1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
|
menuconfig USB
bool "USB support"
---help---
Universal Serial Bus (USB) is a specification for a serial bus
subsystem which offers higher speeds and more features than the
traditional PC serial port. The bus supplies power to peripherals
and allows for hot swapping. Up to 127 USB peripherals can be
connected to a single USB host in a tree structure.
The USB host is the root of the tree, the peripherals are the
leaves and the inner nodes are special USB devices called hubs.
Most PCs now have USB host ports, used to connect peripherals
such as scanners, keyboards, mice, modems, cameras, disks,
flash memory, network links, and printers to the PC.
Say Y here if your device has an USB port, either host, peripheral or
dual-role.
For an USB host port, you then need to say Y to at least one of the
Host Controller Driver (HCD) options below. Choose a USB 1.1
controller, such as "UHCI HCD support" or "OHCI HCD support",
and "EHCI HCD (USB 2.0) support" except for older systems that
do not have USB 2.0 support. It doesn't normally hurt to select
them all if you are not certain.
If your system has a device-side USB port, used in the peripheral
side of the USB protocol, see the "USB Gadget" framework instead.
After choosing your HCD, then select drivers for the USB peripherals
you'll be using. You may want to check out the information provided
in <file:Documentation/usb/> and especially the links given in
<file:Documentation/usb/usb-help.txt>.
if USB
config DM_USB
bool "Enable driver model for USB"
depends on USB && DM
help
Enable driver model for USB. The USB interface is then implemented
by the USB uclass. Multiple USB controllers of different types
(XHCI, EHCI) can be attached and used. The 'usb' command works as
normal. OCHI is not supported at present.
Much of the code is shared but with this option enabled the USB
uclass takes care of device enumeration. USB devices can be
declared with the U_BOOT_USB_DEVICE() macro and will be
automatically probed when found on the bus.
source "drivers/usb/host/Kconfig"
source "drivers/usb/dwc3/Kconfig"
source "drivers/usb/musb/Kconfig"
source "drivers/usb/musb-new/Kconfig"
source "drivers/usb/emul/Kconfig"
source "drivers/usb/phy/Kconfig"
source "drivers/usb/ulpi/Kconfig"
comment "USB peripherals"
config USB_STORAGE
bool "USB Mass Storage support"
---help---
Say Y here if you want to connect USB mass storage devices to your
board's USB port.
config USB_KEYBOARD
bool "USB Keyboard support"
---help---
Say Y here if you want to use a USB keyboard for U-Boot command line
input.
if USB_KEYBOARD
choice
prompt "USB keyboard polling"
default SYS_USB_EVENT_POLL
---help---
Enable a polling mechanism for USB keyboard.
config SYS_USB_EVENT_POLL
bool "Interrupt polling"
config SYS_USB_EVENT_POLL_VIA_INT_QUEUE
bool "Poll via interrupt queue"
config SYS_USB_EVENT_POLL_VIA_CONTROL_EP
bool "Poll via control EP"
endchoice
endif
source "drivers/usb/gadget/Kconfig"
source "drivers/usb/eth/Kconfig"
endif
|
