powerpc: remove MBX and MBX860T boards support

Enough time has passed since these boards were moved to Orphan. Remove.

 - Remove board/mbx8xx/*
 - Remove include/configs/{MBX.h,MBX860T.h}
 - Clean-up if defined(CONFIG_MBX)
 - Move the entries from boards.cfg to doc/README.scrapyard

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

23 files changed, 1 insertions, 2411 deletions

diff --git a/arch/powerpc/cpu/mpc8xx/cpu_init.c b/arch/powerpc/cpu/mpc8xx/cpu_init.c
index 53f873d1ab..69455c7be0 100644
--- a/arch/powerpc/cpu/mpc8xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc8xx/cpu_init.c
@@ -29,12 +29,10 @@ void cpm_load_patch (volatile immap_t * immr);
  */
 void cpu_init_f (volatile immap_t * immr)
 {
-#ifndef CONFIG_MBX
 	volatile memctl8xx_t *memctl = &immr->im_memctl;
 # ifdef CONFIG_SYS_PLPRCR
 	ulong mfmask;
 # endif
-#endif
 	ulong reg;
 
 	/* SYPCR - contains watchdog control (11-9) */
@@ -74,8 +72,6 @@ void cpu_init_f (volatile immap_t * immr)
 
 	immr->im_clkrstk.cark_plprcrk = KAPWR_KEY;
 
-#ifndef CONFIG_MBX		/* MBX board does things different */
-
 	/* If CONFIG_SYS_PLPRCR (set in the various *_config.h files) tries to
 	 * set the MF field, then just copy CONFIG_SYS_PLPRCR over car_plprcr,
 	 * otherwise OR in CONFIG_SYS_PLPRCR so we do not change the current MF
@@ -203,8 +199,6 @@ void cpu_init_f (volatile immap_t * immr)
 	memctl->memc_br7 = CONFIG_SYS_BR7_PRELIM;
 #endif
 
-#endif /* ! CONFIG_MBX */
-
 	/*
 	 * Reset CPM
 	 */
@@ -213,16 +207,6 @@ void cpu_init_f (volatile immap_t * immr)
 		__asm__ ("eieio");
 	} while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
 
-#ifdef CONFIG_MBX
-	/*
-	 * on the MBX, things are a little bit different:
-	 * - we need to read the VPD to get board information
-	 * - the plprcr is set up dynamically
-	 * - the memory controller is set up dynamically
-	 */
-	mbx_init ();
-#endif /* CONFIG_MBX */
-
 #ifdef CONFIG_RPXCLASSIC
 	rpxclassic_init ();
 #endif
diff --git a/arch/powerpc/cpu/mpc8xx/scc.c b/arch/powerpc/cpu/mpc8xx/scc.c
index 2ef77b4c14..94c9969e3f 100644
--- a/arch/powerpc/cpu/mpc8xx/scc.c
+++ b/arch/powerpc/cpu/mpc8xx/scc.c
@@ -492,10 +492,6 @@ static int scc_init (struct eth_device *dev, bd_t * bis)
 	immr->im_cpm.cp_pbdat &= ~0x00000010;
 #endif /* QS860T */
 
-#ifdef CONFIG_MBX
-	board_ether_init ();
-#endif
-
 #if defined(CONFIG_NETVIA)
 #if defined(PA_ENET_PDN)
 	immr->im_ioport.iop_papar &= ~PA_ENET_PDN;
diff --git a/arch/powerpc/cpu/mpc8xx/serial.c b/arch/powerpc/cpu/mpc8xx/serial.c
index 4e840498d7..cb48ed942f 100644
--- a/arch/powerpc/cpu/mpc8xx/serial.c
+++ b/arch/powerpc/cpu/mpc8xx/serial.c
@@ -225,10 +225,6 @@ static int smc_init (void)
 	up->smc_tstate = 0;
 #endif
 
