path: root/drivers/spi/kirkwood_spi.c

// SPDX-License-Identifier: GPL-2.0+
/*
 * (C) Copyright 2009
 * Marvell Semiconductor <www.marvell.com>
 * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
 *
 * Derived from drivers/spi/mpc8xxx_spi.c
 */

#include <common.h>
#include <dm.h>
#include <malloc.h>
#include <spi.h>
#include <asm/io.h>
#include <asm/arch/soc.h>
#ifdef CONFIG_KIRKWOOD
#include <asm/arch/mpp.h>
#endif
#include <asm/arch-mvebu/spi.h>

static void _spi_cs_activate(struct kwspi_registers *reg)
{
	setbits_le32(&reg->ctrl, KWSPI_CSN_ACT);
}

static void _spi_cs_deactivate(struct kwspi_registers *reg)
{
	clrbits_le32(&reg->ctrl, KWSPI_CSN_ACT);
}

static int _spi_xfer(struct kwspi_registers *reg, unsigned int bitlen,
		     const void *dout, void *din, unsigned long flags)
{
	unsigned int tmpdout, tmpdin;
	int tm, isread = 0;

	debug("spi_xfer: dout %p din %p bitlen %u\n", dout, din, bitlen);

	if (flags & SPI_XFER_BEGIN)
		_spi_cs_activate(reg);

	/*
	 * handle data in 8-bit chunks
	 * TBD: 2byte xfer mode to be enabled
	 */
	clrsetbits_le32(&reg->cfg, KWSPI_XFERLEN_MASK, KWSPI_XFERLEN_1BYTE);

	while (bitlen > 4) {
		debug("loopstart bitlen %d\n", bitlen);
		tmpdout = 0;

		/* Shift data so it's msb-justified */
		if (dout)
			tmpdout = *(u32 *)dout & 0xff;

		clrbits_le32(&reg->irq_cause, KWSPI_SMEMRDIRQ);
		writel(tmpdout, &reg->dout);	/* Write the data out */
		debug("*** spi_xfer: ... %08x written, bitlen %d\n",
		      tmpdout, bitlen);

		/*
		 * Wait for SPI transmit to get out
		 * or time out (1 second = 1000 ms)
		 * The NE event must be read and cleared first
		 */
		for (tm = 0, isread = 0; tm < KWSPI_TIMEOUT; ++tm) {
			if (readl(&reg->irq_cause) & KWSPI_SMEMRDIRQ) {
				isread = 1;
				tmpdin = readl(&reg->din);
				debug("spi_xfer: din %p..%08x read\n",
				      din, tmpdin);

				if (din) {
					*((u8 *)din) = (u8)tmpdin;
					din += 1;
				}
				if (dout)
					dout += 1;
				bitlen -= 8;
			}
			if (isread)
				break;
		}
		if (tm >= KWSPI_TIMEOUT)
			printf("*** spi_xfer: Time out during SPI transfer\n");

		debug("loopend bitlen %d\n", bitlen);
	}

	if (flags & SPI_XFER_END)
		_spi_cs_deactivate(reg);

	return 0;
}

#ifndef CONFIG_DM_SPI

static struct kwspi_registers *spireg =
	(struct kwspi_registers *)MVEBU_SPI_BASE;

#ifdef CONFIG_KIRKWOOD
static u32 cs_spi_mpp_back[2];
#endif

struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
				unsigned int max_hz, unsigned int mode)
{
	struct spi_slave *slave;
	u32 data;
#ifdef CONFIG_KIRKWOOD
	static const u32 kwspi_mpp_config[2][2] = {
		{ MPP0_SPI_SCn, 0 }, /* if cs == 0 */
		{ MPP7_SPI_SCn, 0 } /* if cs != 0 */
	};
#endif

	if (!spi_cs_is_valid(bus, cs))
		return NULL;

	slave = spi_alloc_slave_base(bus, cs);
	if (!slave)
		return NULL;

	writel(KWSPI_SMEMRDY, &spireg->ctrl);

	/* calculate spi clock prescaller using max_hz */
	data = ((CONFIG_SYS_TCLK / 2) / max_hz) + 0x10;
	data = data < KWSPI_CLKPRESCL_MIN ? KWSPI_CLKPRESCL_MIN : data;
	data = data > KWSPI_CLKPRESCL_MASK ? KWSPI_CLKPRESCL_MASK : data;

	/* program spi clock prescaller using max_hz */
	writel(KWSPI_ADRLEN_3BYTE | data, &spireg->cfg);
	debug("data = 0x%08x\n", data);

	writel(KWSPI_SMEMRDIRQ, &spireg->irq_cause);
	writel(KWSPI_IRQMASK, &spireg->irq_mask);

