blob: 212dee7f28c548f3500d436f6f5b3c85fc1d32f7 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
|
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2014 Gateworks Corporation
* Author: Tim Harvey <tharvey@gateworks.com>
*/
#ifndef __IMX6_SPL_CONFIG_H
#define __IMX6_SPL_CONFIG_H
#ifdef CONFIG_SPL
/*
* see Figure 8-3 in IMX6DQ/IMX6SDL Reference manuals:
* - IMX6SDL OCRAM (IRAM) is from 0x00907000 to 0x0091FFFF
* - IMX6DQ has 2x IRAM of IMX6SDL but we intend to support IMX6SDL as well
* - BOOT ROM stack is at 0x0091FFB8
* - if icache/dcache is enabled (eFuse/strapping controlled) then the
* IMX BOOT ROM will setup MMU table at 0x00918000, therefore we need to
* fit between 0x00907000 and 0x00918000.
* - Additionally the BOOT ROM loads what they consider the firmware image
* which consists of a 4K header in front of us that contains the IVT, DCD
* and some padding thus 'our' max size is really 0x00908000 - 0x00918000
* or 64KB
*/
#define CONFIG_SPL_MAX_SIZE 0x10000
#define CONFIG_SPL_STACK 0x0091FFB8
/*
* Pad SPL to 68KB (4KB header + 64KB max size). This allows to write the
* SPL/U-Boot combination generated with u-boot-with-spl.imx directly to a
* boot media (given that boot media specific offset is configured properly).
*/
#define CONFIG_SPL_PAD_TO 0x11000
/* MMC support */
#if defined(CONFIG_SPL_MMC_SUPPORT)
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SYS_MONITOR_LEN 409600 /* 400 KB */
#endif
/* SATA support */
#if defined(CONFIG_SPL_SATA_SUPPORT)
#define CONFIG_SPL_SATA_BOOT_DEVICE 0
#define CONFIG_SYS_SATA_FAT_BOOT_PARTITION 1
#endif
/* Define the payload for FAT/EXT support */
#if defined(CONFIG_SPL_FS_FAT) || defined(CONFIG_SPL_FS_EXT4)
# ifdef CONFIG_OF_CONTROL
# define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot-dtb.img"
# else
# define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
# endif
#endif
#if defined(CONFIG_MX6SX) || defined(CONFIG_MX6SL) || \
defined(CONFIG_MX6UL) || defined(CONFIG_MX6ULL)
#define CONFIG_SPL_BSS_START_ADDR 0x88200000
#define CONFIG_SPL_BSS_MAX_SIZE 0x100000 /* 1 MB */
#define CONFIG_SYS_SPL_MALLOC_START 0x88300000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */
#else
#define CONFIG_SPL_BSS_START_ADDR 0x18200000
#define CONFIG_SPL_BSS_MAX_SIZE 0x100000 /* 1 MB */
#define CONFIG_SYS_SPL_MALLOC_START 0x18300000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */
#endif
#endif
#endif
|