-#if defined(CONFIG_MBX)
-	board_serial_init();
-#endif	/* CONFIG_MBX */
-
 	/* Set UART mode, 8 bit, no parity, one stop.
 	 * Enable receive and transmit.
 	 */
diff --git a/arch/powerpc/include/asm/immap_512x.h b/arch/powerpc/include/asm/immap_512x.h
index bed80aa933..6086a73ba9 100644
--- a/arch/powerpc/include/asm/immap_512x.h
+++ b/arch/powerpc/include/asm/immap_512x.h
@@ -59,7 +59,6 @@ typedef struct sysconf512x {
 	u8 res2[0x28];
 	law512x_t ddrlaw;	/* DDR Local Access Window */
 	u8 res3[0x18];
-	u32 mbxbar;		/* MBX Base Address */
 	u32 srambar;		/* SRAM Base Address */
 	u32 nfcbar;		/* NFC Base Address */
 	u8 res4[0x34];
diff --git a/board/mbx8xx/Makefile b/board/mbx8xx/Makefile
deleted file mode 100644
index 2074b6b904..0000000000
--- a/board/mbx8xx/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	= mbx8xx.o flash.o vpd.o pcmcia.o
diff --git a/board/mbx8xx/README b/board/mbx8xx/README
deleted file mode 100644
index c889fe9791..0000000000
--- a/board/mbx8xx/README
+++ /dev/null
@@ -1,68 +0,0 @@
-IMPORTANT NOTE - read before defining CONFIG_SYS_USE_OSCCLK in your board
-		 config file!!!
-
-
-WARNING: Wrong settings of this parameter have the potential to
-damage hardware by running the MBX's CPU at frequencies that exceed
-it's rating and/or overdriving the it's SPLL!
-
-
-Ramblings:
-1) Motorola offered 12 different variants of the MBX, 6 823s and 6 860s.
-2) Of these 12 variants, only 2 were entry level boards.
-3) I believe that the 2 entry level boards were the only ones that
-   used OSCM clocking. I can't be completely certain of this at this
-   point.
-4) Motorola never offered an MBX that ran faster than 50Mhz.
-5) The 10, non-entry level boards, ran at 40Mhz.
-6) The EXTCLK input has a minimum clock of 15Mhz for the 823/860.
-7) Motorola no longer sells MBXs.
-
-Based on this information, I can surmise that the default power-on
-reset clocking was one of the following three options.
-
-Multiplier       SPLL Options
-------------------------------------
-513              OSCM is SPLL input
-5                OSCM is SPLL input
-1                EXTCLK is SPLL input
-
-The forth option:
-
-5                EXTCLK is SPLL input
-
-is not possible on MBXs. This is because the minimum EXTCLK input
-frequency is 15Mhz. 5 * 15Mhz = 75 Mhz. There was no variant that ran
-above 50 Mhz.
-
-The board I have borrowed definitely uses a multiplier of 1 for
-EXTCLK and runs at 40Mhz. I even went so far as to put a scope on it.
-
-One of the two default OSCM modes are most likely what was used on
-the entry level boards to cheapen them by eliminating the external
-crystal oscillator.
-
-To add insult to injury, the stupid 860 PLPRCR register retains it's
-multiplication factor through hard resets. You can't clear it out
-because it is battery backed and once it is set wrong, it stays
-wrong. The only way to reset it, so that it takes on it's default
-multiplier is to disconnect all power including external, batteries,
-as well discharging caps on the board. This precludes the fact that
-your 860 may be quite DEAD by this time!
-
-If you don't setup the multiplication factor for boards that use the
-OSCM input, they won't run correctly, but at least they won't be
-dead.
-
-Addtionally, there is no good way to determine the clock input source
-from CPU register data. The only way to deal with this is either hard
-code it, determine the correct value with some rather NASTY timing
-loops, or try to grok it from external data sources. Motorola
-firmware opts for the NASTY timing loops, but needs to configure the
-serial ports to do so.
-
-
-You may have a legitimate need to define CONFIG_SYS_USE_OSCCLK if your
-MBX8xx board is using the OSCM clocking mode.
-
-You better know what you are doing here.
diff --git a/board/mbx8xx/csr.h b/board/mbx8xx/csr.h
deleted file mode 100644
index 937060973e..0000000000
--- a/board/mbx8xx/csr.h
+++ /dev/null
@@ -1,44 +0,0 @@
-#ifndef __csr_h
-#define __csr_h
-
-/*
- * (C) Copyright 2000
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * Control and Status Register definitions for the MBX
- *
- *--------------------------------------------------------------------
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/* bits for control register #1 / status register #1 */
-#define CSR1_ETEN       0x80    /* Ethernet Transceiver Enabled             */
-#define CSR1_ELEN       0x40    /* Ethernet XCVR in Internal Loopback       */
-#define CSR1_EAEN       0x20    /* Auto selection TP/AUI Enabled            */
-#define CSR1_TPEN       0x10    /* TP manually selected                     */
-#define CSR1_FDDIS      0x08    /* Full Duplex Mode disabled                */
-#define CSR1_FCTEN      0x04    /* Collision Testing of XCVR disabled       */
-#define CSR1_COM1EN     0x02    /* COM1 signals routed to RS232 Transceiver */
-#define CSR1_XCVRDIS    0x01    /* Onboard RS232 Transceiver Disabled       */
-
-/* bits for control register #2 */
-#define CR2_VDDSEL      0xC0    /* PCMCIA Supply Voltage                    */
-#define CR2_VPPSEL      0x30    /* PCMCIA Programming Voltage               */
-#define CR2_BRDFAIL     0x08    /* Board fail                               */
-#define CR2_SWS1        0x04    /* Software Status #2 LED                   */
-#define CR2_SWS2        0x02    /* Software Status #2 LED                   */
-#define CR2_QSPANRST    0x01    /* Reset QSPAN                              */
-
-/* bits for status register #2 */
-#define SR2_VDDSEL      0xC0    /* PCMCIA Supply Voltage                    */
-#define SR2_VPPSEL      0x30    /* PCMCIA Programming Voltage               */
-#define SR2_BATGD       0x08    /* Low Voltage indication for onboard bat   */
-#define SR2_NVBATGD     0x04    /* Low Voltage indication for NVRAM         */
-#define SR2_RDY         0x02    /* Flash programming status bit             */
-#define SR2_FT          0x01    /* Reserved for Factory test purposes       */
-
-#define MBX_CSR1 (*((uchar *)CONFIG_SYS_CSR_BASE))
-#define MBX_CSR2 (*((uchar *)CONFIG_SYS_CSR_BASE + 1))
-
-#endif /* __csr_h */
diff --git a/board/mbx8xx/dimm.h b/board/mbx8xx/dimm.h
deleted file mode 100644
index b40f112356..0000000000
--- a/board/mbx8xx/dimm.h
+++ /dev/null
@@ -1,98 +0,0 @@
-#ifndef __dimm_h
-#define __dimm_h
-
-/*
- * Module name: %M%
- * Description:
- * Serial Presence Detect Definitions Module
- * SCCS identification: %I%
- * Branch: %B%
- * Sequence: %S%
- * Date newest applied delta was created (MM/DD/YY): %G%
- * Time newest applied delta was created (HH:MM:SS): %U%
- * SCCS file name %F%
- * Fully qualified SCCS file name:
- * %P%
- * Copyright:
- * (C) COPYRIGHT MOTOROLA, INC. 1996
- * ALL RIGHTS RESERVED
- * Notes:
- * 1. All data was taken from an IBM application note titled
- * "Serial Presence Detect Definitions".
- * History:
- * Date Who
- *
- * 10/24/96 Rob Baxter
- * Initial release.
- *
- */
-
-/*
- * serial PD byte assignment address map (256 byte EEPROM)
- */
-typedef struct dimm
-{
-	uchar n_bytes; /* 00 number of bytes written/used */
-	uchar t_bytes; /* 01 total number of bytes in serial PD device */
-	uchar fmt; /* 02 fundamental memory type (FPM/EDO/SDRAM) */
-	uchar n_row; /* 03 number of rows */
-	uchar n_col; /* 04 number of columns */
-	uchar n_banks; /* 05 number of banks */
-	uchar data_w_lo; /* 06 data width */
-	uchar data_w_hi; /* 07 data width */
-	uchar ifl; /* 08 interface levels */
-	uchar a_ras; /* 09 RAS access */
-	uchar a_cas; /* 0A CAS access */
-	uchar ct; /* 0B configuration type (non-parity/parity/ECC) */
-	uchar refresh_rt; /* 0C refresh rate/type */
-	uchar p_dram_o; /* 0D primary DRAM organization */
-	uchar s_dram_o; /* 0E secondary DRAM organization (parity/ECC-checkbits) */
-	uchar reserved[17]; /* 0F reserved fields for future offerings */
-	uchar ss_info[32]; /* 20 superset information (may be used in the future) */
-	uchar m_info[64]; /* 40 manufacturer information (optional) */
-	uchar unused[128]; /* 80 unused storage locations */
-} dimm_t;
-
-/*
- * memory type definitions
- */
-#define DIMM_MT_FPM 1 /* standard FPM (fast page mode) DRAM */
-#define DIMM_MT_EDO 2 /* EDO (extended data out) */
-#define DIMM_MT_PN 3 /* pipelined nibble */
-#define DIMM_MT_SDRAM 4 /* SDRAM (synchronous DRAM) */
-
-/*
- * row addresses definitions
- */
-#define DIMM_RA_RDNDNT (1<<7) /* redundant addressing */
-#define DIMM_RA_MASK 0x7f /* number of row addresses mask */
-
-/*
- * module interface levels definitions
- */
-#define DIMM_IFL_TTL 0 /* TTL/5V tolerant */
-#define DIMM_IFL_LVTTL 1 /* LVTTL (not 5V tolerant) */
-#define DIMM_IFL_HSTL15 2 /* HSTL 1.5 */
-#define DIMM_IFL_SSTL33 3 /* SSTL 3.3 */
-#define DIMM_IFL_SSTL25 4 /* SSTL 2.5 */
-
-/*
- * DIMM configuration type definitions
- */
-#define DIMM_CT_NONE 0 /* none */
-#define DIMM_CT_PARITY 1 /* parity */
-#define DIMM_CT_ECC 2 /* ECC */
-
-/*
- * row addresses definitions
- */
-#define DIMM_RRT_SR (1<<7) /* self refresh flag */
-#define DIMM_RRT_MASK 0x7f /* refresh rate mask */
-#define DIMM_RRT_NRML 0x00 /* normal (15.625us) */
-#define DIMM_RRT_R_3_9 0x01 /* reduced .25x (3.9us) */
-#define DIMM_RRT_R_7_8 0x02 /* reduced .5x (7.8us) */
-#define DIMM_RRT_E_31_3 0x03 /* extended 2x (31.3us) */
-#define DIMM_RRT_E_62_5 0x04 /* extended 4x (62.5us) */
-#define DIMM_RRT_E_125 0x05 /* extended 8x (125us) */
-
-#endif /* __dimm_h */
diff --git a/board/mbx8xx/flash.c b/board/mbx8xx/flash.c
deleted file mode 100644
index fa07152cc8..0000000000
--- a/board/mbx8xx/flash.c
+++ /dev/null
@@ -1,392 +0,0 @@
-/*
- * (C) Copyright 2000
- * Marius Groeger <mgroeger@sysgo.de>
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * Flash Routines for AM290[48]0B devices
- *
- *--------------------------------------------------------------------
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-#include "vpd.h"
-
-flash_info_t	flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-
-static ulong flash_get_size (vu_long *addr, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
-    unsigned long size, totsize;
-    int i;
-    ulong addr;
-
-    /* Init: no FLASHes known */
-    for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
-	flash_info[i].flash_id = FLASH_UNKNOWN;
-    }
-
-    totsize = 0;
-    addr = 0xfc000000;
-    for(i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
-	size = flash_get_size((vu_long *)addr, &flash_info[i]);
-	if (flash_info[i].flash_id == FLASH_UNKNOWN)
-	  break;
-	totsize += size;
-	addr += size;
-    }
-
-    addr = 0xfe000000;
-    for(i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
-
-	size = flash_get_size((vu_long *)addr, &flash_info[i]);
-	if (flash_info[i].flash_id == FLASH_UNKNOWN)
-	  break;
-	totsize += size;
-	addr += size;
-    }
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
-    /* monitor protection ON by default */
-    flash_protect(FLAG_PROTECT_SET,
-		  CONFIG_SYS_MONITOR_BASE,
-		  CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
-		  &flash_info[0]);
-#endif
-
-    return (totsize);
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info  (flash_info_t *info)
-{
-    int i;
-
-    if (info->flash_id == FLASH_UNKNOWN) {
-	printf ("missing or unknown FLASH type\n");
-	return;
-    }
-
-    switch (info->flash_id >> 16) {
-    case 0x1:
-	printf ("AMD ");
-	break;
-    default:
-	printf ("Unknown Vendor ");
-	break;
-    }
-
-    switch (info->flash_id & FLASH_TYPEMASK) {
-    case AMD_ID_F040B:
-	printf ("AM29F040B (4 Mbit)\n");
-	break;
-    case AMD_ID_F080B:
-	printf ("AM29F080B (8 Mbit)\n");
-	break;
-    case AMD_ID_F016D:
-	printf ("AM29F016D (16 Mbit)\n");
-	break;
-    default:
-	printf ("Unknown Chip Type\n");
-	break;
-    }
-
-    printf ("  Size: %ld MB in %d Sectors\n",
-	    info->size >> 20, info->sector_count);
-
-    printf ("  Sector Start Addresses:");
-    for (i=0; i<info->sector_count; ++i) {
-	if ((i % 5) == 0)
-	  printf ("\n   ");
-	printf (" %08lX%s",
-		info->start[i],
-		info->protect[i] ? " (RO)" : "     "
-		);
-    }
-    printf ("\n");
-    return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size (vu_long *addr, flash_info_t *info)
-{
-    short i;
-    ulong vendor, devid;
