blob: 446596ed912bbed5aa01a92735256f8861e25988 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
|
/*
* Copyright (C) 2014 Stefan Roese <sr@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _CONFIG_DB_88F6820_AMC_H
#define _CONFIG_DB_88F6820_AMC_H
/*
* High Level Configuration Options (easy to change)
*/
#define CONFIG_DISPLAY_BOARDINFO_LATE
/*
* TEXT_BASE needs to be below 16MiB, since this area is scrubbed
* for DDR ECC byte filling in the SPL before loading the main
* U-Boot into it.
*/
#define CONFIG_SYS_TEXT_BASE 0x00800000
#define CONFIG_SYS_TCLK 200000000 /* 200MHz */
/*
* Commands configuration
*/
#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
#define CONFIG_CMD_ENV
#define CONFIG_CMD_PCI
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MVTWSI
#define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE
#define CONFIG_SYS_I2C_SLAVE 0x0
#define CONFIG_SYS_I2C_SPEED 100000
/* SPI NOR flash default params, used by sf commands */
#define CONFIG_SF_DEFAULT_BUS 1
#define CONFIG_SF_DEFAULT_SPEED 1000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3
/* Partition support */
#define CONFIG_DOS_PARTITION
#define CONFIG_EFI_PARTITION
/* Additional FS support/configuration */
#define CONFIG_SUPPORT_VFAT
/* USB/EHCI configuration */
#define CONFIG_EHCI_IS_TDI
/* Environment in SPI NOR flash */
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_BUS 1
#define CONFIG_ENV_OFFSET (1 << 20) /* 1MiB in */
#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */
#define CONFIG_ENV_SECT_SIZE (256 << 10) /* 256KiB sectors */
#define CONFIG_PHY_MARVELL /* there is a marvell phy */
#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */
/* PCIe support */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_PCI
#define CONFIG_PCI_MVEBU
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#endif
/* NAND */
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_ALT_MEMTEST
/* Keep device tree and initrd in lower memory so the kernel can access them */
#define CONFIG_EXTRA_ENV_SETTINGS \
"fdt_high=0x10000000\0" \
"initrd_high=0x10000000\0"
/* SPL */
/*
* Select the boot device here
*
* Currently supported are:
* SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash
*
* MMC is not populated on this board.
* NAND support may be added in the future.
*/
#define SPL_BOOT_SPI_NOR_FLASH 1
#define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SPI_NOR_FLASH
/* Defines for SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_SIZE (140 << 10)
#define CONFIG_SPL_TEXT_BASE 0x40000030
#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030)
#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)
#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH
/* SPL related SPI defines */
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x24000
#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS
#endif
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros
*/
#include "mv-common.h"
#undef CONFIG_SYS_MAXARGS
#define CONFIG_SYS_MAXARGS 96
#endif /* _CONFIG_DB_88F6820_AMC_H */
|
