1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
|
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2010
* Ilko Iliev <iliev@ronetix.at>
* Asen Dimov <dimov@ronetix.at>
* Ronetix GmbH <www.ronetix.at>
*
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
* Configuation settings for the PM9G45 board.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_SKIP_LOWLEVEL_INIT
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
/* SDRAM */
#define CONFIG_SYS_SDRAM_BASE 0x70000000
#define CONFIG_SYS_SDRAM_SIZE 0x08000000
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
/* NAND flash */
#ifdef CONFIG_CMD_NAND
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
#define CONFIG_SYS_NAND_DBW_8
/* our ALE is AD21 */
#define CONFIG_SYS_NAND_MASK_ALE BIT(21)
/* our CLE is AD22 */
#define CONFIG_SYS_NAND_MASK_CLE BIT(22)
#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PD3
#define CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
#endif
/* Ethernet */
#define CONFIG_RESET_PHY_R
#define CONFIG_AT91_WANTS_COMMON_PHY
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END 0x23e00000
#ifdef CONFIG_NAND_BOOT
/* bootstrap + u-boot + env in nandflash */
#define CONFIG_BOOTCOMMAND \
"nand read 0x70000000 0x200000 0x300000;" \
"bootm 0x70000000"
#elif CONFIG_SD_BOOT
/* bootstrap + u-boot + env + linux in mmc */
#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x71000000 dtb; " \
"fatload mmc 0:1 0x72000000 zImage; " \
"bootz 0x72000000 - 0x71000000"
#endif
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + \
128 * 1024, 0x1000)
/* Defines for SPL */
#define CONFIG_SPL_MAX_SIZE 0x010000
#define CONFIG_SPL_STACK 0x310000
#define CONFIG_SYS_MONITOR_LEN 0x80000
#ifdef CONFIG_SD_BOOT
#define CONFIG_SPL_BSS_START_ADDR 0x70000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x00080000
#define CONFIG_SYS_SPL_MALLOC_START 0x70080000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#elif CONFIG_NAND_BOOT
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_ECC
#define CONFIG_SPL_NAND_SOFTECC
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCSIZE 256
#define CONFIG_SYS_NAND_ECCBYTES 3
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \
48, 49, 50, 51, 52, 53, 54, 55, \
56, 57, 58, 59, 60, 61, 62, 63, }
#endif
#define CONFIG_SPL_ATMEL_SIZE
#define CONFIG_SYS_MASTER_CLOCK 132096000
#define CONFIG_SYS_AT91_PLLA 0x20c73f03
#define CONFIG_SYS_MCKR 0x1301
#define CONFIG_SYS_MCKR_CSS 0x1302
#endif
|