-    ulong base = (ulong)addr;
-
-    /* Write auto select command: read Manufacturer ID */
-    addr[0x0555] = 0xAAAAAAAA;
-    addr[0x02AA] = 0x55555555;
-    addr[0x0555] = 0x90909090;
-
-    vendor = addr[0];
-    devid = addr[1] & 0xff;
-
-    /* only support AMD */
-    if (vendor != 0x01010101) {
-	return 0;
-    }
-
-    vendor &= 0xf;
-    devid &= 0xff;
-
-    if (devid == AMD_ID_F040B) {
-	info->flash_id     = vendor << 16 | devid;
-	info->sector_count = 8;
-	info->size         = info->sector_count * 0x10000;
-    }
-    else if (devid == AMD_ID_F080B) {
-	info->flash_id     = vendor << 16 | devid;
-	info->sector_count = 16;
-	info->size         = 4 * info->sector_count * 0x10000;
-    }
-    else if (devid == AMD_ID_F016D) {
-	info->flash_id     = vendor << 16 | devid;
-	info->sector_count = 32;
-	info->size         = 4 * info->sector_count * 0x10000;
-    }
-    else {
-	printf ("## Unknown Flash Type: %08lx\n", devid);
-	return 0;
-    }
-
-    /* check for protected sectors */
-    for (i = 0; i < info->sector_count; i++) {
-	/* sector base address */
-	info->start[i] = base + i * (info->size / info->sector_count);
-	/* read sector protection at sector address, (A7 .. A0) = 0x02 */
-	/* D0 = 1 if protected */
-	addr = (volatile unsigned long *)(info->start[i]);
-	info->protect[i] = addr[2] & 1;
-    }
-
-    /*
-     * Prevent writes to uninitialized FLASH.
-     */
-    if (info->flash_id != FLASH_UNKNOWN) {
-	addr = (vu_long *)info->start[0];
-	addr[0] = 0xF0;	/* reset bank */
-    }
-
-    return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int	flash_erase (flash_info_t *info, int s_first, int s_last)
-{
-    vu_long *addr = (vu_long*)(info->start[0]);
-    int flag, prot, sect, l_sect;
-    ulong start, now, last;
-
-    if ((s_first < 0) || (s_first > s_last)) {
-	if (info->flash_id == FLASH_UNKNOWN) {
-	    printf ("- missing\n");
-	} else {
-	    printf ("- no sectors to erase\n");
-	}
-	return 1;
-    }
-
-    prot = 0;
-    for (sect = s_first; sect <= s_last; sect++) {
-	if (info->protect[sect]) {
-	    prot++;
-	}
-    }
-
-    if (prot) {
-	printf ("- Warning: %d protected sectors will not be erased!\n",
-		prot);
-    } else {
-	printf ("\n");
-    }
-
-    l_sect = -1;
-
-    /* Disable interrupts which might cause a timeout here */
-    flag = disable_interrupts();
-
-    addr[0x0555] = 0XAAAAAAAA;
-    addr[0x02AA] = 0x55555555;
-    addr[0x0555] = 0x80808080;
-    addr[0x0555] = 0XAAAAAAAA;
-    addr[0x02AA] = 0x55555555;
-
-    /* Start erase on unprotected sectors */
-    for (sect = s_first; sect<=s_last; sect++) {
-	if (info->protect[sect] == 0) {	/* not protected */
-	    addr = (vu_long*)(info->start[sect]);
-	    addr[0] = 0x30303030;
-	    l_sect = sect;
-	}
-    }
-
-    /* re-enable interrupts if necessary */
-    if (flag)
-      enable_interrupts();
-
-    /* wait at least 80us - let's wait 1 ms */
-    udelay (1000);
-
-    /*
-     * We wait for the last triggered sector
-     */
-    if (l_sect < 0)
-      goto DONE;
-
-    start = get_timer (0);
-    last  = start;
-    addr = (vu_long*)(info->start[l_sect]);
-    while ((addr[0] & 0x80808080) != 0x80808080) {
-	if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
-	    printf ("Timeout\n");
-	    return 1;
-	}
-	/* show that we're waiting */
-	if ((now - last) > 1000) {	/* every second */
-	    serial_putc ('.');
-	    last = now;
-	}
-    }
-
-    DONE:
-    /* reset to read mode */
-    addr = (volatile unsigned long *)info->start[0];
-    addr[0] = 0xF0F0F0F0;	/* reset bank */
-
-    printf (" done\n");
-    return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
-    ulong cp, wp, data;
-    int i, l, rc;
-
-    wp = (addr & ~3);	/* get lower word aligned address */
-
-    /*
-     * handle unaligned start bytes
-     */
-    if ((l = addr - wp) != 0) {
-	data = 0;
-	for (i=0, cp=wp; i<l; ++i, ++cp) {
-	    data = (data << 8) | (*(uchar *)cp);
-	}
-	for (; i<4 && cnt>0; ++i) {
-	    data = (data << 8) | *src++;
-	    --cnt;
-	    ++cp;
-	}
-	for (; cnt==0 && i<4; ++i, ++cp) {
-	    data = (data << 8) | (*(uchar *)cp);
-	}
-
-	if ((rc = write_word(info, wp, data)) != 0) {
-	    return (rc);
-	}
-	wp += 4;
-    }
-
-    /*
-     * handle word aligned part
-     */
-    while (cnt >= 4) {
-	data = 0;
-	for (i=0; i<4; ++i) {
-	    data = (data << 8) | *src++;
-	}
-	if ((rc = write_word(info, wp, data)) != 0) {
-	    return (rc);
-	}
-	wp  += 4;
-	cnt -= 4;
-    }
-
-    if (cnt == 0) {
-	return (0);
-    }
-
-    /*
-     * handle unaligned tail bytes
-     */
-    data = 0;
-    for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
-	data = (data << 8) | *src++;
-	--cnt;
-    }
-    for (; i<4; ++i, ++cp) {
-	data = (data << 8) | (*(uchar *)cp);
-    }
-
-    return (write_word(info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
-    vu_long *addr = (vu_long*)(info->start[0]);
-    ulong start;
-    int flag;
-
-    /* Check if Flash is (sufficiently) erased */
-    if ((*((vu_long *)dest) & data) != data) {
-	return (2);
-    }
-    /* Disable interrupts which might cause a timeout here */
-    flag = disable_interrupts();
-
-    addr[0x0555] = 0xAAAAAAAA;
-    addr[0x02AA] = 0x55555555;
-    addr[0x0555] = 0xA0A0A0A0;
-
-    *((vu_long *)dest) = data;
-
-    /* re-enable interrupts if necessary */
-    if (flag)
-      enable_interrupts();
-
-    /* data polling for D7 */
-    start = get_timer (0);
-    while ((*((vu_long *)dest) & 0x80808080) != (data & 0x80808080)) {
-	if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
-	    return (1);
-	}
-    }
-    return (0);
-}
-
-/*-----------------------------------------------------------------------
- */
diff --git a/board/mbx8xx/mbx8xx.c b/board/mbx8xx/mbx8xx.c
deleted file mode 100644
index 98c723f047..0000000000
--- a/board/mbx8xx/mbx8xx.c
+++ /dev/null
@@ -1,383 +0,0 @@
-/*
- * (C) Copyright 2000
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * Board specific routines for the MBX
- *
- * - initialisation
- * - interface to VPD data (mac address, clock speeds)
- * - memory controller
- * - serial io initialisation
- * - ethernet io initialisation
- *
- * -----------------------------------------------------------------
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <commproc.h>
-#include <mpc8xx.h>
-#include <net.h>
-#include "dimm.h"
-#include "vpd.h"
-#include "csr.h"
-
-/* ------------------------------------------------------------------------- */
-
-static const uint sdram_table_40[] = {
-	/* DRAM - single read. (offset 0 in upm RAM)
-	 */
-	0xCFAFC004, 0x0FAFC404, 0x0CAF0C04, 0x30AF0C00,
-	0xF1BF4805, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
-	/* DRAM - burst read. (offset 8 in upm RAM)
-	 */
-	0xCFAFC004, 0x0FAFC404, 0x0CAF0C04, 0x03AF0C08,
-	0x0CAF0C04, 0x03AF0C08, 0x0CAF0C04, 0x03AF0C08,
-	0x0CAF0C04, 0x30AF0C00, 0xF3BF4805, 0xFFFFC005,
-	0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
-	/* DRAM - single write. (offset 18 in upm RAM)
-	 */
-	0xCFFF0004, 0x0FFF0404, 0x0CFF0C00, 0x33FF4804,
-	0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
-	/* DRAM - burst write. (offset 20 in upm RAM)
-	 */
-	0xCFFF0004, 0x0FFF0404, 0x0CFF0C00, 0x03FF0C0C,
-	0x0CFF0C00, 0x03FF0C0C, 0x0CFF0C00, 0x03FF0C0C,
-	0x0CFF0C00, 0x33FF4804, 0xFFFFC005, 0xFFFFC005,
-	0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
-	/* refresh  (offset 30 in upm RAM)
-	 */
-	0xFCFFC004, 0xC0FFC004, 0x01FFC004, 0x0FFFC004,
-	0x3FFFC004, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-	0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
-	/* exception. (offset 3c in upm RAM)
-	 */
-	0xFFFFC007, 0xFFFFC007, 0xFFFFC007, 0xFFFFC007,
-};
-
-static const uint sdram_table_50[] = {
-	/* DRAM - single read. (offset 0 in upm RAM)
-	 */
-	0xCFAFC004, 0x0FAFC404, 0x0CAF8C04, 0x10AF0C04,
-	0xF0AF0C00, 0xF3BF4805, 0xFFFFC005, 0xFFFFC005,
-
-	/* DRAM - burst read. (offset 8 in upm RAM)
-	 */
-	0xCFAFC004, 0X0FAFC404, 0X0CAF8C04, 0X00AF0C04,
-  /*	0X07AF0C08, 0X0CAF0C04, 0X01AF0C04, 0X0FAF0C04,	*/
-	0X07AF0C08, 0X0CAF0C04, 0X01AF0C04, 0X0FAF0C08,
-	0X0CAF0C04, 0X01AF0C04, 0X0FAF0C08, 0X0CAF0C04,
-  /*	0X10AF0C04, 0XF0AFC000, 0XF3FF4805, 0XFFFFC005,	*/
-	0X10AF0C04, 0XF0AFC000, 0XF3BF4805, 0XFFFFC005,
-
-	/* DRAM - single write. (offset 18 in upm RAM)
-	 */
-	0xCFFF0004, 0x0FFF0404, 0x0CFF0C00, 0x13FF4804,
-	0xFFFFC004, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
-	/* DRAM - burst write. (offset 20 in upm RAM)
-	 */
-	0xCFFF0004, 0x0FFF0404, 0x0CFF0C00, 0x03FF0C0C,
-	0x0CFF0C00, 0x03FF0C0C, 0x0CFF0C00, 0x03FF0C0C,
-	0x0CFF0C00, 0x13FF4804, 0xFFFFC004, 0xFFFFC005,
-	0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
-	/* refresh  (offset 30 in upm RAM)
-	 */
-	0xFCFFC004, 0xC0FFC004, 0x01FFC004, 0x0FFFC004,
-	0x1FFFC004, 0xFFFFC004, 0xFFFFC005, 0xFFFFC005,
-	0xFFFFC005, 0xFFFFC005, 0xFFFFC005, 0xFFFFC005,
-
-	/* exception. (offset 3c in upm RAM)
-	 */
-	0xFFFFC007, 0xFFFFC007, 0xFFFFC007, 0xFFFFC007,
-};
-
-/* ------------------------------------------------------------------------- */
-
-#ifdef CONFIG_SYS_USE_OSCCLK
-static unsigned int get_reffreq(void);
-#endif
-static unsigned int board_get_cpufreq(void);
-
-void mbx_init (void)
-{
-	volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-	volatile memctl8xx_t *memctl = &immr->im_memctl;
-	ulong speed, plprcr, sccr;
-	ulong br0_32 = memctl->memc_br0 & 0x400;
-
-	/* real-time clock status and control register */
-	immr->im_sitk.sitk_rtcsck = KAPWR_KEY;
-	immr->im_sit.sit_rtcsc = 0x00C3;
-
-	/* SIEL and SIMASK Registers (see MBX PRG 2-3) */
-	immr->im_siu_conf.sc_simask = 0x00000000;
-	immr->im_siu_conf.sc_siel = 0xAAAA0000;
-	immr->im_siu_conf.sc_tesr = 0xFFFFFFFF;
-
-	/*
-	 * Prepare access to i2c bus. The MBX offers 3 devices on the i2c bus:
-	 * 1. Vital Product Data (contains clock speeds, MAC address etc, see vpd.h)
-	 * 2. RAM  Specs (see dimm.h)
-	 * 2. DIMM Specs (see dimm.h)
-	 */
-	vpd_init ();
-
-	/* system clock and reset control register */
-	immr->im_clkrstk.cark_sccrk = KAPWR_KEY;
-	sccr = immr->im_clkrst.car_sccr;
-	sccr &= SCCR_MASK;
-	sccr |= CONFIG_SYS_SCCR;
-	immr->im_clkrst.car_sccr = sccr;
-
-	speed = board_get_cpufreq ();
-
-#if ((CONFIG_SYS_PLPRCR & PLPRCR_MF_MSK) != 0)
-	plprcr = CONFIG_SYS_PLPRCR;
-#else
-	plprcr = immr->im_clkrst.car_plprcr;
-	plprcr &= PLPRCR_MF_MSK;	/* isolate MF field */
-	plprcr |= CONFIG_SYS_PLPRCR;		/* reset control bits   */
-#endif
-
-#ifdef CONFIG_SYS_USE_OSCCLK			/* See doc/README.MBX ! */
-	plprcr |= ((speed + get_reffreq() / 2) / refclock - 1) << 20;
-#endif
-
-	immr->im_clkrstk.cark_plprcrk = KAPWR_KEY;
-	immr->im_clkrst.car_plprcr = plprcr;
-
-	/*
-	 * preliminary setup of memory controller:
-	 * - map Flash, otherwise configuration/status
-	 *    registers won't be accessible when read
-	 *    by board_init_f.
-	 * - map NVRAM and configuation/status registers.
-	 * - map pci registers.
-	 * - DON'T map ram yet, this is done in initdram().
-	 */
-	switch (speed / 1000000) {
-	case 40:
-		memctl->memc_br0 = 0xFE000000 | br0_32 | 1;
-		memctl->memc_or0 = 0xFF800930;
-		memctl->memc_or4 = CONFIG_SYS_NVRAM_OR | 0x920;
-		memctl->memc_br4 = CONFIG_SYS_NVRAM_BASE | 0x401;
-		break;
-	case 50:
-		memctl->memc_br0 = 0xFE000000 | br0_32 | 1;
-		memctl->memc_or0 = 0xFF800940;
-		memctl->memc_or4 = CONFIG_SYS_NVRAM_OR | 0x930;
-		memctl->memc_br4 = CONFIG_SYS_NVRAM_BASE | 0x401;
-		break;
-	default:
-		hang ();
-		break;
-	}
-#ifdef CONFIG_USE_PCI
-	memctl->memc_or5 = CONFIG_SYS_PCIMEM_OR;
-	memctl->memc_br5 = CONFIG_SYS_PCIMEM_BASE | 0x001;
-	memctl->memc_or6 = CONFIG_SYS_PCIBRIDGE_OR;
-	memctl->memc_br6 = CONFIG_SYS_PCIBRIDGE_BASE | 0x001;
-#endif
-	/*
-	 * FIXME: I do not understand why I have to call this to
-	 * initialise the control register here before booting from
-	 * the PCMCIA card but if I do not the Linux kernel falls
-	 * over in a big heap. If you can answer this question I
-	 * would like to know about it.
-	 */
-	board_ether_init();
-}
-
-void board_serial_init (void)
-{
-	MBX_CSR1 &= ~(CSR1_COM1EN | CSR1_XCVRDIS);
-}
-
-void board_ether_init (void)
-{
-	MBX_CSR1 &= ~(CSR1_EAEN | CSR1_ELEN);
-	MBX_CSR1 |= CSR1_ETEN | CSR1_TPEN | CSR1_FDDIS;
-}
-