#ifdef CONFIG_KIRKWOOD
	/* program mpp registers to select  SPI_CSn */
	kirkwood_mpp_conf(kwspi_mpp_config[cs ? 1 : 0], cs_spi_mpp_back);
#endif

	return slave;
}

void spi_free_slave(struct spi_slave *slave)
{
#ifdef CONFIG_KIRKWOOD
	kirkwood_mpp_conf(cs_spi_mpp_back, NULL);
#endif
	free(slave);
}

#if defined(CONFIG_SYS_KW_SPI_MPP)
u32 spi_mpp_backup[4];
#endif

__attribute__((weak)) int board_spi_claim_bus(struct spi_slave *slave)
{
	return 0;
}

int spi_claim_bus(struct spi_slave *slave)
{
#if defined(CONFIG_SYS_KW_SPI_MPP)
	u32 config;
	u32 spi_mpp_config[4];

	config = CONFIG_SYS_KW_SPI_MPP;

	if (config & MOSI_MPP6)
		spi_mpp_config[0] = MPP6_SPI_MOSI;
	else
		spi_mpp_config[0] = MPP1_SPI_MOSI;

	if (config & SCK_MPP10)
		spi_mpp_config[1] = MPP10_SPI_SCK;
	else
		spi_mpp_config[1] = MPP2_SPI_SCK;

	if (config & MISO_MPP11)
		spi_mpp_config[2] = MPP11_SPI_MISO;
	else
		spi_mpp_config[2] = MPP3_SPI_MISO;

	spi_mpp_config[3] = 0;
	spi_mpp_backup[3] = 0;

	/* set new spi mpp and save current mpp config */
	kirkwood_mpp_conf(spi_mpp_config, spi_mpp_backup);
#endif

	return board_spi_claim_bus(slave);
}

__attribute__((weak)) void board_spi_release_bus(struct spi_slave *slave)
{
}

void spi_release_bus(struct spi_slave *slave)
{
#if defined(CONFIG_SYS_KW_SPI_MPP)
	kirkwood_mpp_conf(spi_mpp_backup, NULL);
#endif

	board_spi_release_bus(slave);
}

#ifndef CONFIG_SPI_CS_IS_VALID
/*
 * you can define this function board specific
 * define above CONFIG in board specific config file and
 * provide the function in board specific src file
 */
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
{
	return bus == 0 && (cs == 0 || cs == 1);
}
#endif

void spi_init(void)
{
}

void spi_cs_activate(struct spi_slave *slave)
{
	_spi_cs_activate(spireg);
}

void spi_cs_deactivate(struct spi_slave *slave)
{
	_spi_cs_deactivate(spireg);
}

int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
	     const void *dout, void *din, unsigned long flags)
{
	return _spi_xfer(spireg, bitlen, dout, din, flags);
}

#else

/* Here now the DM part */

struct mvebu_spi_dev {
	bool			is_errata_50mhz_ac;
};

struct mvebu_spi_platdata {
	struct kwspi_registers *spireg;
};

struct mvebu_spi_priv {
	struct kwspi_registers *spireg;
};

static int mvebu_spi_set_speed(struct udevice *bus, uint hz)
{
	struct mvebu_spi_platdata *plat = dev_get_platdata(bus);
	struct kwspi_registers *reg = plat->spireg;
	u32 data;

	/* calculate spi clock prescaller using max_hz */
	data = ((CONFIG_SYS_TCLK / 2) / hz) + 0x10;
	data = data < KWSPI_CLKPRESCL_MIN ? KWSPI_CLKPRESCL_MIN : data;
	data = data > KWSPI_CLKPRESCL_MASK ? KWSPI_CLKPRESCL_MASK : data;

	/* program spi clock prescaler using max_hz */
	writel(KWSPI_ADRLEN_3BYTE | data, &reg->cfg);
	debug("data = 0x%08x\n", data);

	return 0;
}

static void mvebu_spi_50mhz_ac_timing_erratum(struct udevice *bus, uint mode)
{
	struct mvebu_spi_platdata *plat = dev_get_platdata(bus);
	struct kwspi_registers *reg = plat->spireg;
	u32 data;

