1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
|
/*
* Mentor USB OTG Core functionality common for both Host and Device
* functionality.
*
* Copyright (c) 2008 Texas Instruments
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*
* Author: Thomas Abraham t-abraham@ti.com, Texas Instruments
*/
#include <common.h>
#include "musb_core.h"
struct musb_regs *musbr;
/*
* program the mentor core to start (enable interrupts, dma, etc.)
*/
void musb_start(void)
{
#if defined(CONFIG_MUSB_HCD)
u8 devctl;
u8 busctl;
#endif
/* disable all interrupts */
writew(0, &musbr->intrtxe);
writew(0, &musbr->intrrxe);
writeb(0, &musbr->intrusbe);
writeb(0, &musbr->testmode);
/* put into basic highspeed mode and start session */
writeb(MUSB_POWER_HSENAB, &musbr->power);
#if defined(CONFIG_MUSB_HCD)
/* Program PHY to use EXT VBUS if required */
if (musb_cfg.extvbus == 1) {
busctl = musb_read_ulpi_buscontrol(musbr);
musb_write_ulpi_buscontrol(musbr, busctl | ULPI_USE_EXTVBUS);
}
devctl = readb(&musbr->devctl);
writeb(devctl | MUSB_DEVCTL_SESSION, &musbr->devctl);
#endif
}
#ifdef MUSB_NO_DYNAMIC_FIFO
# define config_fifo(dir, idx, addr)
#else
# define config_fifo(dir, idx, addr) \
do { \
writeb(idx, &musbr->dir##fifosz); \
writew(fifoaddr >> 3, &musbr->dir##fifoadd); \
} while (0)
#endif
/*
* This function configures the endpoint configuration. The musb hcd or musb
* device implementation can use this function to configure the endpoints
* and set the FIFO sizes. Note: The summation of FIFO sizes of all endpoints
* should not be more than the available FIFO size.
*
* epinfo - Pointer to EP configuration table
* cnt - Number of entries in the EP conf table.
*/
void musb_configure_ep(struct musb_epinfo *epinfo, u8 cnt)
{
u16 csr;
u16 fifoaddr = 64; /* First 64 bytes of FIFO reserved for EP0 */
u32 fifosize;
u8 idx;
while (cnt--) {
/* prepare fifosize to write to register */
fifosize = epinfo->epsize >> 3;
idx = ffs(fifosize) - 1;
writeb(epinfo->epnum, &musbr->index);
if (epinfo->epdir) {
/* Configure fifo size and fifo base address */
config_fifo(tx, idx, fifoaddr);
csr = readw(&musbr->txcsr);
#if defined(CONFIG_MUSB_HCD)
/* clear the data toggle bit */
writew(csr | MUSB_TXCSR_CLRDATATOG, &musbr->txcsr);
#endif
/* Flush fifo if required */
if (csr & MUSB_TXCSR_TXPKTRDY)
writew(csr | MUSB_TXCSR_FLUSHFIFO,
&musbr->txcsr);
} else {
/* Configure fifo size and fifo base address */
config_fifo(rx, idx, fifoaddr);
csr = readw(&musbr->rxcsr);
#if defined(CONFIG_MUSB_HCD)
/* clear the data toggle bit */
writew(csr | MUSB_RXCSR_CLRDATATOG, &musbr->rxcsr);
#endif
/* Flush fifo if required */
if (csr & MUSB_RXCSR_RXPKTRDY)
writew(csr | MUSB_RXCSR_FLUSHFIFO,
&musbr->rxcsr);
}
fifoaddr += epinfo->epsize;
epinfo++;
}
}
/*
* This function writes data to endpoint fifo
*
* ep - endpoint number
* length - number of bytes to write to FIFO
* fifo_data - Pointer to data buffer that contains the data to write
*/
__attribute__((weak))
void write_fifo(u8 ep, u32 length, void *fifo_data)
{
u8 *data = (u8 *)fifo_data;
/* select the endpoint index */
writeb(ep, &musbr->index);
/* write the data to the fifo */
while (length--)
writeb(*data++, &musbr->fifox[ep]);
}
/*
* This function reads data from endpoint fifo
*
* ep - endpoint number
* length - number of bytes to read from FIFO
* fifo_data - pointer to data buffer into which data is read
*/
__attribute__((weak))
void read_fifo(u8 ep, u32 length, void *fifo_data)
{
u8 *data = (u8 *)fifo_data;
/* select the endpoint index */
writeb(ep, &musbr->index);
/* read the data to the fifo */
while (length--)
*data++ = readb(&musbr->fifox[ep]);
}
|