-static unsigned int board_get_cpufreq (void)
-{
-#ifndef CONFIG_8xx_GCLK_FREQ
-	vpd_packet_t *packet;
-	ulong *p;
-
-	packet = vpd_find_packet (VPD_PID_ICS);
-	p = (ulong *)packet->data;
-	return *p;
-#else
-	return((unsigned int)CONFIG_8xx_GCLK_FREQ );
-#endif /* CONFIG_8xx_GCLK_FREQ */
-}
-
-#ifdef CONFIG_SYS_USE_OSCCLK
-static unsigned int get_reffreq (void)
-{
-	vpd_packet_t *packet;
-	ulong *p;
-
-	packet = vpd_find_packet (VPD_PID_RCS);
-	p = (ulong *)packet->data;
-	return *p;
-}
-#endif
-
-static void board_get_enetaddr(uchar *addr)
-{
-	int i;
-	vpd_packet_t *packet;
-
-	packet = vpd_find_packet (VPD_PID_EA);
-	for (i = 0; i < 6; i++)
-		addr[i] = packet->data[i];
-}
-
-int misc_init_r(void)
-{
-	uchar enetaddr[6];
-
-	if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
-		board_get_enetaddr(enetaddr);
-		eth_setenv_enetaddr("ethaddr", enetaddr);
-	}
-
-	return 0;
-}
-
-/*
- * Check Board Identity:
- */
-
-int checkboard (void)
-{
-	vpd_packet_t *packet;
-	int i;
-	const char *const fmt =
-		"\n	 *** Warning: Low Battery Status - %s Battery ***";
-
-	puts ("Board: ");
-
-	packet = vpd_find_packet (VPD_PID_PID);
-	for (i = 0; i < packet->size; i++) {
-		serial_putc (packet->data[i]);
-	}
-	packet = vpd_find_packet (VPD_PID_MT);
-	for (i = 0; i < packet->size; i++) {
-		serial_putc (packet->data[i]);
-	}
-	serial_putc ('(');
-	packet = vpd_find_packet (VPD_PID_FAN);
-	for (i = 0; i < packet->size; i++) {
-		serial_putc (packet->data[i]);
-	}
-	serial_putc (')');
-
-	if (!(MBX_CSR2 & SR2_BATGD))
-		printf (fmt, "On-Board");
-	if (!(MBX_CSR2 & SR2_NVBATGD))
-		printf (fmt, "NVRAM");
-
-	serial_putc ('\n');
-
-	return (0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-static ulong get_ramsize (dimm_t * dimm)
-{
-	ulong size = 0;
-
-	if (dimm->fmt == 1 || dimm->fmt == 2 || dimm->fmt == 3
-		|| dimm->fmt == 4) {
-		size = (1 << (dimm->n_row + dimm->n_col)) * dimm->n_banks *
-			((dimm->data_w_hi << 8 | dimm->data_w_lo) / 8);
-	}
-
-	return size;
-}
-
-phys_size_t initdram (int board_type)
-{
-	volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-	volatile memctl8xx_t *memctl = &immap->im_memctl;
-	unsigned long ram_sz = 0;
-	unsigned long dimm_sz = 0;
-	dimm_t vpd_dimm, vpd_dram;
-	unsigned int speed = board_get_cpufreq () / 1000000;
-
-	if (vpd_read (0xa2, (uchar *) & vpd_dimm, sizeof (vpd_dimm), 0) > 0) {
-		dimm_sz = get_ramsize (&vpd_dimm);
-	}
-	if (vpd_read (0xa6, (uchar *) & vpd_dram, sizeof (vpd_dram), 0) > 0) {
-		ram_sz = get_ramsize (&vpd_dram);
-	}
-
-	/*
-	 * Only initialize memory controller when running from FLASH.
-	 * When running from RAM, don't touch it.
-	 */
-	if ((ulong) initdram & 0xff000000) {
-		ulong dimm_bank;
-		ulong br0_32 = memctl->memc_br0 & 0x400;
-
-		switch (speed) {
-		case 40:
-			upmconfig (UPMA, (uint *) sdram_table_40,
-					   sizeof (sdram_table_40) / sizeof (uint));
-			memctl->memc_mptpr = 0x0200;
-			memctl->memc_mamr = dimm_sz ? 0x06801000 : 0x13801000;
-			memctl->memc_or7 = 0xff800930;
-			memctl->memc_br7 = 0xfc000000 | (br0_32 ^ br0_32) | 1;
-			break;
-		case 50:
-			upmconfig (UPMA, (uint *) sdram_table_50,
-					   sizeof (sdram_table_50) / sizeof (uint));
-			memctl->memc_mptpr = 0x0200;
-			memctl->memc_mamr = dimm_sz ? 0x08801000 : 0x1880100;
-			memctl->memc_or7 = 0xff800940;
-			memctl->memc_br7 = 0xfc000000 | (br0_32 ^ br0_32) | 1;
-			break;
-		default:
-			hang ();
-			break;
-		}
-
-		/* now map ram and dimm, largest one first */
-		dimm_bank = dimm_sz / 2;
-		if (!dimm_sz) {
-			memctl->memc_or1 = ~(ram_sz - 1) | 0x400;
-			memctl->memc_br1 = CONFIG_SYS_SDRAM_BASE | 0x81;
-			memctl->memc_br2 = 0;
-			memctl->memc_br3 = 0;
-		} else if (ram_sz > dimm_bank) {
-			memctl->memc_or1 = ~(ram_sz - 1) | 0x400;
-			memctl->memc_br1 = CONFIG_SYS_SDRAM_BASE | 0x81;
-			memctl->memc_or2 = ~(dimm_bank - 1) | 0x400;
-			memctl->memc_br2 = (CONFIG_SYS_SDRAM_BASE + ram_sz) | 0x81;
-			memctl->memc_or3 = ~(dimm_bank - 1) | 0x400;
-			memctl->memc_br3 = (CONFIG_SYS_SDRAM_BASE + ram_sz + dimm_bank) \
-								     | 0x81;
-		} else {
-			memctl->memc_or2 = ~(dimm_bank - 1) | 0x400;
-			memctl->memc_br2 = CONFIG_SYS_SDRAM_BASE | 0x81;
-			memctl->memc_or3 = ~(dimm_bank - 1) | 0x400;
-			memctl->memc_br3 = (CONFIG_SYS_SDRAM_BASE + dimm_bank) | 0x81;
-			memctl->memc_or1 = ~(ram_sz - 1) | 0x400;
-			memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE + dimm_sz) | 0x81;
-		}
-	}
-
-	return ram_sz + dimm_sz;
-}
diff --git a/board/mbx8xx/pcmcia.c b/board/mbx8xx/pcmcia.c
deleted file mode 100644
index 497e260a0a..0000000000
--- a/board/mbx8xx/pcmcia.c
+++ /dev/null
@@ -1,156 +0,0 @@
-#include <common.h>
-#include <mpc8xx.h>
-#include <pcmcia.h>
-
-#include "csr.h"
-
-#undef	CONFIG_PCMCIA
-
-#if defined(CONFIG_CMD_PCMCIA)
-#define	CONFIG_PCMCIA
-#endif
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
-#define	CONFIG_PCMCIA
-#endif
-
-#ifdef	CONFIG_PCMCIA
-
-/* A lot of this has been taken from the RPX code in this file it works from me.
-   I have added the voltage selection for the MBX board. */
-
-/* MBX voltage bit in control register #2 */
-#define CR2_VPP12       ((uchar)0x10)
-#define CR2_VPPVDD      ((uchar)0x20)
-#define CR2_VDD5        ((uchar)0x40)
-#define CR2_VDD3        ((uchar)0x80)
-
-#define PCMCIA_BOARD_MSG "MBX860"
-
-int pcmcia_voltage_set (int slot, int vcc, int vpp)
-{
-	uchar reg = 0;
-
-	debug ("voltage_set: PCMCIA_BOARD_MSG Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
-	       'A' + slot, vcc / 10, vcc % 10, vpp / 10, vcc % 10);
-
-	switch (vcc) {
-		case 0:
-			break;
-		case 33:
-			reg |= CR2_VDD3;
-			break;
-		case 50:
-			reg |= CR2_VDD5;
-			break;
-		default:
-			return 1;
-	}
-
-	switch (vpp) {
-		case 0:
-			break;
-		case 33:
-		case 50:
-			if (vcc == vpp) {
-				reg |= CR2_VPPVDD;
-			} else {
-				return 1;
-			}
-			break;
-		case 120:
-			reg |= CR2_VPP12;
-			break;
-		default:
-			return 1;
-	}
-
-	/* first, turn off all power */
-	MBX_CSR2 &= ~(CR2_VDDSEL | CR2_VPPSEL);
-
-	/* enable new powersettings */
-	MBX_CSR2 |= reg;
-	debug ("MBX_CSR2 read = 0x%02x\n", MBX_CSR2);
-
-	return (0);
-}
-
-int pcmcia_hardware_enable (int slot)
-{
-	volatile pcmconf8xx_t *pcmp;
-	uint reg, mask;
-
-	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n",
-	       'A' + slot);
-
-	udelay (10000);
-
-	pcmp = (pcmconf8xx_t *) (&(((immap_t *) CONFIG_SYS_IMMR)->im_pcmcia));
-
-	/* clear interrupt state, and disable interrupts */
-	pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
-	pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
-
-	/*
-	* Disable interrupts, DMA, and PCMCIA buffers
-	* (isolate the interface) and assert RESET signal
-	*/
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;	/* active low  */
-	PCMCIA_PGCRX (_slot_) = reg;
-	udelay (500);
-
-	/* remove all power */
-	pcmcia_voltage_set (slot, 0, 0);
-	/*
-	* Make sure there is a card in the slot, then configure the interface.
-	*/
-	udelay(10000);
-	debug ("[%d] %s: PIPR(%p)=0x%x\n",
-	       __LINE__,__FUNCTION__,
-	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-	if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) {
-		printf ("   No Card found\n");
-		return (1);
-	}
-
-	/*
-	* Power On.
-	*/
-	mask = PCMCIA_VS1 (_slot_) | PCMCIA_VS2 (_slot_);
-	reg = pcmp->pcmc_pipr;
-	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", reg,
-	       (reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
-	       (reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
-
-	if ((reg & mask) == mask) {
-		pcmcia_voltage_set (_slot_, 50, 0);
-		printf (" 5.0V card found: ");
-	} else {
-		pcmcia_voltage_set (_slot_, 33, 0);
-		printf (" 3.3V card found: ");
-	}
-
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg = PCMCIA_PGCRX (_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;	/* active low  */
-	PCMCIA_PGCRX (_slot_) = reg;
-
-	udelay (250000);	/* some cards need >150 ms to come up :-( */
-
-	debug ("# hardware_enable done\n");
-
-	return (0);
-	}
-
-#if defined(CONFIG_CMD_PCMCIA)
-int pcmcia_hardware_disable (int slot)
-{
-	return 0;	/* No hardware to disable */
-}
-#endif
-
-#endif	/* CONFIG_PCMCIA */
diff --git a/board/mbx8xx/u-boot.lds b/board/mbx8xx/u-boot.lds
deleted file mode 100644
index 0eb2fba00c..0000000000
--- a/board/mbx8xx/u-boot.lds
+++ /dev/null
@@ -1,82 +0,0 @@
-/*
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
-  /* Read-only sections, merged into text segment: */
-  . = + SIZEOF_HEADERS;
-  .text      :
-  {
-    arch/powerpc/cpu/mpc8xx/start.o	(.text*)
-    arch/powerpc/cpu/mpc8xx/traps.o	(.text*)
-
-    *(.text*)
-  }
-  _etext = .;
-  PROVIDE (etext = .);
-  .rodata    :
-  {
-    *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-  }
-
-  /* Read-write section, merged into data segment: */
-  . = (. + 0x00FF) & 0xFFFFFF00;
-  _erotext = .;
-  PROVIDE (erotext = .);
-  .reloc   :
-  {
-    _GOT2_TABLE_ = .;
-    KEEP(*(.got2))
-    KEEP(*(.got))
-    PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
-    _FIXUP_TABLE_ = .;
-    KEEP(*(.fixup))
-  }
-  __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
-  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
-  .data    :
-  {
-    *(.data*)
-    *(.sdata*)
-  }
-  _edata  =  .;
-  PROVIDE (edata = .);
-
-  . = .;
-
-  . = ALIGN(4);
-  .u_boot_list : {
-	KEEP(*(SORT(.u_boot_list*)));
-  }
-
-
-  . = .;
-  __start___ex_table = .;
-  __ex_table : { *(__ex_table) }
-  __stop___ex_table = .;
-
-  . = ALIGN(256);
-  __init_begin = .;
-  .text.init : { *(.text.init) }
-  .data.init : { *(.data.init) }
-  . = ALIGN(256);
-  __init_end = .;
-
-  __bss_start = .;
-  .bss (NOLOAD)       :
-  {
-   *(.bss*)
-   *(.sbss*)
-   *(COMMON)
-   . = ALIGN(4);
-  }
-  __bss_end = . ;
-  PROVIDE (end = .);
-}
diff --git a/board/mbx8xx/u-boot.lds.debug b/board/mbx8xx/u-boot.lds.debug
deleted file mode 100644
index 7cfed1f1d5..0000000000
--- a/board/mbx8xx/u-boot.lds.debug
+++ /dev/null
@@ -1,122 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
-   __DYNAMIC = 0;    */
-SECTIONS
-{
-  /* Read-only sections, merged into text segment: */
-  . = + SIZEOF_HEADERS;
-  .interp : { *(.interp) }
-  .hash          : { *(.hash)		}
-  .dynsym        : { *(.dynsym)		}
-  .dynstr        : { *(.dynstr)		}
-  .rel.text      : { *(.rel.text)		}
-  .rela.text     : { *(.rela.text)	}
-  .rel.data      : { *(.rel.data)		}
-  .rela.data     : { *(.rela.data)	}
-  .rel.rodata    : { *(.rel.rodata)	}
-  .rela.rodata   : { *(.rela.rodata)	}
-  .rel.got       : { *(.rel.got)		}
-  .rela.got      : { *(.rela.got)		}
-  .rel.ctors     : { *(.rel.ctors)	}
-  .rela.ctors    : { *(.rela.ctors)	}
-  .rel.dtors     : { *(.rel.dtors)	}
-  .rela.dtors    : { *(.rela.dtors)	}
-  .rel.bss       : { *(.rel.bss)		}
-  .rela.bss      : { *(.rela.bss)		}
-  .rel.plt       : { *(.rel.plt)		}
-  .rela.plt      : { *(.rela.plt)		}
-  .init          : { *(.init)	}
-  .plt : { *(.plt) }
-  .text      :
-  {
-    /* WARNING - the following is hand-optimized to fit within	*/
-    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
-
-    arch/powerpc/cpu/mpc8xx/start.o	(.text)
-    common/dlmalloc.o	(.text)
-    lib/vsprintf.o	(.text)
-    lib/crc32.o		(.text)
-    arch/powerpc/lib/extable.o	(.text)
-
-    . = env_offset;
-    common/env_embedded.o(.text)
-
-    *(.text)
-    *(.got1)
-  }
-  _etext = .;
-  PROVIDE (etext = .);
-  .rodata    :
-  {
-    *(.rodata)
-    *(.rodata1)
-    *(.rodata.str1.4)
-    *(.eh_frame)
-  }
-  .fini      : { *(.fini)    } =0
-  .ctors     : { *(.ctors)   }
-  .dtors     : { *(.dtors)   }
-
-  /* Read-write section, merged into data segment: */
-  . = (. + 0x0FFF) & 0xFFFFF000;
-  _erotext = .;
-  PROVIDE (erotext = .);
-  .reloc   :
-  {
-    *(.got)
-    _GOT2_TABLE_ = .;
-    *(.got2)
-    _FIXUP_TABLE_ = .;
-    *(.fixup)
-  }
-  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
-  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
-  .data    :
-  {
-    *(.data)
-    *(.data1)
-    *(.sdata)
-    *(.sdata2)
-    *(.dynamic)
-    CONSTRUCTORS
-  }
-  _edata  =  .;
-  PROVIDE (edata = .);
-
-
-  . = ALIGN(4);
-  .u_boot_list : {
-	KEEP(*(SORT(.u_boot_list*)));
-  }
-
-
-  __start___ex_table = .;