	/*
	 * Erratum description: (Erratum NO. FE-9144572) The device
	 * SPI interface supports frequencies of up to 50 MHz.
	 * However, due to this erratum, when the device core clock is
	 * 250 MHz and the SPI interfaces is configured for 50MHz SPI
	 * clock and CPOL=CPHA=1 there might occur data corruption on
	 * reads from the SPI device.
	 * Erratum Workaround:
	 * Work in one of the following configurations:
	 * 1. Set CPOL=CPHA=0 in "SPI Interface Configuration
	 * Register".
	 * 2. Set TMISO_SAMPLE value to 0x2 in "SPI Timing Parameters 1
	 * Register" before setting the interface.
	 */
	data = readl(&reg->timing1);
	data &= ~KW_SPI_TMISO_SAMPLE_MASK;

	if (CONFIG_SYS_TCLK == 250000000 &&
	    mode & SPI_CPOL &&
	    mode & SPI_CPHA)
		data |= KW_SPI_TMISO_SAMPLE_2;
	else
		data |= KW_SPI_TMISO_SAMPLE_1;

	writel(data, &reg->timing1);
}

static int mvebu_spi_set_mode(struct udevice *bus, uint mode)
{
	struct mvebu_spi_platdata *plat = dev_get_platdata(bus);
	struct kwspi_registers *reg = plat->spireg;
	const struct mvebu_spi_dev *drvdata;
	u32 data = readl(&reg->cfg);

	data &= ~(KWSPI_CPHA | KWSPI_CPOL | KWSPI_RXLSBF | KWSPI_TXLSBF);

	if (mode & SPI_CPHA)
		data |= KWSPI_CPHA;
	if (mode & SPI_CPOL)
		data |= KWSPI_CPOL;
	if (mode & SPI_LSB_FIRST)
		data |= (KWSPI_RXLSBF | KWSPI_TXLSBF);

	writel(data, &reg->cfg);

	drvdata = (struct mvebu_spi_dev *)dev_get_driver_data(bus);
	if (drvdata->is_errata_50mhz_ac)
		mvebu_spi_50mhz_ac_timing_erratum(bus, mode);

	return 0;
}

static int mvebu_spi_xfer(struct udevice *dev, unsigned int bitlen,
			  const void *dout, void *din, unsigned long flags)
{
	struct udevice *bus = dev->parent;
	struct mvebu_spi_platdata *plat = dev_get_platdata(bus);

	return _spi_xfer(plat->spireg, bitlen, dout, din, flags);
}

static int mvebu_spi_claim_bus(struct udevice *dev)
{
	struct udevice *bus = dev->parent;
	struct mvebu_spi_platdata *plat = dev_get_platdata(bus);

	/* Configure the chip-select in the CTRL register */
	clrsetbits_le32(&plat->spireg->ctrl,
			KWSPI_CS_MASK << KWSPI_CS_SHIFT,
			spi_chip_select(dev) << KWSPI_CS_SHIFT);

	return 0;
}

static int mvebu_spi_probe(struct udevice *bus)
{
	struct mvebu_spi_platdata *plat = dev_get_platdata(bus);
	struct kwspi_registers *reg = plat->spireg;

	writel(KWSPI_SMEMRDY, &reg->ctrl);
	writel(KWSPI_SMEMRDIRQ, &reg->irq_cause);
	writel(KWSPI_IRQMASK, &reg->irq_mask);

	return 0;
}

static int mvebu_spi_ofdata_to_platdata(struct udevice *bus)
{
	struct mvebu_spi_platdata *plat = dev_get_platdata(bus);

	plat->spireg = (struct kwspi_registers *)devfdt_get_addr(bus);

	return 0;
}

static const struct dm_spi_ops mvebu_spi_ops = {
	.claim_bus	= mvebu_spi_claim_bus,
	.xfer		= mvebu_spi_xfer,
	.set_speed	= mvebu_spi_set_speed,
	.set_mode	= mvebu_spi_set_mode,
	/*
	 * cs_info is not needed, since we require all chip selects to be
	 * in the device tree explicitly
	 */
};

static const struct mvebu_spi_dev armada_xp_spi_dev_data = {
	.is_errata_50mhz_ac = false,
};

static const struct mvebu_spi_dev armada_375_spi_dev_data = {
	.is_errata_50mhz_ac = false,
};

static const struct mvebu_spi_dev armada_380_spi_dev_data = {
	.is_errata_50mhz_ac = true,
};

static const struct udevice_id mvebu_spi_ids[] = {
	{
		.compatible = "marvell,armada-375-spi",
		.data = (ulong)&armada_375_spi_dev_data
	},
	{
		.compatible = "marvell,armada-380-spi",
		.data = (ulong)&armada_380_spi_dev_data
	},
	{
		.compatible = "marvell,armada-xp-spi",
		.data = (ulong)&armada_xp_spi_dev_data
	},
	{ }
};

U_BOOT_DRIVER(mvebu_spi) = {
	.name = "mvebu_spi",
	.id = UCLASS_SPI,
	.of_match = mvebu_spi_ids,
	.ops = &mvebu_spi_ops,
	.ofdata_to_platdata = mvebu_spi_ofdata_to_platdata,
	.platdata_auto_alloc_size = sizeof(struct mvebu_spi_platdata),
	.priv_auto_alloc_size = sizeof(struct mvebu_spi_priv),
	.probe = mvebu_spi_probe,
};
#endif