTPUT_CTRL_LDO2);
cfg = axp209_mvolt_to_cfg(mvolt, 1800, 3300, 100);
rc = pmic_bus_read(AXP209_LDO24_VOLTAGE, ®);
if (rc)
return rc;
/* LDO2 configuration is in upper 4 bits */
reg = (reg & 0x0f) | (cfg << 4);
rc = pmic_bus_write(AXP209_LDO24_VOLTAGE, reg);
if (rc)
return rc;
return pmic_bus_setbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_LDO2);
}
int axp_set_aldo3(unsigned int mvolt)
{
u8 cfg;
int rc;
if (mvolt == 0)
return pmic_bus_clrbits(AXP209_OUTPUT_CTRL,
AXP209_OUTPUT_CTRL_LDO3);
if (mvolt == -1)
cfg = 0x80; /* determined by LDO3IN pin */
else
cfg = axp209_mvolt_to_cfg(mvolt, 700, 3500, 25);
rc = pmic_bus_write(AXP209_LDO3_VOLTAGE, cfg);
if (rc)
return rc;
return pmic_bus_setbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_LDO3);
}
int axp_set_aldo4(unsigned int mvolt)
{
int rc;
static const unsigned int vindex[] = {
1250, 1300, 1400, 1500, 1600, 1700, 1800, 1900, 2000, 2500,
2700, 2800, 3000, 3100, 3200, 3300
};
u8 cfg, reg;
if (mvolt == 0)
return pmic_bus_clrbits(AXP209_OUTPUT_CTRL,
AXP209_OUTPUT_CTRL_LDO4);
/* Translate mvolt to register cfg value, requested <= selected */
for (cfg = 15; vindex[cfg] > mvolt && cfg > 0; cfg--);
rc = pmic_bus_read(AXP209_LDO24_VOLTAGE, ®);
if (rc)
return rc;
/* LDO4 configuration is in lower 4 bits */
reg = (reg & 0xf0) | (cfg << 0);
rc = pmic_bus_write(AXP209_LDO24_VOLTAGE, reg);
if (rc)
return rc;
return pmic_bus_setbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_LDO4);
}
int axp_init(void)
{
u8 ver;
int i, rc;
rc = pmic_bus_init();
if (rc)
return rc;
rc = pmic_bus_read(AXP209_CHIP_VERSION, &ver);
if (rc)
return rc;
/* Low 4 bits is chip version */
ver &= 0x0f;
if (ver != 0x1)
return -EINVAL;
/* Mask all interrupts */
for (i = AXP209_IRQ_ENABLE1; i <= AXP209_IRQ_ENABLE5; i++) {
rc = pmic_bus_write(i, 0);
if (rc)
return rc;
}
/*
* Turn off LDOIO regulators / tri-state GPIO pins, when rebooting
* from android these are sometimes on.
*/
rc = pmic_bus_write(AXP_GPIO0_CTRL, AXP_GPIO_CTRL_INPUT);
if (rc)
return rc;
rc = pmic_bus_write(AXP_GPIO1_CTRL, AXP_GPIO_CTRL_INPUT);
if (rc)
return rc;
rc = pmic_bus_write(AXP_GPIO2_CTRL, AXP_GPIO_CTRL_INPUT);
if (rc)
return rc;
return 0;
}
int do_poweroff(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
pmic_bus_write(AXP209_SHUTDOWN, AXP209_POWEROFF);
/* infinite loop during shutdown */
while (1) {}
/* not reached */
return 0;
}
|