-  __ex_table : { *(__ex_table) }
-  __stop___ex_table = .;
-
-  . = ALIGN(4096);
-  __init_begin = .;
-  .text.init : { *(.text.init) }
-  .data.init : { *(.data.init) }
-  . = ALIGN(4096);
-  __init_end = .;
-
-  __bss_start = .;
-  .bss       :
-  {
-   *(.sbss) *(.scommon)
-   *(.dynbss)
-   *(.bss)
-   *(COMMON)
-  }
-  __bss_end = . ;
-  PROVIDE (end = .);
-}
diff --git a/board/mbx8xx/vpd.c b/board/mbx8xx/vpd.c
deleted file mode 100644
index 1ba754ee23..0000000000
--- a/board/mbx8xx/vpd.c
+++ /dev/null
@@ -1,180 +0,0 @@
-/*
- * (C) Copyright 2000
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * Code in faintly related to linux/arch/powerpc/8xx_io:
- * MPC8xx CPM I2C interface. Copyright (c) 1999 Dan Malek (dmalek@jlc.net).
- *
- * This file implements functions to read the MBX's Vital Product Data
- * (VPD). I can't use the more general i2c code in mpc8xx/... since I need
- * the VPD at a time where there is no RAM available yet. Hence the VPD is
- * read into a special area in the DPRAM (see config_MBX.h::CFG_DPRAMVPD).
- *
- * -----------------------------------------------------------------
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#ifdef CONFIG_8xx
-#include <commproc.h>
-#endif
-#include "vpd.h"
-
-/* Location of receive/transmit buffer descriptors
- * Allocate one transmit bd and one receive bd.
- * IIC_BD_FREE points to free bd space which we'll use as tx buffer.
- */
-#define IIC_BD_TX1     (BD_IIC_START + 0*sizeof(cbd_t))
-#define IIC_BD_TX2     (BD_IIC_START + 1*sizeof(cbd_t))
-#define IIC_BD_RX      (BD_IIC_START + 2*sizeof(cbd_t))
-#define IIC_BD_FREE    (BD_IIC_START + 3*sizeof(cbd_t))
-
-/* FIXME -- replace 0x2000 with offsetof */
-#define VPD_P ((vpd_t *)(CONFIG_SYS_IMMR + 0x2000 + CONFIG_SYS_DPRAMVPD))
-
-/* transmit/receive buffers */
-#define IIC_RX_LENGTH 128
-
-#define WITH_MICROCODE_PATCH
-
-vpd_packet_t * vpd_find_packet(u_char ident)
-{
-    vpd_packet_t *packet;
-    vpd_t *vpd = VPD_P;
-
-    packet = (vpd_packet_t *)&vpd->packets;
-    while ((packet->identifier != ident) && packet->identifier != 0xFF)
-    {
-	packet = (vpd_packet_t *)((char *)packet + packet->size + 2);
-    }
-    return packet;
-}
-
-void vpd_init(void)
-{
-    volatile immap_t  *im = (immap_t *)CONFIG_SYS_IMMR;
-    volatile cpm8xx_t *cp = &(im->im_cpm);
-    volatile i2c8xx_t *i2c = (i2c8xx_t *)&(im->im_i2c);
-    volatile iic_t *iip;
-#ifdef WITH_MICROCODE_PATCH
-    ulong reloc = 0;
-#endif
-
-    iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
-
-    /*
-     * kludge: when running from flash, no microcode patch can be
-     * installed. However, the DPMEM usually contains non-zero
-     * garbage at the relocatable patch base location, so lets clear
-     * it now. This way the rest of the code can support the microcode
-     * patch dynamically.
-     */
-    if ((ulong)vpd_init & 0xff000000)
-      iip->iic_rpbase = 0;
-
-#ifdef WITH_MICROCODE_PATCH
-    /* Check for and use a microcode relocation patch. */
-    if ((reloc = iip->iic_rpbase))
-      iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
-#endif
-    /* Initialize Port B IIC pins */
-    cp->cp_pbpar |= 0x00000030;
-    cp->cp_pbdir |= 0x00000030;
-    cp->cp_pbodr |= 0x00000030;
-
-    i2c->i2c_i2mod = 0x04;  /* filter clock */
-    i2c->i2c_i2add = 0x34;	/* select an arbitrary (unique) address */
-    i2c->i2c_i2brg = 0x07;  /* make clock run maximum slow	*/
-    i2c->i2c_i2cmr = 0x00;  /* disable interrupts */
-    i2c->i2c_i2cer = 0x1f;  /* clear events */
-    i2c->i2c_i2com = 0x01;  /* configure i2c to work as master */
-
-    if (vpd_read(0xa4, (uchar*)VPD_P, VPD_EEPROM_SIZE, 0) != VPD_EEPROM_SIZE)
-    {
-	hang();
-    }
-}
-
-
-/* Read from I2C.
- * This is a two step process.  First, we send the "dummy" write
- * to set the device offset for the read.  Second, we perform
- * the read operation.
- */
-int vpd_read(uint iic_device, uchar *buf, int count, int offset)
-{
-    volatile immap_t  *im = (immap_t *)CONFIG_SYS_IMMR;
-    volatile cpm8xx_t *cp = &(im->im_cpm);
-    volatile i2c8xx_t *i2c = (i2c8xx_t *)&(im->im_i2c);
-    volatile iic_t *iip;
-    volatile cbd_t *tbdf1, *tbdf2, *rbdf;
-    uchar *tb;
-    uchar event;
-#ifdef WITH_MICROCODE_PATCH
-    ulong reloc = 0;
-#endif
-
-    iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
-#ifdef WITH_MICROCODE_PATCH
-    /* Check for and use a microcode relocation patch. */
-    if ((reloc = iip->iic_rpbase))
-      iip = (iic_t *)&cp->cp_dpmem[iip->iic_rpbase];
-#endif
-    tbdf1 = (cbd_t *)&cp->cp_dpmem[IIC_BD_TX1];
-    tbdf2 = (cbd_t *)&cp->cp_dpmem[IIC_BD_TX2];
-    rbdf  = (cbd_t *)&cp->cp_dpmem[IIC_BD_RX];
-
-    /* Send a "dummy write" operation.  This is a write request with
-     * only the offset sent, followed by another start condition.
-     * This will ensure we start reading from the first location
-     * of the EEPROM.
-     */
-    tb = (uchar*)&cp->cp_dpmem[IIC_BD_FREE];
-    tb[0] = iic_device & 0xfe;	/* device address */
-    tb[1] = offset;	        /* offset */
-    tbdf1->cbd_bufaddr = (uint)tb;
-    tbdf1->cbd_datlen = 2;
-    tbdf1->cbd_sc = 0x8400;
-
-    tb += 2;
-    tb[0] = iic_device | 1;	/* device address */
-    tbdf2->cbd_bufaddr = (uint)tb;
-    tbdf2->cbd_datlen = count+1;
-    tbdf2->cbd_sc = 0xbc00;
-
-    rbdf->cbd_bufaddr = (uint)buf;
-    rbdf->cbd_datlen = 0;
-    rbdf->cbd_sc = 0xb000;
-
-    iip->iic_tbase = IIC_BD_TX1;
-    iip->iic_tbptr = IIC_BD_TX1;
-    iip->iic_rbase = IIC_BD_RX;
-    iip->iic_rbptr = IIC_BD_RX;
-    iip->iic_rfcr = 0x15;
-    iip->iic_tfcr = 0x15;
-    iip->iic_mrblr = count;
-    iip->iic_rstate = 0;
-    iip->iic_tstate = 0;
-
-    i2c->i2c_i2cer = 0x1f;  /* clear event mask */
-    i2c->i2c_i2mod |= 1;    /* enable iic operation */
-    i2c->i2c_i2com |= 0x80;	/* start master */
-
-    /* wait for IIC transfer */
-    do {
-	__asm__ volatile ("eieio");
-	event = i2c->i2c_i2cer;
-    } while (event == 0);
-
-    if ((event & 0x10) || (event & 0x04)) {
-	count = -1;
-	goto bailout;
-    }
-
-bailout:
-    i2c->i2c_i2mod &= ~1;   /* turn off iic operation */
-    i2c->i2c_i2cer = 0x1f;  /* clear event mask */
-
-    return count;
-}
diff --git a/board/mbx8xx/vpd.h b/board/mbx8xx/vpd.h
deleted file mode 100644
index 1d9eb7fe20..0000000000
--- a/board/mbx8xx/vpd.h
+++ /dev/null
@@ -1,119 +0,0 @@
-#ifndef __vpd_h
-#define __vpd_h
-
-/*
- * Module name: %M%
- * Description:
- * Vital Product Data (VPD) Header Module
- * SCCS identification: %I%
- * Branch: %B%
- * Sequence: %S%
- * Date newest applied delta was created (MM/DD/YY): %G%
- * Time newest applied delta was created (HH:MM:SS): %U%
- * SCCS file name %F%
- * Fully qualified SCCS file name:
- * %P%
- * Copyright:
- * (C) COPYRIGHT MOTOROLA, INC. 1996
- * ALL RIGHTS RESERVED
- * Notes:
- * History:
- * Date Who
- *
- * 10/24/96 Rob Baxter
- * Initial release.
- *
- */
-
-#define VPD_EEPROM_SIZE 256 /* EEPROM size in bytes */
-
-/*
- * packet tuple identifiers
- *
- * 0x0D - 0xBF reserved
- * 0xC0 - 0xFE user defined
- */
-#define VPD_PID_GI   0x00 /* guaranteed illegal */
-#define VPD_PID_PID  0x01 /* product identifier (ASCII) */
-#define VPD_PID_FAN  0x02 /* factory assembly-number (ASCII) */
-#define VPD_PID_SN   0x03 /* serial-number (ASCII) */
-#define VPD_PID_PCO  0x04 /* product configuration options(binary) */
-#define VPD_PID_ICS  0x05 /* internal clock speed in HZ (integer) */
-#define VPD_PID_ECS  0x06 /* external clock speed in HZ (integer) */
-#define VPD_PID_RCS  0x07 /* reference clock speed in HZ(integer) */
-#define VPD_PID_EA   0x08 /* ethernet address (binary) */
-#define VPD_PID_MT   0x09 /* microprocessor type (ASCII) */
-#define VPD_PID_CRC  0x0A /* EEPROM CRC (integer) */
-#define VPD_PID_FMC  0x0B /* FLASH memory configuration (binary) */
-#define VPD_PID_VLSI 0x0C /* VLSI revisions/versions (binary) */
-#define VPD_PID_TERM 0xFF /* termination */
-
-/*
- * VPD structure (format)
- */
-#define VPD_EYE_SIZE 8 /* eyecatcher size */
-typedef struct vpd_header
-{
-	uchar eyecatcher[VPD_EYE_SIZE]; /* eyecatcher - "MOTOROLA" */
-	ushort size; /* size of EEPROM */
-} vpd_header_t;
-
-#define VPD_DATA_SIZE (VPD_EEPROM_SIZE-sizeof(vpd_header_t))
-typedef struct vpd
-{
-	vpd_header_t header; /* header */
-	uchar packets[VPD_DATA_SIZE]; /* data */
-} vpd_t;
-
-/*
- * packet tuple structure (format)
- */
-typedef struct vpd_packet
-{
-    uchar identifier; /* identifier (PIDs above) */
-    uchar size;       /* size of the following data area */
-    uchar data[1];    /* data (size is dependent upon PID) */
-} vpd_packet_t;
-
-/*
- * MBX product configuration options bit definitions
- *
- * Notes:
- * 1. The bit numbering is reversed in perspective with the C compiler.
- */
-#define PCO_BBRAM    (1<<0)  /* battery-backed RAM (BBRAM) and socket */
-#define PCO_BOOTROM  (1<<1)  /* boot ROM and socket (i.e., socketed FLASH) */
-#define PCO_KAPWR    (1<<2)  /* keep alive power source (lithium battey) and control circuit */
-#define PCO_ENET_TP  (1<<3)  /* ethernet twisted pair (TP) connector (RJ45) */
-#define PCO_ENET_AUI (1<<4)  /* ethernet attachment unit interface (AUI) header */
-#define PCO_PCMCIA   (1<<5)  /* PCMCIA socket */
-#define PCO_DIMM     (1<<6)  /* DIMM module socket */
-#define PCO_DTT      (1<<7)  /* digital thermometer and thermostat (DTT) device */
-#define PCO_LCD      (1<<8)  /* liquid crystal display (LCD) device */
-#define PCO_PCI      (1<<9)  /* PCI-Bus bridge device (QSpan) and ISA-Bus bridge device (Winbond) */
-#define PCO_PCIO     (1<<10) /* PC I/O (COM1, COM2, FDC, LPT, Keyboard/Mouse) */
-#define PCO_EIDE     (1<<11) /* enhanced IDE (EIDE) header */
-#define PCO_FDC      (1<<12) /* floppy disk controller (FDC) header */
-#define PCO_LPT_8XX  (1<<13) /* parallel port header via MPC8xx */
-#define PCO_LPT_PCIO (1<<14) /* parallel port header via PC I/O */
-
-/*
- * FLASH memory configuration packet data
- */
-typedef struct vpd_fmc
-{
-    ushort mid; /* manufacturer's idenitfier */
-    ushort did; /* manufacturer's device idenitfier */
-    uchar ddw;  /* device data width (e.g., 8-bits, 16-bits) */
-    uchar nod;  /* number of devices present */
-    uchar noc;  /* number of columns */
-    uchar cw;   /* column width in bits */
-    uchar wedw; /* write/erase data width */
-} vpd_fmc_t;
-
-/* function prototypes */
-extern void vpd_init(void);
-extern int  vpd_read(uint iic_device, uchar *buf, int count, int offset);
-extern      vpd_packet_t *vpd_find_packet(u_char ident);
-
-#endif /* __vpd_h */
diff --git a/boards.cfg b/boards.cfg
index 26e784b01c..384f319382 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -1253,5 +1253,3 @@ Orphan  powerpc     mpc8xx         -           -               fads
 Orphan  powerpc     mpc8xx         -           -               fads                FADS850SAR                           -                                                                                                                                 -
 Orphan  powerpc     mpc8xx         -           -               fads                FADS860T                             -                                                                                                                                 -
 Orphan  powerpc     mpc8xx         -           -               genietv             GENIETV                              -                                                                                                                                 -
-Orphan  powerpc     mpc8xx         -           -               mbx8xx              MBX                                  -                                                                                                                                 -
-Orphan  powerpc     mpc8xx         -           -               mbx8xx              MBX860T                              -                                                                                                                                 -
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 7f519916fd..4e0ad323c7 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -11,6 +11,7 @@ easily if here is something they might want to dig for...
 
