blob: f09e138bb8c57c0c078c9e2deee725e8b5c89883 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
|
#
# System reset devices
#
menu "System reset device drivers"
config SYSRESET
bool "Enable support for system reset drivers"
depends on DM
help
Enable system reset drivers which can be used to reset the CPU or
board. Each driver can provide a reset method which will be called
to effect a reset. The uclass will try all available drivers when
reset_walk() is called.
config SPL_SYSRESET
bool "Enable support for system reset drivers in SPL mode"
depends on SYSRESET && SPL_DM
help
Enable system reset drivers which can be used to reset the CPU or
board. Each driver can provide a reset method which will be called
to effect a reset. The uclass will try all available drivers when
reset_walk() is called.
config TPL_SYSRESET
bool "Enable support for system reset drivers in TPL mode"
depends on SYSRESET && TPL_DM
help
Enable system reset drivers which can be used to reset the CPU or
board. Each driver can provide a reset method which will be called
to effect a reset. The uclass will try all available drivers when
reset_walk() is called.
if SYSRESET
if CMD_POWEROFF
config SYSRESET_CMD_POWEROFF
bool "sysreset implementation of the poweroff command"
help
This should be selected by the appropriate PMIC driver if
the poweroff command is enabled.
endif
config SYSRESET_GPIO
bool "Enable support for GPIO reset driver"
select DM_GPIO
help
Reset support via GPIO pin connected reset logic. This is used for
example on Microblaze where reset logic can be controlled via GPIO
pin which triggers cpu reset.
config SYSRESET_MICROBLAZE
bool "Enable support for Microblaze soft reset"
depends on MICROBLAZE
help
This is soft reset on Microblaze which does jump to 0x0 address.
config SYSRESET_PSCI
bool "Enable support for PSCI System Reset"
depends on ARM_PSCI_FW
select SPL_ARM_PSCI_FW if SPL
help
Enable PSCI SYSTEM_RESET function call. To use this, PSCI firmware
must be running on your system.
config SYSRESET_SOCFPGA
bool "Enable support for Intel SOCFPGA family"
depends on ARCH_SOCFPGA && (TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10)
help
This enables the system reset driver support for Intel SOCFPGA SoCs
(Cyclone 5, Arria 5 and Arria 10).
config SYSRESET_SOCFPGA_S10
bool "Enable support for Intel SOCFPGA Stratix 10"
depends on ARCH_SOCFPGA && TARGET_SOCFPGA_STRATIX10
help
This enables the system reset driver support for Intel SOCFPGA
Stratix SoCs.
config SYSRESET_TI_SCI
bool "TI System Control Interface (TI SCI) system reset driver"
depends on TI_SCI_PROTOCOL
help
This enables the system reset driver support over TI System Control
Interface available on some new TI's SoCs.
endif
config SYSRESET_SYSCON
bool "Enable support for mfd syscon reboot driver"
select REGMAP
select SYSCON
help
Reboot support for generic SYSCON mapped register reset.
config SYSRESET_WATCHDOG
bool "Enable support for watchdog reboot driver"
select WDT
help
Reboot support for generic watchdog reset.
config SYSRESET_X86
bool "Enable support for x86 processor reboot driver"
depends on X86
help
Reboot support for generic x86 processor reset.
config SYSRESET_SPL_X86
bool "Enable support for x86 processor reboot driver in SPL"
depends on X86
help
Reboot support for generic x86 processor reset in SPL.
config SYSRESET_TPL_X86
bool "Enable support for x86 processor reboot driver in TPL"
depends on X86
help
Reboot support for generic x86 processor reset in TPL.
config SYSRESET_MPC83XX
bool "Enable support MPC83xx SoC family reboot driver"
help
Reboot support for NXP MPC83xx SoCs.
endmenu
|
