Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm:
  arm, davinci: add DAVINCI_MMC_CLKID
  arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
  arm, davinci: da850/dm365 lowlevel cleanup
  omap5: Add omap5_evm board build support.
  omap4/5: Add support for booting with CH.
  omap5: emif: Add emif/ddr configurations required for omap5 evm
  omap5: clocks: Add clocks support for omap5 platform.
  omap5: Add minimal support for omap5430.
  omap: Checkpatch fixes
  omap4: make omap4 code common for future reuse
  GCC4.6: Squash warnings in onenand_base.c
  GCC4.6: Fix common/usb.c on xscale
  OneNAND: Add simple OneNAND SPL
  PXA: vpac270: Enable the new generic MMC driver
  PXA: Cleanup serial_pxa
  PXA: Drop csb226 and innokom boards (unmaintained)
  m28evk: Fix comment about the number of RAM banks
  mx31: Fix checkpatch warnings in generic.c
  mx31: Use proper IO accessor for GPR register
  mx31: Remove duplicate definition for GPR register
  qong: Use generic function for configuring GPR register
  M28EVK: Enable USB HOST support
  iMX28: Add USB HOST driver
  iMX28: Add USB and USB PHY register definitions
  M28: Add memory detection into SPL
  iMX28: Fix ARM vector handling
  M28: Add doc/README.m28 documentation
  M28: Add MMC SPL
  iMX28: Add support for DENX M28EVK board
  iMX28: Add u-boot.sb target to Makefile
  iMX28: Add image header generator tool
  iMX28: Add driver for internal RTC
  iMX28: Add GPMI NAND driver
  iMX28: Add APBH DMA driver
  iMX28: Add SPI driver
  iMX28: Add GPIO control
  iMX28: Add I2C bus driver
  iMX28: Add PINMUX control
  FEC: Add support for iMX28 quirks
  iMX28: Add SSP MMC driver
  iMX28: Initial support for iMX28 CPU
  MX25: zmx25: GCC4.6 fix build warnings
  da850: add new config file for AM18xx
  BeagleBoard: config: Switch to ttyO2
  OMAP3: Change omap3_evm maintainer
  devkit8000: Fix NAND SPL on boards with 256MB NAND
  integrator: enable Vpp and disable flash protection
  integrator: add system controller header
  integrator: make flash writeable on boot
  integrator: use io-accessors for board init
  integrator: move text offset to config
  integrator: pass configs for core modules
  ARM: remove superfluous setting of arch_number in board specific code.
  SPL: Allow ARM926EJS to avoid compiling in the CPU support code
  integrator: do not test first part of the memory
  arm: a320: fix broken timer
  ARM: define CONFIG_MACH_TYPE for all ronetix boards
  dm646x: pass board revision info to kernel
  dm646x: add new configuration for dm6467T
  arm, davinci: Fix setting of the SDRAM configuration register
  arm, davinci: Remove the duplication of LPSC functions
  arm, davinci: Rename AM1808 lowlevel functions to DA850
  da8xxevm: fix build error
  ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE

1 files changed, 267 insertions, 0 deletions

diff --git a/arch/arm/cpu/armv7/omap-common/hwinit-common.c b/arch/arm/cpu/armv7/omap-common/hwinit-common.c
new file mode 100644
index 0000000000..f65705db12
--- /dev/null
+++ b/arch/arm/cpu/armv7/omap-common/hwinit-common.c
@@ -0,0 +1,267 @@
+/*
+ *
+ * Common functions for OMAP4/5 based boards
+ *
+ * (C) Copyright 2010
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ *	Aneesh V	<aneesh@ti.com>
+ *	Steve Sakoman	<steve@sakoman.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/sizes.h>
+#include <asm/emif.h>
+#include <asm/omap_common.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * This is used to verify if the configuration header
+ * was executed by rom code prior to control of transfer
+ * to the bootloader. SPL is responsible for saving and
+ * passing the boot_params pointer to the u-boot.
+ */
+struct omap_boot_parameters boot_params __attribute__ ((section(".data")));
+
+#ifdef CONFIG_SPL_BUILD
+/*
+ * We use static variables because global data is not ready yet.
+ * Initialized data is available in SPL right from the beginning.
+ * We would not typically need to save these parameters in regular
+ * U-Boot. This is needed only in SPL at the moment.