 Board            Arch        CPU            Commit      Removed     Last known maintainer/contact
 =================================================================================================
+mbx8xx           powerpc     mpc8xx         -           2014-04-04
 nx823            powerpc     mpc8xx         -           2014-04-04
 idmr             m68k        mcf52x2        ba650e9b    2014-01-28
 M5271EVB         m68k        mcf52x2        ba650e9b    2014-01-28
diff --git a/include/common.h b/include/common.h
index cbd3c9e043..580615b9ef 100644
--- a/include/common.h
+++ b/include/common.h
@@ -511,13 +511,6 @@ void rpxclassic_init (void);
 
 void rpxlite_init (void);
 
-#ifdef CONFIG_MBX
-/* $(BOARD)/mbx8xx.c */
-void	mbx_init (void);
-void	board_serial_init (void);
-void	board_ether_init (void);
-#endif
-
 #ifdef CONFIG_HERMES
 /* $(BOARD)/hermes.c */
 void hermes_start_lxt980 (int speed);
diff --git a/include/commproc.h b/include/commproc.h
index 12b9421060..62468c30aa 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -12,10 +12,6 @@
  * CPM capabilities.  I (or someone else) will add definitions as they
  * are needed.  -- Dan
  *
- * On the MBX board, EPPC-Bug loads CPM microcode into the first 512
- * bytes of the DP RAM and relocates the I2C parameter area to the
- * IDMA1 space.  The remaining DP RAM is available for buffer descriptors
- * or other use.
  */
 #ifndef __CPM_8XX__
 #define __CPM_8XX__
@@ -135,7 +131,6 @@ typedef struct cpm_buf_desc {
 #define PROFF_SMC2	((uint)0x0380)
 
