blob: 639d87a4e5787ed963f118fdb09259a235a653dc (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
|
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Configuration header file for K3 J721E EVM
*
* Copyright (C) 2018-2019 Texas Instruments Incorporated - http://www.ti.com/
* Lokesh Vutla <lokeshvutla@ti.com>
*/
#ifndef __CONFIG_J721E_EVM_H
#define __CONFIG_J721E_EVM_H
#include <linux/sizes.h>
#include <config_distro_bootcmd.h>
#include <environment/ti/mmc.h>
#include <environment/ti/k3_rproc.h>
#include <environment/ti/ufs.h>
#define CONFIG_ENV_SIZE (128 << 10)
/* DDR Configuration */
#define CONFIG_SYS_SDRAM_BASE1 0x880000000
/* SPL Loader Configuration */
#ifdef CONFIG_TARGET_J721E_A72_EVM
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SPL_TEXT_BASE + \
CONFIG_SYS_K3_NON_SECURE_MSRAM_SIZE)
#else
/*
* Maximum size in memory allocated to the SPL BSS. Keep it as tight as
* possible (to allow the build to go through), as this directly affects
* our memory footprint. The less we use for BSS the more we have available
* for everything else.
*/
#define CONFIG_SPL_BSS_MAX_SIZE 0xA000
/*
* Link BSS to be within SPL in a dedicated region located near the top of
* the MCU SRAM, this way making it available also before relocation. Note
* that we are not using the actual top of the MCU SRAM as there is a memory
* location filled in by the boot ROM that we want to read out without any
* interference from the C context.
*/
#define CONFIG_SPL_BSS_START_ADDR (CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX -\
CONFIG_SPL_BSS_MAX_SIZE)
/* Set the stack right below the SPL BSS section */
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SPL_BSS_START_ADDR
/* Configure R5 SPL post-relocation malloc pool in DDR */
#define CONFIG_SYS_SPL_MALLOC_START 0x84000000
#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_16M
#endif
#ifdef CONFIG_SYS_K3_SPL_ATF
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "tispl.bin"
#endif
#define CONFIG_SPL_MAX_SIZE CONFIG_SYS_K3_MAX_DOWNLODABLE_IMAGE_SIZE
#define CONFIG_SYS_BOOTM_LEN SZ_64M
#define CONFIG_CQSPI_REF_CLK 133333333
/* HyperFlash related configuration */
#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1
/* U-Boot general configuration */
#define EXTRA_ENV_J721E_BOARD_SETTINGS \
"default_device_tree=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
"findfdt=setenv fdtfile ${default_device_tree}\0" \
"loadaddr=0x80080000\0" \
"fdtaddr=0x82000000\0" \
"overlayaddr=0x83000000\0" \
"name_kern=Image\0" \
"console=ttyS2,115200n8\0" \
"args_all=setenv optargs earlycon=ns16550a,mmio32,0x02800000\0" \
"run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0"
/* U-Boot MMC-specific configuration */
#define EXTRA_ENV_J721E_BOARD_SETTINGS_MMC \
"boot=mmc\0" \
"mmcdev=1\0" \
"bootpart=1:2\0" \
"bootdir=/boot\0" \
"rd_spec=-\0" \
"init_mmc=run args_all args_mmc\0" \
"get_fdt_mmc=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
"get_overlay_mmc=" \
"fdt address ${fdtaddr};" \
"fdt resize 0x100000;" \
"for overlay in $name_overlays;" \
"do;" \
"load mmc ${bootpart} ${overlayaddr} ${bootdir}/${overlay} && " \
"fdt apply ${overlayaddr};" \
"done;\0" \
"get_kern_mmc=load mmc ${bootpart} ${loadaddr} " \
"${bootdir}/${name_kern}\0"
#ifdef DEFAULT_RPROCS
#undef DEFAULT_RPROCS
#endif
#define DEFAULT_RPROCS "" \
"3 /lib/firmware/j7-main-r5f0_1-fw " \
"4 /lib/firmware/j7-main-r5f1_0-fw " \
"6 /lib/firmware/j7-c66_0-fw " \
"7 /lib/firmware/j7-c66_1-fw " \
"8 /lib/firmware/j7-c71_0-fw "
/* Incorporate settings into the U-Boot environment */
#define CONFIG_EXTRA_ENV_SETTINGS \
DEFAULT_MMC_TI_ARGS \
EXTRA_ENV_J721E_BOARD_SETTINGS \
EXTRA_ENV_J721E_BOARD_SETTINGS_MMC \
EXTRA_ENV_RPROC_SETTINGS \
DEFAULT_UFS_TI_ARGS
/* Now for the remaining common defines */
#include <configs/ti_armv7_common.h>
#endif /* __CONFIG_J721E_EVM_H */
|