+ */
+u32 omap_bootmode = MMCSD_MODE_FAT;
+
+u32 omap_boot_device(void)
+{
+	return (u32) (boot_params.omap_bootdevice);
+}
+
+u32 omap_boot_mode(void)
+{
+	return omap_bootmode;
+}
+#endif
+
+void do_set_mux(u32 base, struct pad_conf_entry const *array, int size)
+{
+	int i;
+	struct pad_conf_entry *pad = (struct pad_conf_entry *) array;
+
+	for (i = 0; i < size; i++, pad++)
+		writew(pad->val, base + pad->offset);
+}
+
+static void set_mux_conf_regs(void)
+{
+	switch (omap_hw_init_context()) {
+	case OMAP_INIT_CONTEXT_SPL:
+		set_muxconf_regs_essential();
+		break;
+	case OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL:
+#ifdef CONFIG_SYS_ENABLE_PADS_ALL
+		set_muxconf_regs_non_essential();
+#endif
+		break;
+	case OMAP_INIT_CONTEXT_UBOOT_FROM_NOR:
+	case OMAP_INIT_CONTEXT_UBOOT_AFTER_CH:
+		set_muxconf_regs_essential();
+#ifdef CONFIG_SYS_ENABLE_PADS_ALL
+		set_muxconf_regs_non_essential();
+#endif
+		break;
+	}
+}
+
+u32 cortex_rev(void)
+{
+
+	unsigned int rev;
+
+	/* Read Main ID Register (MIDR) */
+	asm ("mrc p15, 0, %0, c0, c0, 0" : "=r" (rev));
+
+	return rev;
+}
+
+void omap_rev_string(char *omap_rev_string)
+{
+	u32 omap_rev = omap_revision();
+	u32 omap_variant = (omap_rev & 0xFFFF0000) >> 16;
+	u32 major_rev = (omap_rev & 0x00000F00) >> 8;
+	u32 minor_rev = (omap_rev & 0x000000F0) >> 4;
+
+	sprintf(omap_rev_string, "OMAP%x ES%x.%x", omap_variant, major_rev,
+		minor_rev);
+}
+
+#ifdef CONFIG_SPL_BUILD
+static void init_boot_params(void)
+{
+	boot_params_ptr = (u32 *) &boot_params;
+}
+#endif
+
+/*
+ * Routine: s_init
+ * Description: Does early system init of watchdog, muxing,  andclocks
+ * Watchdog disable is done always. For the rest what gets done
+ * depends on the boot mode in which this function is executed
+ *   1. s_init of SPL running from SRAM
+ *   2. s_init of U-Boot running from FLASH
+ *   3. s_init of U-Boot loaded to SDRAM by SPL
+ *   4. s_init of U-Boot loaded to SDRAM by ROM code using the
+ *	Configuration Header feature
+ * Please have a look at the respective functions to see what gets
+ * done in each of these cases
+ * This function is called with SRAM stack.
+ */
+void s_init(void)
+{
+	init_omap_revision();
+	watchdog_init();
+	set_mux_conf_regs();
+#ifdef CONFIG_SPL_BUILD
+	setup_clocks_for_console();
+	preloader_console_init();
+	do_io_settings();
+#endif
+	prcm_init();
+#ifdef CONFIG_SPL_BUILD
+	/* For regular u-boot sdram_init() is called from dram_init() */
+	sdram_init();
+	init_boot_params();
+#endif
+}
+
+/*
+ * Routine: wait_for_command_complete
+ * Description: Wait for posting to finish on watchdog
+ */
+void wait_for_command_complete(struct watchdog *wd_base)
+{
+	int pending = 1;
+	do {
+		pending = readl(&wd_base->wwps);
+	} while (pending);
+}
+
+/*
+ * Routine: watchdog_init
+ * Description: Shut down watch dogs
+ */
+void watchdog_init(void)
+{
+	struct watchdog *wd2_base = (struct watchdog *)WDT2_BASE;
+
+	writel(WD_UNLOCK1, &wd2_base->wspr);
+	wait_for_command_complete(wd2_base);
+	writel(WD_UNLOCK2, &wd2_base->wspr);
+}
+
+
+/*
+ * This function finds the SDRAM size available in the system
+ * based on DMM section configurations
+ * This is needed because the size of memory installed may be
+ * different on different versions of the board
+ */
+u32 omap_sdram_size(void)
+{
+	u32 section, i, total_size = 0, size, addr;
+
+	for (i = 0; i < 4; i++) {
+		section	= __raw_readl(DMM_BASE + i*4);
+		addr = section & EMIF_SYS_ADDR_MASK;
+		/* See if the address is valid */
+		if ((addr >= DRAM_ADDR_SPACE_START) &&
+		    (addr < DRAM_ADDR_SPACE_END)) {
+			size = ((section & EMIF_SYS_SIZE_MASK) >>
+				   EMIF_SYS_SIZE_SHIFT);
+			size = 1 << size;
+			size *= SZ_16M;
+			total_size += size;
+		}
+	}
+
+	return total_size;
+}
+
+
+/*
+ * Routine: dram_init
+ * Description: sets uboots idea of sdram size
+ */
+int dram_init(void)
+{
+	sdram_init();
+	gd->ram_size = omap_sdram_size();
+	return 0;
+}
+
+/*
+ * Print board information
+ */
+int checkboard(void)
+{
+	puts(sysinfo.board_string);
+	return 0;
+}
+
+/*
+* This function is called by start_armboot. You can reliably use static
+* data. Any boot-time function that require static data should be
+* called from here
+*/
+int arch_cpu_init(void)
+{
+	return 0;
+}
+
+/*
+ *  get_device_type(): tell if GP/HS/EMU/TST
+ */
+u32 get_device_type(void)
+{
+	return 0;
+}
+
+/*
+ * Print CPU information
+ */
+int print_cpuinfo(void)
+{
+	char rev_string_buffer[50];
+
+	omap_rev_string(rev_string_buffer);
+	printf("CPU  : %s\n", rev_string_buffer);
+
+	return 0;
+}
+#ifndef CONFIG_SYS_DCACHE_OFF
+void enable_caches(void)
+{
+	/* Enable D-cache. I-cache is already enabled in start.S */
+	dcache_enable();
+}
+#endif