 /* Define enough so I can at least use the serial port as a UART.
- * The MBX uses SMC1 as the host serial port.
  */
 typedef struct smc_uart {
 	ushort	smc_rbase;	/* Rx Buffer descriptor base address */
@@ -888,33 +883,6 @@ typedef struct scc_enet {
 #define SICR_ENET_CLKRT	((uint)0x00003E00)
 #endif	/* CONFIG_LWMON */
 
-/***  MBX  ************************************************************/
-
-#ifdef CONFIG_MBX
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.  The TCLK and RCLK seem unique
- * to the MBX860 board.  Any two of the four available clocks could be
- * used, and the MPC860 cookbook manual has an example using different
- * clock pins.
- */
-#define	PROFF_ENET	PROFF_SCC1
-#define	CPM_CR_ENET	CPM_CR_CH_SCC1
-#define	SCC_ENET	0
-#define PA_ENET_RXD	((ushort)0x0001)
-#define PA_ENET_TXD	((ushort)0x0002)
-#define PA_ENET_TCLK	((ushort)0x0200)
-#define PA_ENET_RCLK	((ushort)0x0800)
-#define PC_ENET_TENA	((ushort)0x0001)
-#define PC_ENET_CLSN	((ushort)0x0010)
-#define PC_ENET_RENA	((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK	((uint)0x000000ff)
-#define SICR_ENET_CLKRT	((uint)0x0000003d)
-#endif	/* CONFIG_MBX */
-
 /***  KM8XX  *********************************************************/
 
 /* The KM8XX Service Module uses SCC3 for Ethernet */
diff --git a/include/configs/MBX.h b/include/configs/MBX.h
deleted file mode 100644
index 96edd442d0..0000000000
--- a/include/configs/MBX.h
+++ /dev/null
@@ -1,290 +0,0 @@
-/*
- * (C) Copyright 2000
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * Configuation settings for the MBX8xx board.
- *
- * -----------------------------------------------------------------
- * SPDX-License-Identifier:	GPL-2.0+
- */
-/*
- * Changed 2002-10-01
- * Added PCMCIA defines mostly taken from other U-Boot boards that
- * have PCMCIA already working.  If you find any bugs, incorrect assumptions
- * feel free to fix them yourself and submit a patch.
- * Rod Boyce <rod_boyce@stratexnet.com.
- */
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860		1	/* This is a MPC860 CPU		*/
-#define CONFIG_MBX		1	/* ...on an MBX module		*/
-
-#define	CONFIG_SYS_TEXT_BASE	0xfe000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		9600
-/* Define this to use the PCI bus */
-#undef CONFIG_USE_PCI
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-#define CONFIG_8xx_GCLK_FREQ    (50000000UL)
-#if 1
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-#define CONFIG_BOOTCOMMAND	"bootm 20000" /* autoboot command	*/
-
-#define CONFIG_BOOTARGS		"root=/dev/nfs rw "			\
-				"nfsroot=10.0.0.2:/opt/eldk/ppc_8xx "	\
-				"nfsaddrs=10.0.0.99:10.0.0.2"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE   /* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_PCMCIA
-#define CONFIG_CMD_IDE
-
-
-#define CONFIG_DOS_PARTITION
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#undef	CONFIG_SYS_HUSH_PARSER			/* Hush parse for U-Boot	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-/*-----------------------------------------------------------------------
- * Physical memory map as defined by the MBX PGM
- */
-#define CONFIG_SYS_IMMR		0xFA200000 /* Internal Memory Mapped Register*/
-#define CONFIG_SYS_NVRAM_BASE		0xFA000000 /* NVRAM			     */
-#define CONFIG_SYS_NVRAM_OR		0xffe00000 /* w/o speed dependent flags!!    */
-#define CONFIG_SYS_CSR_BASE		0xFA100000 /* Control/Status Registers	     */
-#define CONFIG_SYS_PCIMEM_BASE		0x80000000 /* PCI I/O and Memory Spaces	     */
-#define CONFIG_SYS_PCIMEM_OR		0xA0000108
-#define CONFIG_SYS_PCIBRIDGE_BASE	0xFA210000 /* PCI-Bus Bridge Registers	     */
-#define CONFIG_SYS_PCIBRIDGE_OR	0xFFFF0108
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2f00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_VPD_SIZE	256 /* size in bytes reserved for vpd buffer */
-#define CONFIG_SYS_INIT_VPD_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_VPD_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_INIT_VPD_OFFSET-8)
-
-/*-----------------------------------------------------------------------
- * Offset in DPMEM where we keep the VPD data
- */
-#define CONFIG_SYS_DPRAMVPD		(CONFIG_SYS_INIT_VPD_OFFSET - 0x2000)
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0xfe000000
-#ifdef	DEBUG
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#else
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#endif
-#undef	CONFIG_SYS_MONITOR_BASE	/* 0x200000	   to run U-Boot from RAM */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	16	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-/*-----------------------------------------------------------------------
- * NVRAM Configuration
- *
- * Note: the MBX is special because there is already a firmware on this
- * board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we
- * access the NVRAM at the offset 0x1000.
- */
-#define CONFIG_ENV_IS_IN_NVRAM	1	/* turn on NVRAM env feature */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_NVRAM_BASE + 0x1000)
-#define CONFIG_ENV_SIZE		0x1000
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-/* #define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME) */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC11 | SIUMCR_SEME | SIUMCR_BSC )
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF | PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit - leave PLL multiplication factor unchanged !
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	(SCCR_RTDIV | SCCR_RTSEL)
-#define CONFIG_SYS_SCCR	SCCR_TBS
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-#define CONFIG_SYS_PCMCIA_INTERRUPT	SIU_LEVEL6
-
-#define CONFIG_PCMCIA_SLOT_A	1
-
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
-#undef	CONFIG_IDE_LED			/* LED	 for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-
-/*-----------------------------------------------------------------------
- * Debug Entry Mode
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/MBX860T.h b/include/configs/MBX860T.h
deleted file mode 100644
index 74f44df682..0000000000
--- a/include/configs/MBX860T.h
+++ /dev/null
@@ -1,395 +0,0 @@
- /*
-  * A collection of structures, addresses, and values associated with
-  * the Motorola 860T MBX board.
-  * Copied from the FADS stuff, which was originally copied from the MBX stuff!
-  * Magnus Damm added defines for 8xxrom and extended bd_info.
-  * Helmut Buchsbaum added bitvalues for BCSRx
-  * Rob Taylor coverted it back to MBX
-  *
-  * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
-  */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#include <mpc8xx_irq.h>
-
-#define CONFIG_MPC860		1
-#define CONFIG_MPC860T		1
-#define CONFIG_MBX		1
-
-#define	CONFIG_SYS_TEXT_BASE	0xfe000000
-
-#define CONFIG_8xx_CPUCLOCK	40
-#define CONFIG_8xx_BUSCLOCK	(CONFIG_8xx_CPUCLOCK)
-#define TARGET_SYSTEM_FREQUENCY 40
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#define CONFIG_BAUDRATE		9600
-
-#define MPC8XX_FACT	10				/* Multiply by 10		*/
-#define MPC8XX_XIN	40000000		/* 50 MHz in	*/
-#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
-#if 1
-#define CONFIG_8xx_BOOTDELAY	-1	/* autoboot disabled		*/
-#define CONFIG_8xx_TFTP_MODE
-#else
-#define CONFIG_8xx_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#undef	CONFIG_8xx_TFTP_MODE
-#endif
-
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_DRAM_SPEED	(CONFIG_8xx_BUSCLOCK)	/* MHz		*/
-#define CONFIG_BOOTCOMMAND	"bootm FE020000"	/* autoboot command */
-#define CONFIG_BOOTARGS		" "
-/*
- * Miscellaneous configurable options
- */
-#undef	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#define	CONFIG_SYS_PROMPT		":>"		/* Monitor Command Prompt	*/
-#define	CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#define	CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0800000	/* 4 ... 8 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR			0xFFA00000
-#define CONFIG_SYS_IMMR_SIZE		((uint)(64 * 1024))
-#define CONFIG_SYS_NVRAM_BASE		0xFA000000 /* NVRAM                          */
-#define CONFIG_SYS_NVRAM_OR		0xffe00000 /* w/o speed dependent flags!!    */
-#define CONFIG_SYS_CSR_BASE		0xFA100000 /* Control/Status Registers       */
-#define CONFIG_SYS_PCIMEM_BASE		0x80000000 /* PCI I/O and Memory Spaces      */
-#define CONFIG_SYS_PCIMEM_OR		0xA0000108
-#define CONFIG_SYS_PCIBRIDGE_BASE	0xFA210000 /* PCI-Bus Bridge Registers       */
-#define CONFIG_SYS_PCIBRIDGE_OR	0xFFFF0108
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2f00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_VPD_SIZE	256 /* size in bytes reserved for vpd buffer */
-#define CONFIG_SYS_INIT_VPD_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_VPD_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_INIT_VPD_OFFSET-8)
-
-/*-----------------------------------------------------------------------
- * Offset in DPMEM where we keep the VPD data
- */
-#define CONFIG_SYS_DPRAMVPD		(CONFIG_SYS_INIT_VPD_OFFSET - 0x2000)
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x00000000
-/*0xFE000000*/
-#define CONFIG_SYS_FLASH_SIZE		((uint)(8 * 1024 * 1024))	/* max 8Mbyte */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_HWINFO_ADDR		(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_SYS_HWINFO_LEN)
-#define	CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* Reserve 256 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	4	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	16	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-/*-----------------------------------------------------------------------
- * NVRAM Configuration
- *
- * Note: the MBX is special because there is already a firmware on this
- * board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we
- * access the NVRAM at the offset 0x1000.
- */
-#define CONFIG_ENV_IS_IN_NVRAM	1	/* turn on NVRAM env feature */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_NVRAM_BASE + 0x1000)
-#define CONFIG_ENV_SIZE		0x1000
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF | PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit - leave PLL multiplication factor unchanged !
- */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	(SCCR_RTDIV | SCCR_RTSEL)
-#define CONFIG_SYS_SCCR	SCCR_TBS
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER		0
-
-/* Because of the way the 860 starts up and assigns CS0 the
-* entire address space, we have to set the memory controller
-* differently.  Normally, you write the option register
-* first, and then enable the chip select by writing the
-* base register.  For CS0, you must write the base register
-* first, followed by the option register.
-*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-/* the other CS:s are determined by looking at parameters in BCSRx */
-
-
-#define BCSR_ADDR		((uint) 0xFF010000)
-#define BCSR_SIZE		((uint)(64 * 1024))
-
-#define FLASH_BASE0_PRELIM	0xFE000000	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0xFF010000	/* FLASH bank #0	*/
-
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xFFF00000	/* OR addr mask */
-
-/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0	*/
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(0xFF800000 | OR_CSNT_SAM | OR_BI | OR_SCY_3_CLK)   /* 1 Mbyte until detected and only 1 Mbyte is needed*/
-#define CONFIG_SYS_BR0_PRELIM	(0xFE000000 | BR_V )
-
-/* BCSRx - Board Control and Status Registers */
-#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM	0xFFC00000 | OR_ACS_DIV4
-#define CONFIG_SYS_BR1_PRELIM	(0x00000000 | BR_MS_UPMA | BR_V )
-
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA		97		/* start with divider for 100 MHz	*/
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#define CONFIG_SYS_MAMR		0x13821000
-
-/* values according to the manual */
-
-
-#define PCMCIA_MEM_ADDR		((uint)0xff020000)
-#define PCMCIA_MEM_SIZE		((uint)(64 * 1024))
-
-#define	BCSR0			((uint) (BCSR_ADDR + 00))
-#define	BCSR1			((uint) (BCSR_ADDR + 0x04))
-#define	BCSR2			((uint) (BCSR_ADDR + 0x08))
-#define	BCSR3			((uint) (BCSR_ADDR + 0x0c))
-#define	BCSR4			((uint) (BCSR_ADDR + 0x10))
-
-/* FADS bitvalues by Helmut Buchsbaum
- * see MPC8xxADS User's Manual for a proper description
- * of the following structures
- */
-
-#define BCSR0_ERB       ((uint)0x80000000)
-#define BCSR0_IP        ((uint)0x40000000)
-#define BCSR0_BDIS      ((uint)0x10000000)
-#define BCSR0_BPS_MASK  ((uint)0x0C000000)
-#define BCSR0_ISB_MASK  ((uint)0x01800000)
-#define BCSR0_DBGC_MASK ((uint)0x00600000)
-#define BCSR0_DBPC_MASK ((uint)0x00180000)
-#define BCSR0_EBDF_MASK ((uint)0x00060000)
-
-#define BCSR1_FLASH_EN           ((uint)0x80000000)
-#define BCSR1_DRAM_EN            ((uint)0x40000000)
-#define BCSR1_ETHEN              ((uint)0x20000000)
-#define BCSR1_IRDEN              ((uint)0x10000000)
-#define BCSR1_FLASH_CFG_EN       ((uint)0x08000000)
-#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
-#define BCSR1_BCSR_EN            ((uint)0x02000000)
-#define BCSR1_RS232EN_1          ((uint)0x01000000)
-#define BCSR1_PCCEN              ((uint)0x00800000)
-#define BCSR1_PCCVCC0            ((uint)0x00400000)
-#define BCSR1_PCCVPP_MASK        ((uint)0x00300000)
-#define BCSR1_DRAM_HALF_WORD     ((uint)0x00080000)
-#define BCSR1_RS232EN_2          ((uint)0x00040000)
-#define BCSR1_SDRAM_EN           ((uint)0x00020000)
-#define BCSR1_PCCVCC1            ((uint)0x00010000)
-
-#define BCSR2_FLASH_PD_MASK      ((uint)0xF0000000)
-#define BCSR2_DRAM_PD_MASK       ((uint)0x07800000)
-#define BCSR2_DRAM_PD_SHIFT      (23)
-#define BCSR2_EXTTOLI_MASK       ((uint)0x00780000)
-#define BCSR2_DBREVNR_MASK       ((uint)0x00030000)
-
-#define BCSR3_DBID_MASK          ((ushort)0x3800)
-#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
-#define BCSR3_BREVNR0            ((ushort)0x0080)
-#define BCSR3_FLASH_PD_MASK      ((ushort)0x0070)
-#define BCSR3_BREVN1             ((ushort)0x0008)
-#define BCSR3_BREVN2_MASK        ((ushort)0x0003)
-
-#define BCSR4_ETHLOOP            ((uint)0x80000000)
-#define BCSR4_TFPLDL             ((uint)0x40000000)
-#define BCSR4_TPSQEL             ((uint)0x20000000)
-#define BCSR4_SIGNAL_LAMP        ((uint)0x10000000)
-#ifdef CONFIG_MPC823
-#define BCSR4_USB_EN             ((uint)0x08000000)
-#endif /* CONFIG_MPC823 */
-#ifdef CONFIG_MPC860SAR
-#define BCSR4_UTOPIA_EN          ((uint)0x08000000)
-#endif /* CONFIG_MPC860SAR */
-#ifdef CONFIG_MPC860T
-#define BCSR4_FETH_EN            ((uint)0x08000000)
-#endif /* CONFIG_MPC860T */
-#define BCSR4_USB_SPEED          ((uint)0x04000000)
-#define BCSR4_VCCO               ((uint)0x02000000)
-#define BCSR4_VIDEO_ON           ((uint)0x00800000)
-#define BCSR4_VDO_EKT_CLK_EN     ((uint)0x00400000)
-#define BCSR4_VIDEO_RST          ((uint)0x00200000)
-#define BCSR4_MODEM_EN           ((uint)0x00100000)
-#define BCSR4_DATA_VOICE         ((uint)0x00080000)
-
-#define CONFIG_DRAM_40MHZ		1
-
-#ifdef CONFIG_MPC860T
-
-/* Interrupt level assignments.
-*/
-#define FEC_INTERRUPT	SIU_LEVEL1	/* FEC interrupt */
-
-#endif /* CONFIG_MPC860T */
-
-/* We don't use the 8259.
-*/
-#define NR_8259_INTS	0
-
-#define CONFIG_CMD_NET
-/*
- * MPC8xx CPM Options
- */
-#define CONFIG_SCC_ENET 1
-#define CONFIG_SCC1_ENET 1
-#define CONFIG_FEC_ENET 1
-#undef  CONFIG_CPM_IIC
-#undef  CONFIG_UCODE_PATCH
-
-
-#define CONFIG_DISK_SPINUP_TIME 1000000
-
-
-/* PCMCIA configuration */
-
-#define PCMCIA_MAX_SLOTS    2
-
-#ifdef CONFIG_MPC860
-#define PCMCIA_SLOT_A 1
-#endif
-
-#endif	/* __CONFIG_H */
diff --git a/post/cpu/mpc8xx/ether.c b/post/cpu/mpc8xx/ether.c
index 91505475e8..53c0e4dfda 100644
--- a/post/cpu/mpc8xx/ether.c
+++ b/post/cpu/mpc8xx/ether.c
@@ -374,10 +374,6 @@ static void scc_init (int scc_index)
 	*((uchar *) BCSR0) |= BCSR0_ETHEN;
 #endif
 
-#ifdef CONFIG_MBX
-	board_ether_init ();
-#endif
-
 	/*
 	 * Set the ENT/ENR bits in the GSMR Low -- Enable Transmit/Receive
 	 */
diff --git a/post/cpu/mpc8xx/uart.c b/post/cpu/mpc8xx/uart.c
index 106a9b87d2..25d63d8120 100644
--- a/post/cpu/mpc8xx/uart.c
+++ b/post/cpu/mpc8xx/uart.c
@@ -141,10 +141,6 @@ static void smc_init (int smc_index)
 	up->smc_rfcr = SMC_EB;
 	up->smc_tfcr = SMC_EB;
 
-#if defined(CONFIG_MBX)
-	board_serial_init ();
-#endif
-
 	/* Set UART mode, 8 bit, no parity, one stop.
 	 * Enable receive and transmit.
 	 * Set local loopback mode.